mictrack MT825 Cat M1 and NB-IoT GPS Tracker User Manual

June 6, 2024
mictrack

Mictrack MT825 Cat M1 and NB-IoT GPS Tracker

mictrack MT825 Cat M1 and NB-IoT GPS Tracker featured

Preface
Congratulations on choosing the Mictrack MT825 CAT M1/NB-IoT GPS tracker. This manual shows how to easily program and setup the tracker for the best results. Make sure to read this manual carefully before using this product, so as to avoid delays or confusion with its operation. Please note that specifications and instructions are subject to change without notice to facilitate product improvement. Updates and changes will be integrated into the latest release. The manufacturer assumes no responsibility for any errors or omissions in outdated documents.

Overview

MT825 is a Mini waterproof GPS tracker that uses the latest CAT M1 & NB-IoT technology that can provide low power consumption and optimized data transmission with low cost. The parents or pet owners can track the unit via their smart phone even if far away. With the hybrid positioning system GPS and WiFi allow get more precise location. It can be used for personal(kids/elderly), pets and fleet management etc.

Features

  • CAT M1 & NB-IoT & GSM Network
  • Real-timing tracking
  • GPS+WiFi Positioning
  • History record check
  • Geo-Fence alarm
  • SOS Alarm report
  • Low battery alarm
  • Power saving mode
  • PC & Mobile App tracking
  • Long standby for 5 months
  • P65 Water-resistant
  • OTA
  • Open protocol

Applications

  • Kids & Elderly tracking
  • Lonely workers tracking
  • Pets tracking
  • Asset tracking

Specifications


Item

| Specifications
---|---
Dimension| 504016mm
Weight| 36g
Charging mode| Magnetic charging DC 5V
Backup battery| 3.7 V 680mAh
Power consumption| 45uA standby current


Item

| Specifications
---|---
Working temperature| -20°C to 65°C





Cellular Bands

| Cat M1 (LTE-M, eMTC)


LTE FDD: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28 LTE TDD: B39

NB-IoT (CAT NB1):


LTE FDD: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28


GSM: 850/900/1800/1900Mhz

Positioning| GPS, WiFi, LBS
Tracking Sensitivity| -162 dBm
Sensor| Accelerometer
LED| RED/GREEN
SIM Card interface| PUSH Nano SIM
Waterproof| IP65

MT825 interface

mictrack MT825 Cat M1 and NB-IoT GPS Tracker fig1

In the box

  • 1* MT825 GPS Tracker
  • 1* Magnetic charging cable
  • 1* Quick Start Guide
  • 1* USB Config Cable (optional)
  • 1* Pet collar (optional)
  • 1* Lanyard (optional)
Installation

SIM Card installation

  • Get ready a Nano Sim Card that support Cat M1 or NB-IoT with 15MB data a month

  • Open the waterproof rubber plug

  • Insert Sim card to sim card slot correctly(as the following image)
    watch the video: https://bit.ly/mt825

  • Press SOS button for 3 seconds to power ON (green led will blinking).

  • After that the device will be ready.
    mictrack MT825 Cat M1 and NB-IoT GPS Tracker fig2

LED Indications

Green indicator


Status

| Description
---|---
Solid Green| l   GPS & Network available
OFF| l   Device Power OFF or in sleep mode
Fast blinking (1s)| l   Network available only
Slow blinking (3s)| l   GPS available only
Slow blinking (6s)| l   Network & GPS unavailable

RED indicator


Status

| Description
---|---
Solid Red| In charging
OFF| No charge or full charged

Setup and Configuration

  • If you use NB-IoT SIM card, ONLY can setup the device via USB Config cable(because NB-IoT SIM do not support SMS)
  • If you use Cat M1 SIM card, you can setup the unit via following SMS commands (8.1-8.10) or via USB Config cable.
  • Download USB Config tool and guide/video from link: https://bit.ly/mt825-config-tool
Set APN (Access Point Name)

SMS Command format 1: apn,apn,,#
For example : apn,iot.nb,,#
SMS Command format 2: apn,apn,username,password# For example: apn,internet,internet,internet#
Reply: IMEI, apn=Success!

Set the IP and port

SMS Command format : data,ip:port#
For example : data,e.trackits.com:7700##
Reply: IMEI, data=Success!

Working mode

One report per day mode
SMS Command format: mode,0,T#
For examples: mode,0,8#
Reply: IMMEI, mode=Success!
Note: The device will wake up and report one data to the server at 8 AM every day, after that it will go to sleep again until next day at 8 AM. T is [0-23] hours.

Deep sleep interval mode
SMS Command format: Mode,1,T#
For examples: Mode,1,30#
Reply: IMEI, mode=success!
Note: Device will wake up and report one data to server every 30 minutes, after that it will go to sleep again until the next 30 minutes . T is [3-1440] minutes.

