Miele G800, G1000 and G2000 Series Waterproof System Installation Guide
- June 3, 2024
- Miele
Table of Contents
G800, G1000, and G2000 Series Waterproof System
Installation Guide
Installation
The Miele Waterproof system
Provided that your dishwasher has been installed correctly, the Miele
Waterproof system will protect you from water damage throughout its lifetime.
Water inlet
Health risk due to wash water. The water in the dishwasher is not drinking
water.
Do not drink any water from the dishwasher.
Health risk and risk of damage due to contaminated incoming water. The quality
of the incoming water must correspond to the drinking water specification of
the country in which the dishwasher is being operated.
Connect the dishwasher to a drinking water supply.
The dishwasher may be connected to cold or hot water (up to max. 60 °C)
supplies.
If energy-saving water heating sources such as solar energy circulation
systems are used, we recommend connecting to the hot water supply. This saves
both time and electrical energy costs. Hot water is used in all programs.
The water inlet hose is approx. 1.5 m long. A 1.5 m long, flexible metal
extension hose (tested to 14,000 kPa/140 bar) is available as an optional
accessory from Miele specialist dealers or the Miele Customer Service
Department.
A stopcock with a ¾” threaded union is required for the connection. If a
stopcock is not available, only a qualified installer may connect the
dishwasher to the drinking water supply.
The water connection pressure must be between 50 and 1000 kPa. If the water
connection pressure is too high, a pressure-reducing valve must be fitted.
Risk of damage from leaking water.
The connection point is subject to mains water pressure. Water leaking from it
can cause damage.
You should therefore open the stopcock slowly and check for leaks. Correct the
position of the seal and screw thread if appropriate.
Regulation in Germany
For the protection of drinking water, the non-return valve supplied with the dishwasher must be installed between the stopcock and the water inlet hose.
- Screw the non-return valve onto the stopcock.
- Screw the water inlet hose onto the thread of the non-return valve.
Risk of damage due to excessive pressure.
A brief increase in the water pressure can damage the components of the
dishwasher.
This dishwasher must only be operated when it is connected to a fully vented
plumbing system.
Risk of electric shock from mains voltage.
There are electrical components in the water inlet hose.
The inlet hose must not be shortened or damaged in any way (see illustration).
Water drainage The dishwasher’s drainage system is fitted with a non-return
valve, which prevents dirty water from flowing back into the appliance via the
drain hose.
The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an
internal diameter of 22 mm.
The drain hose can be extended using a connection piece to attach a further
length of the hose. The drainage length must not be longer than 4 m and the
delivery head no higher than 1 m.
If the hose is to be directly fitted to the drainage outlet on-site, use the
hose clip supplied (see installation plan).
The hose can be directed to the left or right of the appliance.
The on-site connector for the drain hose can be adapted to different hose
diameters. If the connector extends too far into the drain hose, it must be
shortened. Otherwise, the drain hose can become blocked.
The drain hose must not be shortened.
Lay the drain hose so that it does not kink and is not subjected to pressure
or tension.
Risk of damage from leaking water.
Leaking water can cause damage. After commissioning, make sure that the water
is not leaking.
Venting the water drain
If the on-site drainage connection is situated lower than the guide path for
the lower basket rollers in the open door, the drainage system must be vented.
Otherwise, a siphoning effect during a program can cause the appliance to
empty itself of water.
-
Open the dishwasher door fully.
-
Remove the lower basket.
-
Insert a screwdriver into the middle opening of the vent valve in the left wash cabinet wall 1.
-
Press the screwdriver further into the opening and push it through membrane 2 behind.
The vent opening for the water drain is now open.
Electrical connection
The dishwasher is “connector-ready” as the standard for connection to an
earthed socket.
The socket must be easily accessible after the dishwasher has been installed.
If that is not possible, ensure that a suitable means of disconnection is
provided on the installation side for each pole.
Risk of fire from overheating. Connecting the dishwasher to a multi-socket
adapter or to an extension lead can overload the main connection cable.
For safety reasons, do not use an extension lead or multi-socket adapter.
The electrical installation must comply with VDE 0100 requirements.
For safety reasons, we recommend using a type of residual current device (RCD)
in the assigned electrical installation for connecting the dishwasher.
If the mains connection cable is damaged, it must only be replaced with a
specific mains connection cable of the same type (available from the Miele
Customer Service Department). For safety reasons, such replacement may only be
carried out by a qualified specialist or the Miele Customer Service
Department.
These operating instructions and the data plate indicate the nominal power
consumption and the appropriate fuse rating. Compare this information with the
data of the on-site electrical connection.
If in any doubt, consult a qualified electrician.
Temporary or permanent operation on an autonomous power supply system or a
power supply system that is not synchronized with the mains power supply (e.g.
island networks, backup systems) is possible. A prerequisite for operation is
that the power supply system complies with the specifications of EN 50160 or
an equivalent standard. The function and operation of the protective measures
provided in the domestic electrical installation and in this Miele product
must also be maintained in isolated operation or in operation that is not
synchronized with the mains power supply, or these measures must be replaced
by equivalent measures in the installation. As described, for example, in the
current version of BS OHSAS 18001–2 ISO 45001.
11715540-04
Documents / Resources
|
Miele G800, G1000 and G2000 Series Waterproof
System
[pdf] Installation Guide
11715540-04, G800 G1000 and G2000 Series Waterproof System, G800 Series
Waterproof System, G1000 Series Waterproof System, G2000 Series Waterproof
System, G800, G1000, G2000, Waterproof System, Waterproof, Water Protection
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>