Tratenor UIC680EZ Contactless Smart Card Reader Instruction Manual
- July 26, 2024
- Tratenor
Table of Contents
Tratenor UIC680EZ Contactless Smart Card Reader
Product Information
Specifications
- Product Name: UIC680EZ Contactless Smart Card Reader
- Communication Interface: RS232
- SAM (Security Access Module): Included
- I/O Connector: Available
- LED Indicators: Yes
- Power Supply: External
- Physical Dimensions: Available in manual
- Safety: ESD protection
Product Usage Instructions
- Plug the RS232 cable into the port of the PC or system.
- The reader will boot up automatically.
FAQ
- Q: What should I do if the reader does not boot up automatically?
- A: Check the RS232 cable connection and ensure it is securely plugged into the correct port. If the issue persists, refer to the troubleshooting section in the user manual for further assistance.
- Q: How do I know if the reader is functioning correctly?
- A: The LED indicators on the reader will provide visual cues to indicate its status. Refer to the user manual for a detailed explanation of the LED indicator patterns.
Specification
| Reader | UIC680EZ |
|---|---|
| Communication Interface | Ethernet |
LTE (optional) UART x2
USB Host/Device (depend on UIC680FGP model)
SAM| 4 slots (Optional)
I/O Connector| Independent Mode:
1.Connector x1 : RS232 w/ 5VDC 1A power input. 2.Connector x1 : UART.
3. Connector x1 : Ethernet.
4. Connector x1 : USB Host/Device(SW config) 5.Connector x1: I2C connect SAM board.
6. Connector x 1: DC IN CONN
LED Indicators| LAN Indicator x2 (IO Board)
Power Indicator x1 (IO Board) System Indicator x2 (IO Board)
Power Supply| 5VDC +/- 5%, 4A
Physical Dimension| 93 mm x 82 mm x 29.3 mm (Holder Type)
Safety| FCC Class B, CE Class B, IC(ISED)
ESD| ±8KV Contact
Operating| Temperature -30°C to 70°C
Storage| Temperature -30°C to 80°C
Humidity| 5 to 90% (Non condensing)
Installation guide(RS232 Interface)
1| Plug the RS232 cable into the port of PC or system
2| The reader will boot up automatically
|
Product Overview
CAUTION
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC STATEMENT
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used under the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Suppose this equipment does cause harmful interference to radio or television
on reception, which can be determined by turning the equipment off and on. In
that case, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF exposure statements
- This Transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons..
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>