mictrack MT700 Cat M1 and NB IoT Asset GPS Tracker User Manual

MT700 Cat M1 & NB-IoT Asset GPS Tracker
User Manual V1.0

Preface
Thanks for purchasing the Mictrack Asset GPS tracker MT700. This manual shows how to easily program and set up the tracker for the best results. Please read this manual carefully before using this product, so as to avoid delays or confusion with its operation. Please note that specifications and instructions are subject to change without notice to facilitate product improvement. Updates and changes will be integrated into the latest release. The manufacturer assumes no responsibility for any errors or omissions in outdated documents.

FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator& your body.

Quickly Reference

Warning
There is a Toggle Switch in the internal(following image). Please carefully operate it.

• If you use Non-rechargeable batteries, Make sure to Toggle Switch to LEFT;
• If you use chargeable batteries, Make sure to Toggle the Switch to the RIGHT;
• REVERSE IS FORBIDDEN, Could Result in Fire or Explosion.

Non-rechargeable Batteries Recommendation

• Battery Type: Lithium Iron Disulfide (LiFeSO2) 3 x AA 1.5V cell batteries;
• Battery Brand: Energizer Ultimate L91 AA 1.5V.
• Battery holder: Buy from the Manufacture or your distributor.

NOTE:

• Lithium Thionyl Chloride (LiSOCl2) 3 x AA 3.6V cell batteries are unavailable now, if need can customize the hardware, please contact us or your provider for more details.
• Non-rechargeable batteries need to be fully compatible with the original battery holder, or the device may cause damage, explosion, and fire.

Disclaimer
Before using this device, the customers should fully understand their usage scenarios and installation environment. Mictrack will not be held responsible for any losses caused by using the devices in the wrong scenario or reporting rate. It is highly recommended that users should contact Mictrack before deployment. We are glad to give you the suggestions.

Overview

MT700 is an IP68 waterproof asset GPS tracker that uses Cat M1 & NB-IoT technology that can provide super low power consumption of up to 15 years of standby time powered by internal batteries. Its built-in powerful magnets are easy to install without wiring.
The user can real-time track the unit via their mobile phone or PC at any time anywhere. It has been widely used in fleet management, trailer, container, logistics, car rental, automobile finance, transportation, and other segments.

Features

• Cat M1 & NB-IoT & GSM Network
• GPS+Glonass+Galileo+Beidou System
• 15 Years Standby Time
• IP68 Dust & Water Resistance
• Dynamic Power Path Management
• Ultra Low Power Consumption less than 1.5uA
• Easy Installation
• Powerful Magnet Mount
• Bracket Kits (optional)
• Rugged Construction| • Real-timing Tracking
• Geo-fence Alarm
• Low Power Alarm
• Removal Alerts
• Smart Motion Detection
• Scheduled Timing Report
• GPS+WiFi Positioning (optional)
• Multiple Power Saving Mode Switching
• PC & Mobile App Tracking
• Programmable via Web/USB/SMS
• Open Protocol & Easy Integration with any third-party platform
---|---

Applications

• Trailer Tracking
• Container Tracking
• Logistics Tracking
• Vehicles Tracking
• Automobile Finance
• Fleet Management

Specifications

Charging Mode

| Micro USB charging DC; Quick Charge 2A@5V

(for rechargeable version only)

Power Consumption| <1.5uA standby current (in lowest power configuration)
Backup Battery (Two versions)| Rechargeable 3.7V 7800mAh Li battery
Non-rechargeable LiFeS2 (batteries are exclude)
4G Cellular Bands| Cat M1 (LTE-M, eMTC) B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28/B39 NB-IoT (CAT NB1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28
GSM: 850/900/1800/1900Mhz
Working temperature| -20°C to 60°C (-4°F to 140°F)
Mounting| Magnet, Bracket Kits (optional)
Positioning| GPS, WiFi (optional)
GPS| Qualcomm Gen 8C GNSS receiver
GPS Antenna| Internal
Cellular Antenna| Internal
Sensor| 3-Axis Accelerometer, Light Sensor
LED| Charge/SYS/GPS
SIM Card interface| Internal Micro 3FF SIM
Protocol| TCP, UDP, SMS
Waterproof| IP68
Battery life| 15 Years
Antenna Max.PeakGain| WWAN Module Antenna Gain <4dBi

