mictrack B22 OBD GPS Tracker User Manual

mictrack B22 OBD GPS Tracker

Overview

• B22 OBD tracker is a small GPS tracking device that plugs directly into the OBD port of any vehicle.
• No tools or wiring required. Simply plug the device into the car’s OBD port.
• It can be used to track the vehicles via PC or Mobile App, and also monitor vehicle data such as fuel consumption, rapid acceleration or deceleration, etc.

Application

• Driving Behavior Monitoring
• VIN Detection
• Real-time tracking
• Vehicle vibrate alarm
• Geo-Fence
• Disconnect alarm
• ACC Monitoring
• Over-Speed alarm
• Vehicle Crash alert
• Low battery alarm
• Mileage statistics
• History record playback
• OTA

Specifications

ISO14230 ISO15765

Power consumption| 10mA standby current
GPS Chip| U-BLOX7
GPS Sensitivity| -162dBm
Channel| 56 Channel
Positioning Accuracy| 10m
Item| Specifications
---|---
Hot start| 1s on average
Warm start| 15s on average
Cold start| 30s on average
Working temperature| -20°C to 60°C
Humidity| 5%~95% non-concretion
Antenna| Internal GSM & GPS antennas
Sensor| 3D G-sensor
SIM Card interface| Micro Size SIM

B22 interface

• Standard 16PIN OBD2 interface
• Built-in GPS & OBD module
• Insert the SIM card into the SIM card slot.
• Attach back the housing.
• Directly insert the ODB tracker into the vehicle’s OBD2 interface.

Installation

SIM Card installation

• Please read the following before installing the SIM card:
  • Ensure the SIM card has a balance
  • Ensure the SIM card has caller ID and GPRS functions enabled
  •  Ensure the SIM card PIN is disabled
• To install the SIM card, perform the following operations:
  • Gently open the case using a screwdriver.
  • Insert the SIM card into the SIM card slot.
  • Attach back the housing.
  • Directly insert the ODB tracker into the vehicle’s OBD2 interface.

Note:

• The device only supports Micro Size SIM cards;

LED Indications
GSM indicator (RED)

GPS indicator (BLUE)

Setup and Configuration

Note : All the end of SMS command is ‘;’

Monitor (optional)

• Format: AS7777AT+AUTHNUMBER=number 1, number 2, number 3;
• Example: AS7777AT+AUTHNUMBER=13424392330,,;
• Reply: +AUTHNUMBER:13424392330,, OK
• Note: This function is optional.

Set IP and Port

• Format: AS7777AT+MSERVER=IP,Port,1;
• Example: AS7777AT+MSERVER=47.91.230.66,7018,1;
• Reply: +MSERVER:47.91.230.66,7018,1 OK
• Note: support the IP and domain.

Set APN

• Format: AS7777AT+APN=APN,USER,Password;
• Example: AS7777AT+APN=cmnet,,;
• Reply: +APN:cement,, OK
• Note: Please CALL your sim card provider to get the correct APN

Setup Timezone

• Format: AS7777AT+TIMEZONE=time zone;
• Time zone= E[0~12] or W[0~12]
• Example: AS7777AT+TIMEZONE=E8;
• Reply: +TIMEZOONE:E8 OK

Setup Over speed

• Format: AS7777AT+LIMITSPEED=Speed Value;
• Example: AS7777AT+LIMITSPEED=100;
• Reply: +LIMITSPEED:120,100 OK
• Note: The speed value must be over 100

Configure:

• Format: AS7777AT+CONFIG=SN0147.91.230.6617018cmnet13184210052E810 503051360*;
• RE: CONFIG:<SN0147.91.230.6617018cmnet1318421002E810503051360> OK

Check the Config:

• Format: AS7777AT+CONFIG;
• Reply: +CONFIG:<SN0147.91.230.6617018cmnet13184210052E810503051360*>
• Restart:
  • Format: AS7777AT+RESET;
  • Reply: OK

APP & PC tracking platform

Subscribe to the server plan

• Contact your sales or distributor to active your device
• Subscribe to the server from our official shop: https://www.mictrack.com/shop/gps-tracking-platform-service.

App install & Login

• Scan the following QR code to download the App
• Choose English server
• Input username(or device ID)and password(default is 123456) to log in.

PC login

• Web: http://gps.mictrack.com.
• Choose “Plate No./IMEI”
• Input your device’s ID number and password(default is 123456)

Real-time tracking

• On the GPS, you will track the vehicle in real-time, it will show the position and status as below.
• The OBD data will be reported to the server while the engine is on, and then you can get OBD information on the tracking system, Click [OBD], it will show the detail of OBDII information, as below.
• Vehicle VIN Host reads and uploads the vehicle VIN when the vehicle starts.
• OBD2 Standard fault code Read vehicle Standard fault code and report.
• OBD2 Standard data stream
• Engine speed, vehicle speed, battery voltage, throttle opening, engine load, coolant temperature, instantaneous fuel consumption, average fuel consumption, mileage, total mileage, fuel consumption, cumulative fuel consumption, the current number of fault codes, the number of acceleration, the number of slowdowns and so on.
• Note: it is based on the vehicles, some vehicle models do not support the sensors, so cannot get the data via OBD devices.

History playback

The GPS tracking system will save the history data, you can easily playback the history.

Vehicle moving detection

The G-Sensor real-time detects the vehicle status, such as illegal vehicle movement, vehicle collision, etc.
Driving behavior analysis

• Accumulated travel time/current driving time
• Accumulated idle time/The idling time
• Average speed
• The highest speed in history / the highest speed
• Cumulative number of rapid acceleration
• Mileage
• This time driving fuel consumption
• The idle fuel consumption

Note: Please remember to monitor the credit balance of your SIM card, to avoid confusion or delays in setting up your new unit. This can be a common issue, especially when initially setting up a new unit, and the unit fails to reply to a correct SMS command sequence. If you have any questions please do not hesitate to contact us at [email protected]. https://www.mictrack.com.

References

• gps.mictrack.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>