mictrack MP90 4G OBD Tracker User Manual
- June 5, 2024
- mictrack
Table of Contents
mictrack MP90 4G OBD Tracker
Preface
Congratulations on choosing Mictrack MP90 4G OBD GPS tracker. This manual shows how to easily program and set up the tracker for the best results. Make sure to read this manual carefully before using this product, so as to avoid delays or confusion with its operation. Please note that specifications and instructions are subject to change without notice to facilitate product improvement. Updates and changes will be integrated into the latest release. The manufacturer assumes no responsibility for any errors or omissions in outdated documents.
Overview
The MP90 is a plug-and-play 4G OBD tracker without wiring. Easy install to any vehicle with a standard OBD II connector. It can be used to locate, track and monitor the vehicle via SMS, PC Computer or Mobile APP. It is commonly used to track and locate individual vehicles, the user also can real time track and check the historical route traveled.
Application
- 4G LTE network support(can fall back to 3G/2G)
- OBD II connector easy to install (Plug and Play)
- Real-time position acquiring
- Vehicle trip history and mileage data on web tracking platform
- Geo-Fence alarm and reporting
- Vehicle towing / Movement alarm
- Over-Speed alarm and reporting
- Remove and disconnect alarm
- Backup battery low power alarm
- Power saving/sleep mode
- Mileage report
- Compatible with most of third-party platform
- Open protocol
Specifications
Item
| Specifications
---|---
Dimension| 67(L)50(W)25(H)mm
Weight| 65g
Input Voltage| 12V-24VDC
Backup battery| 3.7 V 120 mAh; 50mA standby current at 12 V
Power consumption| 50mA standby current at 12 V
Working temperature| -20°C to 55°C
Humidity| 5%~95% non-concretion
Working hour| 2 hours in power-saving mode, 0.5 hours in normal mode
LED indicator| 4G(RED),GPS(BLUE)
Sensor| 3D acceleration/movement sensor/ temperature sensor
Antenna| Internal 4G & GPS antennas
GPS Sensitivity| -162dBm
Item
| Specifications
---|---
Positioning Accuracy| 5-10m
Cellular Frequency bands
| MP90-E (Asia/Europe/Africa) 4G LTE: B1/B3/B7/B8/B20/B28A
3G WCDMA: 900/2100MHz
2G: 900/1800MHz
MP90-A (US/CA/Mexico) 4G LTE: B2/B4/B12
3G WCDMA: 850/1700/1900MHz
MP90-AU (Australia/New Zealand)
4G LTE: B1/B2/B3/B4/B5/B7/B8/B28/B40
3G WCDMA: 850/900/1900/2100MHz
2G :850/900/1800/1900MMz
MP90 interface
Installation
SIM Card installation
To install the SIM card, perform the following operations:
- Gently open the back case using screwdrivers((Diagram #1).
- Take out the over and First Insert the SIM card to the SIM card slot(Diagram #2)
- Second, Insert the battery wire to the connector
- Attach back housing cover
- Device is ready
Note: The device only supports a Micro Size SIM card.
Install the Device
- Directly insert the ODB tracker to vehicle’s OBD2 interface
LED Indications
SYS-System indicator (RED)
Status
| ****
Description
---|---
Always-ON| No SIM Card (or) No Network Reception
Quick flash| Access network successful
GPS-GPS indicator (BLUE)
Status
| ****
Description
---|---
OFF| GPS / Satellites Unavailable – Out of Range
Blinking| GPS/Satellite Locked – Normal Mode
Setup and Configuration
Note: When sending an SMS command to the unit, do NOT use spaces or symbols not listed below. [brackets and + are for instructional use only] * and # are valid command parameters. Following a successful command, you should always receive a reply SMS from the unit. Be patient, as this may take some time depending if the unit is required to reboot to process the command. Failure to reply will indicate either an incorrect SMS Command or the unit has powered off, lost a GSM Mobile signal or run out of SIM Card credit.
Setting Authorized Mobile Phone Numbers
- SMS Command format: mobile number+password+[command parameter]
Note: Command Parameter here is the sequence of the mobile number i.e. [1=Admin] or [2=SOS call number]
- For example: 134243923300000*1**
- Unit Reply: SET USER NUMBER 1 OK.
Note
- The defaulted password is 0000.
- It can authorize up to 3 phone numbers.
Deleting authorized number
- SMS Command format: password+number+[command parameter]
Note: Command Parameter here is the sequence of the mobile number i.e. [1=Admin] or [2=SOS call number]
- For example: *00001**
- Unit Reply: DELETE USER NUMBER 1 OK.
Changing the Admin password
- SMS Command format: 777+new password+old password
- For example 77712340000
- Unit Reply: SET USER PASSWORD OK.
Instant Location Request (used to receive unit location via SMS)
SMS Command format: 666+password
For example 6660000
When sent, this command will result in a Unit Reply SMS as follows:
- ID: 861108030047996
- Date: 06:39:02 14/03/2017
- Fix: A State:SMS
- http://maps.google.com/maps?q=+22.63146%2c+114.03701
Note: This link can to be opened on any Smart Phone to reveal the Google Maps Location of the unit at the time of the request.
Instant Location Request (Phone Call Activated)
If the unit receives an incoming call from one of it’s 3x authorized numbers, and the call is hung up after ringing only 2-5 times, the device will send an SMS containing it’s location to it’s authorized phone number, and then upload it’s location data to the Web Tracking Platform server along with the status description “CALL”
Round Geo-fence (Setting of size and shape of Geo-Fence)
- SMS Command format: 005+password+R+[Command Parameter]
Note: Command Parameter here is fence diameter in KM [0.1~999.9]
- For example: 0050000R1.0
- Unit Reply: SET ROUND GEO-FENCE:ON
Un-plug alarm
If the MP90 was removed from the OBD connector, it will call the authorized phone numbers, and then send location data to the authorized phone number and upload location data to the Web Tracking Platform server along with the status description “DEF”
Low battery Alarm (internal backup battery)
When the unit’s internal backup battery is low, it will SMS the authorized phone number, and upload location data to the Web Tracking Platform server along with the status description “BLP”
Over-Speed alarm (Alerts that the unit is exceeding a preset speed)
-
SMS Command format: #122#user password#[Command Parameter] Note: Command Parameter here is [Km/Hour]
-
Example: #122#0000#100 * Unit Reply: SET SPEED LIMIT: ON
-
To disable the Over-Speed Alarm
-
SMS Command format: #122#0000#0 Note: Command Parameter here is [0=OFF]
-
Unit Reply: SET SPEED LIMIT: OFF.
Note
- Speed is in KM/H, Maximum setting = [999].
- Maximum 10 Characters
Set APN (Access Point Name)
- SMS Command format 1: #803# password#APN For example: #803#0000#telstra.internet SMS Command format 2: #803#password#APN#APN user name# APN password For example: #803#0000#CMNET#INTERNET#INTERNET Reply: SET GPRS APN OK.
Note: please contact your SIM Card provider to get the correct APN
details
(Most SIM Card GSM providers do not use passwords or usernames for access – it
is already encoded into the SIM Card)
Set Tracking Server IP and PORT
- SMS Command format: #804#password#IP address(or domain) #port Example: #804#0000#e.trackits.com#7700 Reply: SET SERVER IP AND PORT OK.
Set the Upload Interval Time (Normal mode)
-
SMS Command format: #805#password#interval time#[command parameter] Note: Command Parameter here [1=ON] & [0=OFF]
-
For example: #805#0000#10#1 * Unit Reply: SET GPS PERIODIC UPLOAD ON.
Note: interval time maximum [10,65535]seconds.
- Unit Reply: SET GPS PERIODIC UPLOAD OFF.
Power Saving Mode
- Enable power save mode: 100+password
- Example: 1000000
- Reply: SET POWER SAVE MODE:ON.
- Disable power save mode: 101+password
- Example: 1010000
- Reply: SET POWER SAVE MODE:OFF.
Note: Default is OFF
Power Saving Mode & Device Stationary
- SMS Command format: #807#password#interval time * For example: #807#0000#2 Note: Interval time defined is [2,1440] minuets,If interval time is 0, it will stop upload and reply: SET GPS POWER SAVING UPLOAD OFF. If you enable power saving mode(1000000) and the device is stopped, the device will upload will as 807 command interval. Upload status is AUTO LOW.
Power save mode ON&device Move interval time
- Command: #809#password#interval time#X Example: #809#0000#10#1 Reply: SET GPS TOWED UPLOAD ON.
Note
- Interval time define is[10,65535]seconds, X define is[0,1], If X=0,it will stop upload and reply: SET GPS TOWED UPLOAD OFF.
- If you enable power saving mode(1000000) and the device is moved, the device will upload will as 809 commands.
- Upload status is TOWED
SMS Response ON/OFF
- To turn SMS messages OFF
- SMS Command format: 160+password
- For example 1600000
- Unit Reply: SET SEND SMS:OFF.
- To turn SMS messages back ON
- SMS Command format: 161+password
- For example 1610000
- Unit Reply: SET SEND SMS: ON.
Note: if you want to disable the SMS alerts, send 1600000
Unit Phone Calling Control (useful for SIM Card data cost saving)
- To turn OFF unit Calling Alerts (i.e. to save SIM data costs)
- SMS Command format: 150+password
- For example 1500000
- Unit Reply: SET VOICE CALL: OFF
- To turn ON unit Calling Alerts
- SMS Command format: 151+password
- For example 1510000
- Unit Reply: SET VOICE CALL: ON
App & PC Tracking platform
Active the device ID number
- Contact your sales or distributor
- If not please subscribe to the server plan from the official online shop:
- https://shop.mictrack.com/product/gps-tracking-platform-service/
App install & Login
- Search “Yi tracker” in Google Play or iOS store(or scan the following QR code) to download the Mobile APP(not Yi tracker2);
- Choose the” Login by Device No., Input server www.trackits.com
- Input your device’s ID number and password(default is 123456) to log in.
PC login
- Web: www.trackits.com, Choose “ID No.”
- Input your device’s ID number and password(default is 123456) to log in
- Watch the video: https://bit.ly/trackis
Troubleshooting
Issues | Caused | Solutions |
---|
Send SMS to the device but no reply
| 1>SIM Card have not active 2>Card balance is not enough| Please check the SIM card status and try again.
The text command format is wrong
| Please check the command format again
| ****
Connect network fail.
| Please check LED status and make sure the network
connect successfully first.
---|---|---
GPS platform shows logged off| |
- Check the APN setting ;
- Check IP and port
- Check the network if matches
GPS platform shows no location or the coast of
Africa.
| Device indoor/garage| Take it outside for a
10-minute walk or drive, and its location should update.
LED no light| The backup battery is low power| Please charge the device for 30 minutes at least.
Any questions please do not hesitate to contact us:
- Add: 706, United Building, Donghuan 1st Road, Longhua District, Shenzhen, China 518109
- Tel: +86-755-28198746
- Web: www.mictrack.com
- Email: info@mictrack.com
References
- Ultra Low Power Asset Tracking Device Manufacturer
- YouTube
- GPS Tracking Platform Service - Mictrack Shop
- Ultra Low Power Asset Tracking Device Manufacturer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>