Jumper T-LITE Remote Control User Guide
- June 6, 2024
- JUMPER
Table of Contents
Jumper T-LITE Remote Control User Guide
Radio Overview
- Antenna
- SB Position
- SD Position
- UP Buttons
- Down Buttons
- LED
- MDULEFT Buttons
- Gimbal
- T1-T4 Trim Button
- Power Button
- SA Position
- SC Position
- ENT Buttons
- RNT Buttons
- 1 3 ” LCD screen
- SYS/RIGHT Buttons
- Gimba
- T1-T4 Trim Button
- Speaker
- Single 18650 battery power supply
- External module
Power Requirements.
The T-LITE can work on vottagea 3.5v to 4.2v however for ease of use a 18650 is recommended Internal 1r18850 battery tray (not protected, recommend button top battery)
Main Screen Display
Model and Protocol Selection
The T-LITE, is cable of operating under many different protocols To view the most up to date list of compatible protocols please visit www.jumper- rc.com con Please note. new protocols are being added to the software all the tome Some protocols mayrequire the upgrading of your firmware
-
Press the Menu button and select the Model memory slot you wish to use.
-
Press the Page button to enter model setup then Navigate to the EXTERNAL RF options and under Mode select MULT.
-
Move the cursor to the second part of Mode and select the Protocol you wish to use then press enter to lock in the selection.
-
Different protocols will have different Binding sequences Please pay attention to Sub type and select the correct type for your model or receiver Follow Model or receiver manufactures binding stops.
Specifications.
Features:
STM32F205 MCU
OpenTX firmware
Screen: 1.3″ 128’84 LCD
High quality hall sensor gimbals
Internal Murb-protocol module
Improved ROM-LITE module slot, full speed TBS Crossfire NANO supported
Built in USS-C charging
Voice and Vibratron function
Spec:
Size 166 106 56mm
Weight_ 260g (with 18650)
Voltage. DC3 5-4 2V
Battery: 1×18650 (Battery not included)
Channel 16ch
External Micro SD Card:reserved SD card slot
Support.
Warranty and Repairs.
Please retain your proof of purchase and contact the retailer you purchased your T-LITE form should you experience any problems with your radios hardware.
Fimware Updates and openTX information.
For latest news and firmware updates from the Open•Source software development team please visit the openTX website at https://www:open-tx.com
Quick Sart User Manual.
A digital copy quick start guide e& available from www.jumper- rc.com
Introduction
Thank !mu for purchasing the Jumper T-LITE Mutti-protocol Radio system. Jumper
is proud to bring this ground-breaking product to the market and would like to
thank customers just like you and the community for making this dream possible
Please lake a moment to read this quick start reference before using your new
T-LITE radio
Happy flying
The Jumper Development en( team
Safety & Precautions
Many radio control models are equipped with powerful motors and sharp sic-Ann mg propellers Please exercise caution when working on models Ensure power is disconnected from your modek and remove propellers when performing maintenance
Do not operate the T-LITE radio system under the follow conditions.
- During bad weather or high wind conditions such as rain. twain, snow, storms or electromagnetic events_
- During any conditions of limited visibility.
- In areas where people, property, powerlines, roads, vehicles Of animals may be in present
- If you are felling tired or unwell or under the Influence of drugs or alcohol
- If the radio or model appear to be damaged or not functioning correctly.
- In areas of high 2 4GHz interference or In locations where use of 2 4GHz radios is prohibited
- When the battery is the T-LITE or the model is too tow to function.
Manuals and firmware downloads
The T-LITE is are shipped with openTX software installed as standaed To download the latest Software manual please visit http://www.open- tx.org/downloads
To download the latest firmware for your radio please visit the openT X webs/tie at the following link. http://www.open-tx.org/downloads
CAUTION
The T-LITE is shipped with the most stable firmware at the time of manufacture. Please only update firmware if you are experienced and confident in updating system firmware. Incorrect updates may render the radio inoperable.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>