OCULAR IOCAP06C-7 IQ Dual Port Tower Installation Guide

OCULAR IOCAP06C-7 IQ Dual Port Tower

IMPORTANT!
READ THIS ENTIRE DOCUMENT BEFORE INSTALLING OR USING THE CHARGER. FAILURE TO DO SO
OR TO FOLLOW ANY OF THE INSTRUCTIONS AND WARNINGS IN THIS DOCUMENT CAN RESULT IN FIRE, ELECTRICAL SHOCK, SERIOUS INJURY OR DEATH.
THE CHARGER MUST BE INSTALLED
BY A QUALIFIED ELECTRICIAN.
THE ENTIRE INSTALLATION MUST COMPLY WITH THE LATEST “AS/NZS3000:2018 & AS/NZS:3008 STANDARDS”

SPECIFICATIONS

PRODUCT OVERVIEW

1. Wi-Fi & 4G Antenna

2. LED Indicator

3. Optional Programmable Button
   (Charging Port Selection is set up as default

4. 7” LCD screen

5. RFID card reader

6. Internal MCB-RCD circuit

FEATURES

Integrated RCD Type B
The Ocular IQ Tower is designed to meet and comply with the AS/NZS3000:2018 Wiring Rules
With an inbuilt integrated RCD Type B, the installer will only need to install a Type A RCBO at the distribution board.

LCD Screen & RFID Reader
The Ocular IQ Tower is equipped with a 7 inch LCD screen allowing users to know the status of the charger. Details about the LCD screen can be found on pages 10 – 12.
The Ocular IQ Tower charger comes with an inbuilt RFID reader to allow for access control to the charging station. The RFID Reader is compatible with all ISO 14443 A/B RFID Cards.

Self-Monitoring & Recovery
The charger will automatically resume charging after a minor fault such as OVP, UVP, OTP or OCP with no user intervention required.

OCPP 1.6J Full Profiles & Smart Charging Support
The charger supports OCPP 1.6J full profiles, including the latest smart charging to balance the load of charging stations with limited power supply.

SAFETY INSTRUCTION

WARNING!

• Do not install or use the charger near flammable, explosive, harsh, or combustible materials, chemicals, or vapors.
• Turn off input power at the circuit breaker before installing or maintaining.
• Do not use or stop using the charger if it is defective, appears cracked, frayed, broken or other-wise damaged, or fails to operate.
• Do not attempt to open, disassemble, repair, tamper with, or modify the charger.
• The charger is not user serviceable. Contact your installer for any repairs.
• Do not use the charger when either you, the vehicle or the charger is exposed to severe rain, snow, electrical storm or other inclement weather.
• Do not touch the charger sockets with sharp metallic objects, such as wire, tools or needles.
• Do not put fingers into the charger sockets.
• Do not use this charger if the EV charging cable is frayed, has broken insulation, or displays any other indication of damage.
• Do not use this charger if the enclosure or the EV charging connector is broken, cracked, open, or shows any other indication of damage.

CAUTIONS!

• The charger should be installed only by a qualified electrician.
• Make sure that the materials used and the installation procedures follow local building codes and safety standards.
• Incorrect installation and testing of the charger could potentially damage either the vehicle’s Battery and/or the charger itself. Any resulting damage is excluded from the warranty for both the vehicle and the charger. Do not operate the charger in temperatures outside its operating range of -30°C to +50°C.
• Ensure that the EV charging cable is positioned properly to the charging sockets.
• Do not use cleaning solvents to clean any of the charger’s components.
• Be careful not to damage the circuit board when removing the power entry knock-out.

INSTALLATION

Tools Required

• Slotted #6 screwdriver
• Philips #2 screwdriver
• Terminal crimper
• Adjustable spanner Overview of Steps

TURN OFF THE POWER SUPPLY.
Then follow these steps to install the Charger:

No. : Steps

1. Check box contents.
2. Concrete anchoring.
3. Power cable wiring.
4. Internet connection.
5. Verify the installation.
6. Secure cover and power up.

Step 01 – Check Box Contents
If any components are damaged or missing, please contact your installer or Ocular charging.

• Pedestal Charger

• Backplate Key x 1

• Terminal crimps x 5

Step 02 – Floor Mounting

1. Open the charger backplate with the key provided.

2. Remove the screws and open the guard plate.
   

3. Anchor the charger to the concrete basement

Step 03 – Power Cable Wiring
Note: Power cables must be crimped with suitable ferrules otherwise product warranty will be voided

1. Cross the power cables through guard plate.

2. Connect the power cables to the connector board.

Step 04 – Internet Connection

Option 1.Cellular & Ethernet

No. : Item

1. Insert SIM card to the card slot for cellular connection.

2. Connect the internet cable for Ethernet connection.

Option 2. Wi-Fi

• Connect your device to the charger Wi-Fi SSID ‘ioc-XXXXXX’, and enter default password ‘IOC12345’.
• Open web-based setup page by entering the default IP Address ‘192.168.10.1:8900’, and enter Username ‘admin’ and Password ‘ioc12345’ then click ‘ok’.

Additional Notes

No.:  Item

1. Change the value to ‘true’ to activate the offline mode.
2. Ethernet supporting DHCP or static IP.
3. Scan the Wi-Fi to select the SSID to be connected.
4. Enter parameters from your ISP provider for cellular connection.

Step 05 – Verify The Installation

No.:  Item

1. Verify the power cables are wired properly.
2. Close the RCD to power on the charger unit, and you should see the LED lights sequentially illuminate green.
3. If the LED red light illuminates or flashes, refer to the Troubleshooting table .
4. Check on the screen display whether internet is available and back office is connected.
5. Test the live charging process with simulator or electric vehicle if the installation is completely verified.

Step 06 – Secure Cover

1. Reposition the backplate to the charger and lock it with the key.
2. Seal the back cover

LCD DISPLAY SCREEN

• Welcome Screen

• Scan the QR code or swipe the RFID card to start charging

• Connect the charging plug
  

• Charging in process
  

• Suspended by EV

• Remove the charging plug

• Automatic upgrade mode activated

• Software downloading and upgrading automatically
  

• Network upgrade mode

• Micro SD card upgrade mode

• Factory reset activated
  

• Invalid authorisation

• Not permitted to charge

• Failed to start charging
  

• Service not available

• Software update error

• Explanation of icons
  

TROUBLESHOOTING

MAINTENANCE & REPAIR

• Regularly inspect the Charger. If damage is found, contact your installer or Ocular Charging.
• The Charger contains no user-serviceable components. If unit is not operating correctly, contact your installer or Ocular Charging.
• Wipe the outside of the Pedestal Charger regularly with a clean damp cloth to remove
  any accumulation of dust and dirt to prevent rust.

References

• EV Charging Stations Australia | Electric Vehicle Charging Stations | Ocular Charging

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>