mictrack MT510 3G Personal Tracker User Manual
- June 16, 2024
- mictrack
Table of Contents
MT510 3G Personal Tracker
User Manual V2.0
MT510 3G Personal Tracker
Preface
Thank you for choosing the 3G Personal GPS tracker.This manual shows how to
operate the device smoothly and correctly.Make sure to read this manual
carefully before using this product. Please note that specification and
information are subject to changes without prior notice in this manual. Any
change will be integrated in the latest release. The manufacturer assumes no
responsibility for any errors or omissions in this document.
Overview
MT510 is the latest 3G Personal tracker support WCDMA/UMTS.This device can
locate and monitor any remote targets by SMS/PC/APP.
The unit features excellent and stable work performance.It used for
personal,vehicle and pets.
Application
- 3G WCDMA/UMTS support
- Real-time position inquire
- Two way voice communication
- Voice monitoring
- Personal trip history on web
- SOS alarm
- Over-speed alarm
- Motion report
- Geo-fence alarm
- Backup battery low power alarm
- Power saving mode
- Mileage report
Specifications
Item | Specifications |
---|---|
Dimension | 89(L)57(W)20(H)mm |
Weight | 89g |
Charging Voltage | Micro USB interface DC 5V |
Backup battery | 1600mAh/3.7V |
Power consumption | 60mA standby current |
3G Frequency bands | MT510- **E |
900/2100MHz@UMTS
900/1800MHz@GSM\
MT510- A
850/1900MHz@UMTS
850/900/1800/1900MHz@GSM
MT510- T
850/2100MHz@UMTS
850/900/1800/1900MHz@GSM
Item| Specifications**
---|---
GPS Chip| U-BLOX7
GPS Sensitivity| -162dBm
Channel| 56 Channel
Positioning Accuracy| 10m
Hot start| 1s on average
Warm start| 15s on average
Cold start| 30s on average
Working temperature| -20°C to 55°C
Humidity| 5%~95% non-concretion
Antenna| Built-in 3G/GPS antenna
Sensor| 3D acceleration sensor
LED| 3G/GPS/CHG
SIM Card interface| Standard SIM Card
Hardware description
4.1 Appearance
First use
5.1 SIM Card installation
Pay attention to the following items before installing the SIM card:
- Ensure the SIM card have enough balance
- Ensure the SIM card enable caller ID and GPRS function
- Ensure the SIM card disable PIN password and call forwarding function.
Install the SIM card
- Get ready a Standard SIM Card
- Insert the SIM Card to the slot
Pay Attention:
- Device will POWER ON automatically after insert the SIM card
5.2 Indications
5.2.1 3G Indicator (Blue)
Status | Description |
---|---|
Always ON | No SIM Card or no network |
Slow flash (8s/time) | Work mode |
5.2.2 GPS Indicator (GREEN)
Status | Description |
---|---|
Always OFF | GPS unavailable |
Quick flash (1s/time) | GPS available |
5.2.3 Charge Indicator (YELLOW/RED)
Status | Description |
---|---|
Always ON(Yellow) | Under charging |
Light bright(Yellow) | Changing completed |
Slow lash(Red) | Low battery |
5.3 Device Button Instruction
Button | Description |
---|---|
Power Button | • Insert the SIM card to POWER ON, take out SIM card to |
POWER OFF.
SOS Button| • Press and hold button for 3 seconds(vibrate twice), the unit
will call the authorized phone numbers by sequences and send position to
authorized phone numbers and upload data to server.
• Short press button for 1 second(vibrate one time) to hang up/Answer or the
call(incoming or Speaking)
Main Operation and Application
6.1 Set Authorization Phone Number
Instruction format: cell phone number password*serial number(1-3)*
For example:1342439233000001
Reply: SET USER NUMBER 1 OK.
Note:**
- The defaulted password is 0000
- It can authorize up to 3 phone numbers.
6.2 Delete authorization number
Instruction format: passwordnumber(1-3)
For example: 00001
Reply: DELETE USER NUMBER 1 OK.
6.3 Change the password
Instruction format: 777+new password+old password
For example: 77712340000
Reply: SET USER PASSWORD OK.
6.4 Single Locating
Instruction format: 666+password
For example: 6660000
Description: Send this SMS command to unit,it will reply SMS as follow:
ID: 865662000409210
Date: 05:36:59 15/08/2015
Fix:A State: SMS
http://maps.google.com/maps?q=+22.63146%2c1+114.03701
6.5 Calling Switch
Calling OFF: 150+password
For example: 1500000
Reply: SET VOICE CALL:OFF
Calling on: 151+password
For example: 1510000
Reply: SET VOICE CALL: ON
Note: if you do not want to get the Calling alert, send 1500000 to
disable it.
6.6 SMS Response ON/OFF
SMS OFF: 160+ user password
For example: 1600000
Reply: SET SEND SMS:OFF.
SMS ON: 161+ user password
For example: 1610000
Reply: SET SEND SMS:ON.
Note:
- If you do not want to get the SMS alert, send 1600000 to disable it.
6.7 Call Restriction Switch
Call restriction OFF: 170+password
For example: 1700000
Reply: SET INCOMING CALLS:OFF.
Call restriction ON: 171+password
For example: 1710000
Reply: SET INCOMING CALLS : ON
Note:
- 170 mode,it can only receive incoming call from 3 authorization numbers.
- 171 mode the device can answer incoming call from any cell phone.
6.8 Phone positioning function
If incoming call is from one of the 3 authorized numbers and it is hung up
after ringing for 2-5 times, the device will send location to authorized phone
number and then upload data to server and the status is :CALL.
6.9 SOS Alarm
Press SOS button for 3 seconds(vibrate twice),device will call the authorized
phone numbers and then send location to authorized phone number and upload
data to server,the state is: SOS.
6.10 Voice Monitor
Disable the monitor : 000+password
For example: 0000000
Reply: SET VOICE MONITOR:OFF.
Enable the monitor : 001+password
For example: 0010000
Reply: SET VOICE MONITOR:ON.
Note: Default is MONITOR OFF
6.11 Round Geo-fence
Instruction format: 005+password+R+X
For example: 0050000R1.0
Reply: SET ROUND GEO-FENCE:ON
Note: X define[0.1-999.9]KM
6.11.1 Enable the Geo-fence
Instruction format: 211+password
For example: 2110000
Reply: SET ROUND GEO-FENCE: ON.
6.11.2 Disable the Geo-fence
Instruction format: 210+password
For example: 2100000
Reply: SET ROUND GEO-FENCE: OFF.
6.12 Square Geo-fence
Instruction format:006+password+G1,IO/I/O,E/W longitude upper limit+N/S
latitude upper limit,E/W longitude lower limit+N/S latitude lower limit.
For example:0060000G1,IO,E114.04540N22.59034,E114.05978N22.59797
Reply: SET SQUARE GEO-FENCE1(IO)OK.
6.12.1 Enable the Geo-fence
Instruction format: 311+password
For example: 3110000
Reply: SET SQUARE GEO-FENCE: ON.
6.12.2 Disable the Geo-fence
Instruction format: 310+password
For example: 3100000
Reply: SET SQUARE GEO-FENCE: OFF.
6.13 Low battery Alarm
When the backup battery is low power,it will send SMS to authorized phone
number and upload data to server, the state is:BLP.
6.14 Over-speed alarm
Command: #122#user password#X##
Example: #122#0000#100##
Reply: SET SPEED LIMIT:ON
Close command: #122#0000#0##
SET SPEED LIMIT: OFF.
Note: X is speed value, unit is KM/H definition is [0, 999].
6.15 Set time zone
Instruction format: 896+password+ +/-HH:MM
For example: 8960000+08:00
Reply: SET TIME ZONE:+08:00
Note: The default is Greenwich time(UTC).
6.16 Set GPRS user name
Instruction format: #801#password#user name##
For example: #801#0000#MT500##
Reply: SET SERVER USER NAME OK.