MT700 Interface

In the box

7.1 Standard Accessories

• 1* MT700 Asset GPS Tracker
• 1* USB Charge Cable (for rechargeable version only)
• 1* Battery Holder (for the Non-rechargeable version only)
•  1* Quick Start Guide

7.2 Optional Accessories

• 1* Car Charger
• 1* Power Adapter
• 1* USB Config Cable

Installation

8.1 SIM Card installation

• Get ready a Micro SIM Card (Cat M1 or NB-IoT) with 15MB of data a month;
• Open the Waterproof Cover with the screwdriver;
• Insert SIM Card with a little push (as SIM icon direction), or watch the video http://bit.ly/MT700-Install-Guide
• Turn the Power button from OFF to ON.

8.2 LED Indications
8.2.1 Red indicator- Charge

8.2.2 Blue indicator- SYS

8.2.3 Green indicator- GPS

Setup and Configuration

• For the first-time to use, please connect the USB Config cable to setup the APN (CALL your sim card provider to get the correct APN) and then lock the network(base on your sim card support, please lock to CAT M1 or NB-IoT) ;
• After that you can set up other commands via the USB Config tool;
• If your sim card support SMS you can set up the unit via the following SMS commands (9.1-9.12)
• Download the USB Config tool from the link: https://bit.ly/MT700-Config-tool
• Config tool user guide video: https://bit.ly/MT700-Config-Tool-User-Guide

9.1 Change the password
SMS Command format:777+new password+old password
For example:77712340000
Reply: SET USER PASSWORD OK.
Note: The default password is 0000

9.2 Set APN (Access Point Name)
SMS Command format 1: #803#password#APN##
For example : #803#0000#nbiot##
SMS Command format 2: #803#password#APN#APN user name#APN password##
For example: #803#0000#CMNET#INTERNET#INTERNET##
Reply: SET GPRS APN OK

9.3 Set the IP and port
SMS Command format : #804#password#IP address(or domain) #port##
For example : #804#0000#e.trackits.com#7700##
Reply: SET SERVER IP AND PORT OK.

9.4 Working Mode
9.4.1 MODE 1 (Real Time Mode)
SMS Command format: MODE,1,password,T
For examples: MODE,1,0000,60
Reply: SET TRACKER MODE:1 OK
Note: The device will report data every 60s .T is interval time and the range is [60-600] seconds. On this mode, GPS and TCP will always on

9.4.2 MODE 2 (GPS Auto Mode)
SMS Command format: MODE,2,password,T, X, Y
For examples: MODE,2,0000,10,1,1
Reply: SET TRACKER MODE:2 OK

Note:

1. T is the report interval time and the range is [10,60] minutes.
2. X=0 means GPS will wake up only when the report interval time arrives; X=1 means GPS will always be on,
3. Y=0 means TCP will wake up only when the report interval time arrives; Y=1 means TCP will always be connected,.

9.4.3 MODE 3 (Deep Sleep Mode)
SMS Command format: MODE,3,password,T
For examples: MODE,3,0000,1
Reply: SET TRACKER MODE:3 OK
Note: The device will wake up and report data to the server every 1 hour, after that it will go to sleep again until the next 1 hour. T is [1-24] hours.

9.4.4 MODE 4 (Vibrate Mode)
SMS Command format: MODE,4,Password,T
For examples: MODE,4,0000,60
Reply: SET TRACKER MODE:4 OK
Note: When the device detects continuous vibration for more than 1 minute, it will wake up and starts to connect to the network, After connected it will Immediately report data to the platform;
If the device is still in a vibrating state, MT700 will report to the server every 60 seconds
If there is no vibration for more than 7 minutes:
1>During In the 7 minutes if no report data it will go to sleep soon.
2>During In the 7 minutes if have report data and after sending out the last location, it will wait for 3 minutes and then go to sleep again. T is [60-600] seconds

9.4.5 MODE 5 (WiFi Only Mode)
SMS Command format: MODE,5,password,T, X, Y
For examples: MODE,5,0000,5,0,1
Reply: SET TRACKER MODE:5 OK

Note:

1. T is the report interval time and the range is [1,60] minutes.
2. X fix to 0.
3. Y=0 means TCP will wake up only when the report interval time arrives; Y=1 means TCP will always be connected.

