UBIQUITI UF-Instant User Guide
- June 6, 2024
- UBIQUITI
Table of Contents
UBIQUITI UF-Instant
Package Contents
Installation Requirements
- UFiber OLT
- Ubiquiti product with SFP
port For more information, refer to: ubnt.link/Using-UF- Instant
Before You Begin
Designing your rst GPON deployment requires speci c knowledge and planning. For information on GPON network design and installation, including important considerations and best practices, refer to:
- ubnt.link/UFiber-GPON-Getting-Started
- ubnt.link/Designing-a-GPON-Network For details on con guring U
Fiber devices for the rst time, refer to: ubnt.link/UFiberInitial- Configuration
Hardware Overview
PON Port
The SC/APC GPON port supports WAN connections of 2.488 Gbps downstream and
1.244 Gbps upstream.
SGMII
Interface
The SGMII Ethernet LAN interface supports a 1 Gbps connection.
Connecting Fiber
| WARNING: Never look directly into the ends of ber or modules. The
emitted light could cause damage to the eye.
---|---
| WARNING: Until ready for use, keep modules and ber patch cables covered
using the included protective caps to ensure the connections stay clean.
| WARNING: DO NOT connect the device directly to a UFiber GPON module
(UF-GPB+ or UF-GP-C+). Doing so will damage the device optics. Ensure that the
device’s
Connecting LAN
Configuration
The device only supports bridge mode and is con gured via the UFiber OLT. For more information, refer to the UFiber resources, which are available at: ubnt.link/UFiberSupport
Specifications
UF-Instant
Dimensions| 69.46 x 13.70 x 11.30 mm (2.74 x 0.54 x 0.45″)
Weight| 30 g (0.96 oz)
Networking Interfaces| (1) SC/APC, GPON WAN (1) SGMII Ethernet LAN
Networking Interface Speeds GPON WAN, ITU G.984 GbE LAN| 2.488 Gbps
Downstream, 1.244 Gbps Upstream 1 Gbps
Management Interface| In-Band Ethernet PON
Normal Optical Power Range| TX (Class B+): 0.5 to 5 dBm RX: -8 to -28 dBm
Power Method| SFP
Power Supply| 3.3V
Max. Power Consumption| 2W
Supported Voltage Range| 3.3V
Processor Specs| MIPS 100 MHz
Memory Information| 32 MB DDR
Operating Temperature| -10 to 45° C (14 to 113° F)
Operating Humidity| 10 to 90% Noncondensing
Operating Humidity| CE, FCC, IC
Safety Notices
- Read, follow, and keep these instructions.
- Heed all warnings.
- Only use attachments/accessories speci ed by the manufacturer.
| WARNING: To reduce the risk of re or electric shock, do not expose this
product to rain or moisture.
---|---
| WARNING: Do not use this product in location that can be submerged by
water.
| WARNING: Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
| WARNING: CLASS 1 LASER PRODUCT, IEC/EN 60825‐1:2014 – Do not look into
the ends of the ber optic cable or SFP modules while converters are powered.
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those speci ed may result in improper operation, damage to the equipment or pose a re hazard if the limitations are not followed.
- There are no operator serviceable parts inside this equipment. Service should be provided only by a quali ed service technician.
Limited Warranty
ui.com/support/warranty
Compliance
FCC
Changes or modi cations not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions.
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Canada
CAN ICES-3(B)/NMB-3(B)
Australia and New Zealand
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.
WEEE Compliance Statement
Declaration of Conformity
Online Resources
© 2020 Ubiquiti Inc. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>