SW-MOTECH BC.TRS.11.249.50200 Legend Gear Tank Strap Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.TRS.11.249.50200 Legend Gear Tank Strap
MOUNTING INSTRUCTIONS
Legend Gear Tank Strap SLA
Thank you for choosing this premium product from SW-MOTECH.
- Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw-motech.com
- Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference. SW-MOTECH assumes no liability for damages caused by improper fixation and handling.
- This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed.
- Installed accessories can change driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration.
PREPARATION
Read the mounting instructions carefully and make sure that all parts are
included. Make sure that your vehicle is parked safely and cannot fall over.
Turn off the engine and remove the ignition key. Let the motor/exhaust cool
off if necessary. Make sure to use only the appropriate tools. During
installation have another person help you.
FUNCTION CHECK
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream. After mounting, make sure there are no
clearance issues while the suspension is both compressed and extended.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
After fixation also make sure that no moving parts are obstructed and the
function of the vehicle is not hindered in any way. Lamps as taillight and
turn signals must not be limited in their function. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions.
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear-effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt. First remove dust and
encrustations with a soft dry brush. Remove stubborn deposits with a soft
cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning
tools or high pressure washer! Then rinse with clear water.
Before re-use dry the product for at least 24 hours in the air (not in direct
sunlight).
ATTENTION: Because the textile surfaces material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.I! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces, such as the paint. Make sure that all areas of the vehicle, which have contact with the product or parts of the product as straps, are protected with an adhesive protection film from scratches and abrasions. SW- MOTECH assumes no liability for paint damage and abrasions.
FIXATION
-
Carefully clean the surface of the tank (see “Care” section).
Remove the seat from the vehicle. Remove the two original screws and flanged spacers from the tank. -
Then attach the tank straps [1) with the original screws and flanged spacers [Orig.) to the tank.
Tighten the original screws [Orig.) with the manufacturer’s specified torque. -
Place the front strap of the tank strap [1) around the steering head of the vehicle, as shown in the drawing.
ATTENTION: Make sure there are no cables and/or tubes between the tank strap and vehicle frame!
Secure the buckle with the front strap of the tank strap [1 I. as shown in the detail drawing.
Legend Gear Accessory Bag LA 1 / LA2 / LAS & Legend Gear Smartphone Bag LA3
Thank you for choosing this premium product from SW-MOTECH.
- Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw-motech.com
- Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference. SW-MOTECH assumes no liability for damages caused by improper fixation and handling.
- This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed.
- Installed accessories can change driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration.
PREPARATION
Read the mounting instructions carefully and make sure that all parts are
included. Make sure that your vehicle is parked safely and cannot fall over.
Turn off the engine and remove the ignition key. Let the motor/exhaust cool
off if necessary. Make sure to use only the appropriate tools. During
installation have another person help you.
FUNCTION CHECK:
This is a universal product. For this reason make sure BEFORE the first use,
that the product can be fixed properly and used without problems with your
vehicle type.
ATTENTION: All components of the product must not contact any hot or
moving parts of the vehicle. All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream. After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
After fixation also make sure that no moving parts are obstructed and the
function of the vehicle is not hindered in any way. Lamps as taillight and
turn signals must not be limited in their function. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions.
LOADING INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
Never store pointy or sharp-edged objects in the product, which could cause
injury to persons or damage to the vehicle/product.
Use a waterproof inner bag/raincover to protect your luggage from moisture.
Additionally protect sensitive luggage (e.g., electronic equipment) from
moisture with a plastic bag.
ATTENTION: Maximum load: 1 kg / 2.2 lbs! The maximum vehicle load specified by
the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product, 130 km/h!
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear-effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn
deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning
agents, rough cleaning tools or high pressure washer! Then rinse with clear
water.
Before re-use dry the product for at least 24 hours in the air (not in direct
sunlight).
We recommend to impregnate the cotton textile surface of the product in
regular intervals or after intensive cleaning with a commercial wax
impregnation (e.g. from Fjallravenl.
ATTENTION: Because the textile surfaces material is a natural fiber, it
will experience color changes or fading when exposed to direct sunlight for
extended periods of time and by environmental factors (e.g., SMOG, acid rain,
etc.)! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can
damage surfaces, such as the paint. Make sure that all areas of the vehicle,
which have contact with the product or parts of the product as straps, are
protected with an adhesive protection film from scratches and abrasions. SW-
MOTECH assumes no liability for paint damage and abrasions.