9.4.6 MODE 0 (AUTO Mode)
SMS Command format: MODE,0,T1,T2
For examples: MODE,0,60,1
Reply: SET TRACKER MODE:0 OK
Note: This is a mixed mode of Mode 3 and mode 4. T1 is [60-600] seconds, T2 is [1-24] hours; When the device is still it will run as Mode 3 and when the device detects to vibrate it will run as Mode 4.

9.5 Setup Protocol
SMS Command format: #800#password#X##
For example: #800#0000#TCP##
Reply: SET SERVER TYPE OK
Note: X=TCP means setup to TCP protocol, X=UDP means set to UDP Protocol.

9.6 SET AGPS
Disable AGPS Location:190+password
For examples:1900000
Reply: SET AGPS OFF
Enable the Last Location:191+password
For examples:1910000
Reply: Reply: SET AGPS ON.

9.7 Setup Last location report
Disable the Last Location:192+password
For examples:1920000
Reply: SET LAST VALID GPS OFF
Enable the Last Location:193+password
For examples:1930000
Reply: Reply: SET LAST VALID GPS ON.

9.8 Low Power Alarm
When the unit’s internal backup battery is low, it will upload location data to the server along with the status “BLP”

9.9 Remove alarm
If the device was removed and the light sensor detects the light it will report location data to the server along with the status “DEF”

9.10 Vibrate alarm
In vibrate mode (Mode 4) If the device was detected to vibrate for 1 minute, it will report location data to the server (as the customized interval time) along with the status “TOWED”

9.11 Restart
SMS Command format : RESTART#Password##
For examples:RESTART#0000##
The device will restart after sending this command.
Reply: DEVICE WILL BE RESTART.

9.12 Reset
SMS Command format : RESET#Password##
For examples:RESET#0000##
Reply: DEVICE WILL BE RESET.

App & PC Tracking platform

10.1 App install & Login

• Subscribe to the plan: https://shop.mictrack.com/product/gps-tracking-platform-service/
• if you have subscribed to the plan please ignore this step.
• Search “Yi tracker” in Google Play or iOS store(or scan the following QR code) to download the Mobile APP(not Yi tracker2);

http://onelink.to/cnyv8k

• Choose the” Login by Device No.,
• Input server www.trackits.com
• Input your device’s ID number and password(default is 123456) to log in.

10.2 PC login

• Web: www.trackits.com
• Choose “ID No.”
• Input your device’s ID number and password(default is 123456) to log in

Troubleshooting

card and will not reply to the NB-IoT SIM card
2>SIM Card has no active
3>Card balance is not enough| Please check the SIM card status and try again.
The text command format is wrong| Please check the command format again
Connect network fail.| Please check the LED status and make sure the network connects successfully first.
GPS platform shows logged off| | 1. Check the APN setting ;
2. Check IP and port
3. Check the network of matches
GPS platform shows no location or the coast of Africa.| Device indoor/garage| Take it outside for a 10-minute walk or drive, and its location should update.
LED no light| The backup battery is low power| Please charge the device for 30 minutes at least.

(End of this document)
Any questions please do not hesitate to contact us:
Add: 706, United Building, Donghuan 1st Road, Longhua District, Shenzhen, China 518109
Tel: +86-755-28198746
Web: www.mictrack.com
Email: info@mictrack.com
https://www.mictrack.com

References

• MT700 - Google Drive
• Ultra Low Power Asset Tracking Device Manufacturer
• MT700_Config_Tool_User_Guide - Google Drive
• YouTube
• GPS Tracking Platform Service - Mictrack Shop
• Ultra Low Power Asset Tracking Device Manufacturer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>