6.17 Set APN(Access Point Name)
Instruction format 1: #803#user password#APN##
For example: #803#0000#CMNET##
Instruction format 2: #803#password#APN#APN user name# APN password##
For example: #803#0000#CMNET#INTERNET#INTERNET##
Reply: SET GPRS APN OK.
Note: please contact your local mobile operator to get the correct APN.
6.18 Set Server IP and PORT
Instruction format: #804#password#IP address(or domain) #port##
Example: #804#0000#112.95.164.248#7780##(or)
804#0000#e.trackits.com#7700##
Reply: SET SERVER IP AND PORT OK.
6.19 Set GPRS Upload Interval Time
Instruction format: #805#password#interval time#X##
For example: #805#0000#10#1##
Reply: SET GPS PERIODIC UPLOAD ON.
Note: interval time define is[10,65535]seconds, X define is[0,1], If
X=0,it will stop upload and reply: SET GPS PERIODIC UPLOAD OFF.
6.20 Power Saving Mode
Enable power save mode : 100+password
For example: 1000000
Reply: SET POWER SAVE MODE:ON.
Disable power save mode : 101+password
For example: 1010000
Reply: SET POWER SAVE MODE:OFF.
Note: Default is OFF
6.20.1 Power Saving Mode ON & Device Stop interval time
Instruction format: #807#password#interval time##
For example: #807#0000#2##
Reply: SET GPS POWER SAVING UPLOAD ON.
Note:
- Interval time define is [2,1440] minuets,If interval time is 0, it will stop upload and reply: SET GPS POWER SAVING UPLOAD OFF.
- If you enable power saving mode(1000000) and device is stop, the device will upload will as 807 command interval.
- Upload status is AUTOLOW
6.20.2 Power save mode ON &device Move interval time
Instruction format: #809#password#interval time#X##
For example: #809#0000#10#1##
Reply: SET GPS TOWED UPLOAD ON.
Note:
- Interval time define is[10,65535]seconds, X define is[0,1], If X=0,it will stop upload and reply: SET GPS TOWED UPLOAD OFF.
- If you enable power saving mode(1000000) and device is move, the device will upload will as 809 command.
- Upload status is TOWED
6.21 Invalid GPS Data Upload
Invalid data upload ON: 081+users password
For example: 0810000
Reply: INVALID DATA UPLOAD:ON
Invalid data upload OFF: 080+user password
For example: 0800000
Reply: INVALID DATA UPLOAD:OFF
6.22 Mileage report
6.22.1 Set report interval time
Format: #141#password#X#Y##
For example: #141#0000#10#1##
Reply: SET GPS MILEAGE STATISTICS:ON/OFF
Note: X is the mileages and define is [0,1000]KM;
Y is alert mode and define is[0,1],Y=0 disable the alert, Y=1 enable alert.
6.22.2 Clear the Mileage
Format: #142#password#T##
For example: #142#0000#1##
Reply: SET GPS MILEAGE STATISTICS:CLEAR CURRENT/ALL
Note: T is [0,1].T=0,clear current mileage;T=1,clear total mileage.
6.22.3 Check the current mileage
Format: #143#password##
For example: #143#0000##
Reply: TOTAL GPS MILEAGE:X.X Km
CURRENT GPS MILEAGE: X.X Km
Note: mileage unit is KM
Tips:
- How to setup APN: https://www.mictrack.com/apn-settings-for-mictrack-gps-trackers
- How to use Mictrack Server: https://www.mictrack.com/how-to-use-mictrack-server
- Global Frequency bands check: https://www.mictrack.com/4g-lte-frequency-bands-list
Note: Please remember to monitor the credit balance of your SIM card, to
avoid confusion or delays in setting up your new unit. This can be a common
issue, especially when initially setting up a new unit, and the unit fails to
reply to a correct SMS command sequence.
If you have any questions please do not hesitate to contact us
info@mictrack.com.
http://www.mictrack.com
https://manual-hub.com/
References
- Ultra Low Power Asset Tracking Device Manufacturer
- Manual-Hub.com – Free PDF manuals!
- How to Use Mictrack Server - Mictrack
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>