GPS sleep mode
SMS Command format: Mode,5,T#
For examples: Mode,5,10#
Reply: IMEI, mode=success!
Note: The device will wake up every 10 minutes and report one data to the server, after that it will go to sleep again until the next 10 minutes. T is [3-1440] minutes.

GPS always ON mode
SMS Command format: Mode,6,T#
For examples: Mode,6,10#
Reply: IMEI, mode=success!
Note:The device will report data every 10s .T is [10-86400] seconds.

Power Saving mode
SMS Command format: Mode,7,T#
For examples: Mode,7,10#
Reply: IMEI, mode=success!
Note: When the device detects continuous vibration for more than 10s, it will wake up and starts to connect to the network, After connected it will Immediately report a data (event 15) to the platform;

  • If the device is still in a vibrating state, MT825 will report to the server every 30 seconds/
  • If there is no vibration for more than 2 minutes, the device will automatically go to sleep and report a data((event 16) to server. T is [10-86400] seconds
Network mode

Setup to Cat M1 network only
SMS Command format : netlock,2,3,0#
Reply: IMEI, netlock=Success!
Note: In this mode device will only work under Cat M1 network.

Setup to NB-IoT network only
SMS Command format :netlock,3,3,1#
Reply: IMEI, netlock=Success!
Note: Device will only work under NB-IoT network.

**** SMS Command format : netlock,1,1,2#
Reply: IMEI, netlock=Success!
Note: Device will only work under GSM network.

Setup to AUTO Mode
SMS Command format : netlock,0,0,2#
Reply: IMEI, netlock=Success!
Note: Device will auto switch to the available network include Cat M1, NB-IoT and GSM.

Setup Protocol

Setup to TCP
SMS Command format: protocol, 1,0#
For examples: protocol,1,0#
Reply: IMEI, protocol=success!
Note: MT825 support TCK without ACK only.

Setup to UDP
SMS Command format: Logprint, 0,Z#
For examples: Logprint, 0,1#
Reply: IMEI,logprint=success!
Note: Z=[0,1]. To enable the print log, send command: Logprint,1#, To disable the print log, sent command: Logprint,0#

Logprint

SMS Command format: Logprint, 0,Z#
For examples: Logprint, 0,1#
Reply: IMEI,logprint=success!
Note: Z=[0,1]. To enable the print log, send command: Logprint,1#, To disable the print log, sent command: Logprint,0#

OTA

SMS Command format: otastart,ip:port,user name,password,firmware name,1#
For examples: otastart,112.74.53.63:21,ota,ota,MT825.bin,1#
Reply: IMEI, otastart =Success! OTADONE
It will response “OTADONE” if OTA successfully or response “OTAFAILED” when OTA fail. If it has failed, please try again.

Rconf

SMS Command format : rconf,0#
After send this command, the device will reply as follow:
UI:866425032478242
rconf=nbiot,,,e.trackits.com,7700,6,60,MT825_MICTRACK_B1.05V2.8_20210519,NB- IoT Note: According the above message and we can get the info as follow:
ID: 866425032478242
APN: nbiot
IP: e.trackits.com
Port: 7700,
Mode: Mode,6,60#
Version: MT825_MICTRACK_B1.05V2.8_20210519
Network: NB-IoT

Reboot

SMS Command format : reboot,0#
The device will restart after send this command. Reply: IMEI, reboot=Success!

Reset

SMS Command format : factoryreset,1#
The device will reset to default after send this command. Reply: IMEI, reset=Success!

App & PC Tracking platform

App install & Login

  • Search “Yi tracker” in Google Play or iOS store(or scan the following QR code) to download the Mobile APP(not Yi tracker2);
  • Choose the” Login by Device No., Input server www.trackits.com
  • Input your device’s ID number and password(default is 123456) to login.
    mictrack MT825 Cat M1 and NB-IoT GPS Tracker fig3

PC login

Troubleshooting

Issues Caused Solutions

Send SMS to the device but no reply

| 1>The device only reply with Cat

M1 sim card and will not reply the NB-IoT SIM card

| ****

Please check the SIM card status and try again.

 | 2>SIM Card have not active

3>Card balance is not enough

|
---|---|---


Text command format is wrong

| Please check the command format again



Connect network fail.

| Please check LED status and make sure the network

connect successful first.

GPS platform shows logged off|  | 1. Check the APN setting ;

2.   Check IP and port

3.   Check network if match

GPS platform shows no location or the coast of

Africa.

| Device indoor/garage| Take it outside for a

10-minute walk or drive, and its location should update.

LED no light| Backup battery is low power| Please charge the device for 30 minutes at least.

Any questions please do not hesitate to contact us:
Shenzhen Mictrack Electronics Co.,Ltd.
Add: B305-306, Kangsheng Electronic Industrial Park, Zhonghua Rd, Longhua District, Shenzhen, China 518131
Tel: +86-755-21014699
Web: www.mictrack.com
Email: info@mictrack.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals