EMEET 2ALCN-E7103 Microphone Speaker User Manual
- June 3, 2024
- eMeet
Table of Contents
EMEET 2ALCN-E7103 Microphone Speaker
EMEETOne (1) Year Limited Warranty
Limited one (1) Year Warranty with EM EET proof of purchase. The warranty does
not cover normal wear and tear or damage caused by accidents or misuse.
To protect your rights, please keep the proof of purchase. For service, please
contact us:
+1888 959 5320 (EST 9:00am-5:00pm)
support@emeet.com
www.emeet.com
Safety Guide
Caution:
To avoid electrical shock. do not open the housing of this product. In
addition, users do not need to use the product’s Internal parts. To repair the
product, please contact qualified maintenance personnel or mail the product to
our after-sales department.
- Please read this guide carefully.
- Please keep this guide.
- Please observe all warnings.
- Please follow all instructions.
- When cleaning this product, use a dry cloth only.
- Choking hazard -This product contains small parts. It is not suitable for children under the age of 3.
- Do not put this product near a heat source, such as a heating radiator, hot air regulator, stove, or loudspeakers (including amplifiers) that produce heat.
- Do not use this product if you must remain alert of your surroundings, for example, while driving a car or riding a bike.
- Do not submerge this product in water or expose it to a damp environment for a long period of time. Do not use this product when engaging in water sports, such as swimming or surfing.
- Please protect the power cable and audio cable. Do not step on or apply pressure on them. Do not pull on theproduct’s plug, socket, or cable outlet.
- It is recommended that users use the accessories that have been specified by the vendor.
- Do not expose the battery to environments with excessive heat, such as direct sunlight or sources of fire.
- Connect a power supply within the specified voltage range.
- If a power cable that is connected to the product is not currently being used to charge the product, please disconnect the power cable from the port and shut off the power supply.
- To repair the product please contact our professional maintenance personnel. If the product is damaged, the product should be repaired. For example, if the power cable or plug is damaged, liquid has flowed into the product, an object has fallen into the product; the product has come into contact with rain or moisture, the product cannot operate properly, or if the product has fallen.
Regulatory compliance Information
EU/UKCA Compliance:
Hereby, SHENZHEN EMEET TECHNOLOGY CO., LTD. Corporation declares that the
radio equipment is in compliance with . A copy of the EU/UK Declaration of
Conformity Is available at http://www.emeet.ai/Certificate.html
- The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction.
- lf you use a third-party charger, the recommended output voltage/current of the adaptor is 5Vdc/1 A., and the adapter shall be CE/UKCA approval type.
- lt is recommended to charge the product in an environment with a temperature that ranges from 5 ·c ~25 ‘C.
- Caution risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- Frequency: 2.4GHz (Bluetooth®)
- Maximum Power:: <100mW
- The suitable temperature for the product and accessories is 0~40 ·c.
- Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher.
- Excessive sound pressure from earphones and headphones can cause hearing loss.
IMDA Compliance:
Complies with IMDA Standards DA107974
FCC Compliance:
The device has been evaluated to meet general RF exposure requirement; The
device can be used in portable exposure condition without restriction Federal
Communication Commission (FCC) Radiation Exposure Statement.
Power is so low that no RF exposure calculation is needed.
This device complies with part 15 of the
FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital deviceJ pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>