VIVO V001JB Pneumatic Arm Single Monitor Desk Mount Instruction Manual

June 6, 2024
Vivo

Pneumatic Arm Single Monitor Desk Mount
Instruction Manual
SKU: STAND-V001JB

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE MONITOR OR STAND.
USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE THE RISK OF TIP-OVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

VIVO V001JB Pneumatic Arm Single Monitor Desk -fig

TOOLS NEEDED

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1

Loosen the clamp screw on Clamp and Pole (A) until the opening is large enough to fit the edge of the desk. If the pole is loose in the base, twist the pole clockwise to tighten, then use the 3mm Allen Key (G) to tighten the set screw on the back of the base to lock the pole.

STEP 2
Place the Pole and Clamp (A) on the edge of the desk and tighten the clamp screw until securely mounted. If needed, the 5mm Allen Key (H) can be used to tighten the clamp screw. If the clamp is unable to open enough to fit the desk, remove the clamp screw from the base. Remove the bottom place and re- attach upside down, then re-insert the clamp screw.

STEP 3
Adjust the locating ring to the required height and tighten it to support the arm.

VIVO V001JB Pneumatic Arm Single Monitor Desk -fig 3

STEP 4
Slide the extension arm (C) onto the steel pole (A) until the arm (C) rests on top of the locating ring.

VIVO V001JB Pneumatic Arm Single Monitor Desk -fig 4

STEP 5
OPTION A: Flat Back Monitor
Use four M4x8 screws (I) or M4x12 screws (J) to secure the Spring Arm (B) to the monitor via mounting holes.

OPTION B: Curved Back Monitor
Place four plastic spacers (L) between the Spring Arm (B) and the monitor, then use four M4x30 screws (K) to secure the Spring Arm (B) to the monitor via mounting holes.

STEP 6
Carefully place the spring arm (B) with the monitor onto the extension arm (C), and secure using the M6x25 spring bolt (F) and Plastic Cap (D).

STEP 7
Use the 5mm Allen Key (H) to adjust the spring tension inside the arm (B) depending on the weight of your monitor. NOTE: Turn counter-clockwise to reduce tension for lighter monitors and clockwise to increase tension for heavier monitors.

VIVO V001JB Pneumatic Arm Single Monitor Desk -fig 8

STEP 8
Use the 3mm Allen Key (G) to adjust the arm swivel joints, and the 5mm Allen Key (H) to adjust the monitor swivel joint. Turn counter-clockwise to loosen and clockwise to tighten.

STEP 9
Insert the monitor cables into the cable covers on the underside of the arm (B). Leave enough slack to allow full adjustment and motion of the arm. Use the cable clip (E) to fasten cables to the steel pole (A).

VIVO V001JB Pneumatic Arm Single Monitor Desk -fig 10

**Love your new VIVO setup and want to share?
Tag us in your photo!
@vivo_us**

Open Monday – Friday 7:00 am – 7:00 pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

help@vivo-us.com| AVG. RESPONSE TIME (within office hrs): 1 HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
---|---
www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 4S

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.

VIVO V001JB Pneumatic Arm Single Monitor Desk -qr

 https://vivo-us.com/products/stand-v001jb

LAST UPDATED: 03/05/2020

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Vivo User Manuals

Related Manuals