FIXATION
The bags [1a) – [1d) can be attached to many products of the Legend Gear
series with the universal fixation system.
ATTENTION: Use the cell phone bag (1 d) only in combination with a tank bag or
accessory bag LA2 / LAS, because the bag itself has no protection from
moisture! Protect your smartphone with the rain cover of these bags from
getting wet!
-
NOTE: The bags (1a/ – (1d/ should be only fixed in the empty state.
Run both straps through the loops [1] of your Legend Gear product, then through the loops [2] of the bag. Tighten the straps. -
Now run the straps through the loops [3] and [4]. Tighten the fastening straps once more.
-
Now run the fastening straps through the loops [5]. Tighten the straps. Insert the reinforced ends of the straps completely into the loops [6] of the bag.
Check the proper fit of the bag.
T-Lock holder with MOLLE adapter
- Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
- Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
- Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
- This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TOV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION
Read the mounting instructions carefully and make sure that all items of the
parts list are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Use appropriate tools. Have another person
to help you.
MOUNTING
All parts and connections removed from the vehicle must be reinstalled in
accordance with the vehicle manufacturers· specifications or replaced by parts
delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with
medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK
After installation make sure that all parts and connections previously removed
are properly replaced. Also make sure that no moving parts are obstructed and
no function of the vehicle is hindered in any way. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions. After the first 50 km and then at regular intervals, check
the tightening torque of all screw connections and the proper fit of the
product.
PARTS LIST
ur11| TL.00.940.003| Adapter| Adapter| 212|
---|---|---|---|---|---
: [2]| TL.00.940.004| Mutter| Nut| 1 /1|
| | | | |
B1r31| TL.00.940.001| T-Lock Halter| T-Lock Mount| 1 /1|
! [4]| M5 x 6; DIN 6912| lnnensechskantschraube, fl. Kopf;
Edelstahl| Hexagon Socket Screw, short head; stainl. steel| 1 /1|
0,5
: [5]| TL.00.940.005| Abdeckkappe| Cover Cap| 1 /1|
| | | | |
0(6]| TL.00.940.002| MOLLE-Adapter| MOLLE Adapter| 1 /1|
Note: a All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery.
MOUNTING
MOUNTING OF THE MOLLE ADAPTERS
-
Step [11: Insert the nut (2) in one of the two adapters (1].
ATTENTION: The stamped number must point upwards! -
Step [2]: Now push the wings of the adapter l1) with a rotating movement under the MOLLE attachment. Keep the nut (2) in position.
-
Step [3]: Slide in the opposite direction the wings of the second adapter [1) under the MOLLE attachment.
ATTENTION: Make sure that the hexagon recess is aligned upwards! -
Step [41: Attach the T-Lock holder 13 to the adapters (1).
ATTENTION: Use liquid thread locker, suitable for plastic leg. Loctite 425]! Tighten the screw as specified.
ATTENTION: Over-tightening the screw will damage the plastic parts!
FIXING THE BAG TO THE MOLLE ADAPTER
NOTE: The bag should be only fixed in the empty state.
-
Step [5]: Pass the two straps through the loops of your bag.
-
Step [6]: Then pass the two straps through the openings of the MOLLE Adapter (6).
-
Step [7]: Now press the four tabs of the MOLLE Adapter (6] under the loops of the bags. This requires some force.
TIP: Use a blunt, flat object like a butter knife to gently lift the loops. -
Step [8]: Tighten the straps and press the reinforced ends under the shown loops.
FIXATION OF THE BAG
- Step [8]: Place the MOLLE adapter (6) on the T-Lock holder (3).
- Step [9]: Attach the bag to the T-Lock holder (3) with a 90 degree turn clockwise. Check the proper fit of the bag (before every ride).
To release, simply turn the bag counterclockwise.
TIP: Use the rotation lock of the
T-Lock holder (3) to turn the adapters (1 J out of the MOLLE attachment (see left detail drawing. Make sure that the rotation lock initially only engages the upper adapter (1 ].
Technische und Design-Anderungen vorbehalten.
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg Germany
Tel. I phone+ 49 (0)6425 / 8168 – 050 Fax / fax+ 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>