DJI Action 2 User Guide

: June 6, 2024
: DJi

Table of Contents

DJI Action 2
Safety at a Glance
Specifications
Compliance Information
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DJI Action 2

Safety at a Glance

Please read this entire document and visit http://www.dji.com/action-2 to view the user manual, other documents, and the tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may result in personal injury, damage to your DJI OSMOTM product, or other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of DJI OSMO.
By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of this document. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. This product is not intended for use by children without direct adult supervision.

WARNING

DJI ActionTM 2 contains magnets. Keep the camera unit away from magcards, IC cards, hard disks, RAM chips, implantable medical devices such as pacemakers, and other devices to avoid interference.
All the holes on the camera unit have built-in waterproof material. DO NOT poke the holes. Clean the camera unit with a clean, dry cloth after using under water.
DO NOT attach the camera unit to the power module when there is any dust or water on the expansion ports. Otherwise, the camera unit may corrode or short-circuit.
Put out any product fire using water, sand, fire blanket, or a dry powder fire extinguisher.
The product should be used in temperatures from 0º to 40ºC (32° to 104°F). Use of the product in environments above 40ºC (104°F) can lead to a fire or explosion. Use of the product below 0ºC (32°F) can lead to permanent damage.
Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
DO NOT drop or strike the product. DO NOT place heavy objects on the product.
DO NOT heat the product. DO NOT put the product in a microwave oven or in a pressurized container.
DO NOT leave the product near heat sources such as a furnace or heater. DO NOT leave the product inside of a vehicle on hot days. The ideal storage temperature is 22ºC to 28ºC (72° to 82°F).
DO NOT store the product fully discharged for an extended period. Otherwise, it will over discharge, which will lead to permanent damage.

CAUTION

Intricate components inside DJI Action 2 may be damaged upon impact and cause the camera unit to malfunction.
Keep the lens glass clean. Sand and dust may damage the lens glass. Clean DJI Action 2 with a clean, dry cloth.
Make sure to be careful if the lens glass breaks.
Keep DJI Action 2 away from sand and dust. Wash the camera unit if the holes are blocked by sand, dust, or any other substance.
DO NOT poke the USB-C port or microSD card slot.
DO NOT expose DJI Action 2 to extreme cold or hot temperature. Otherwise, the operating time and functionality may be negatively affected.
DO NOT use DJI Action 2 during lightning storms.
DO NOT disassemble or repair DJI Action 2 by yourself.
DO NOT use DJI Action 2 inside hot springs. DO NOT allow DJI Action 2 to come into contact with corrosive or unknown liquids.
When attaching DJI Action 2 to the roof or window of a car, the camera unit may fall off if the car travels too fast, the surface is not clean, or there is bad weather such as high winds or a thunderstorm.
The power module is not waterproof. The waterproof case is required when using the power module with the camera unit under water.
Charge DJI Action 2 when the battery level is low. Storing the camera unit for more than four months with low battery will reduce the battery life.
Discharge the battery to 40-60% if DJI Action 2 will not be used for 10 days or more. This can greatly extend the battery life.

Specifications

Model: MC211
Wi-Fi
- Operating Frequency: 2.400-2.4835 GHz, 5.150-5.250 GHz, 5.725-5.850 GHz
- Transmitter Power (EIRP): 2.4 GHz: <16 dBm (FCC/CE/SRRC/MIC), 5.1 GHz: <14 dBm (FCC/CE/SRRC/MIC), 5.8 GHz: <14 dBm (FCC/CE/SRRC)
- Protocol: 802.11a/b/g/n/ac
Bluetooth
- Operating Frequency: 2.400-2.4835 GHz
- Transmitter Power (EIRP): < 4 dBm
- Protocol: BLE 5.0
Operating Temperature: 0° to 40°C

Compliance Information

FCC Compliance Notice

Supplier’s Declaration of Conformity
Product name: DJI Action 2
Model Number: MC211
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

ISED Compliance Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.