AiM Kit EVO4S, SOLO 2/SOLO 2 DL for Ducati Panigale V4/V2 User Guide

June 6, 2024
DUCATI

AiM Kit EVO4S, SOLO 2-SOLO 2 DL for Ducati Panigale- 2

AiM User Guide
Kit EVO4S, SOLO 2/SOLO 2 DL
for Ducati Panigale V4/V2
Release 1.04AiM Kit EVO4S, SOLO 2-SOLO 2 DL for Ducati Panigale-
LOGO

Models and years

This manual explains how to connect EVO4S/SOLO 2 DL to the bike engine control unit (ECU) and how to install AiM SOLO 2/SOLO 2 DL on the bike steering plate.
Compatible models are:

• Panigale V4 from 2018
• Panigale V2 from 2020

Warning: for these models/years AiM recommends not to remove the stock dash. Doing so will disable some of the bike functions or safety controls. AiM Tech srl will not be held responsible for any consequences that may result from the replacement of the original instrumentation cluster.

Kit contents and part numbers

AiM developed a specific installation bracket for SOLO 2/SOLO 2 DL and a connection cable to the ECU for EVO4S/SOLO 2 DL.

Bracket for SOLO 2/SOLO 2 DL

Part number for SOLO 2/SOLO 2 DL installation bracket for Ducati Panigale V4/V2 – shown below – is: X46KSTSDP.

AiM Kit EVO4S, SOLO 2-SOLO 2 DL for Ducati Panigale-
Bracket

Installation kit contains:
1 bracket (1)
2 allen screws with flat head M4x10mm (2)
1 washer (3)
1 rawl nut (4)
1 allen screw with rounded head M8x45mm (5)

AiM cable for SOLO 2 DL

Part number for SOLO 2 DL connection cable for Ducati Panigale V4/V2 – shown below – is: V02569170.

AiM Kit EVO4S, SOLO 2-SOLO 2 DL for Ducati Panigale- AiM
cable

Following image shows the cable constructive scheme.

Connection cable for SOLO 2 DL and installation bracket for Ducati Panigale V4/V2 can be bought together. Part number: V0256917CSP.

AiM cable for EVO4S

Part number for EVO4S connection cable for Ducati Panigale V4/V2 – shown below – is: V02585180. AiM Kit EVO4S, SOLO 2-SOLO 2 DL for Ducati
Panigale- Part number

EVO4S/SOLO 2 DL connection

To connect EVO4S/SOLO 2 DL to the bike ECU use the DDA connector placed under the bike tail and shown here below:
Open the bike tail and remove the cap from the DDA connector (shown on the right), then plug the specific AiM cable.

Configuration with Race Studio 3

Before connecting EVO4S/SOLO 2 DL to the bike ECU, set all functions using the AiM software Race Studio 3. The parameters to set in the AiM device configuration section are (“ECU Stream” tab):

• ECU Manufacturer: Ducati
• ECU Model: PANIGALE V4 for Ducati Panigale V4 (from 2018) and Ducati

Panigale V2 from (2020)

After this first selection, enable/disable the 120Ohm resistor and the “Silent” mode on CAN Bus as follows:

“Ducati – PANIGALE V4” protocol

Received channels by EVO4S/SOLO 2 DL configured with “Ducati – PANIGALE V4” protocol are:

CHANNEL NAME FUNCTION
RPM RPM
Gear Engaged gear
Speed Rear Rear wheel speed
Speed Front Front wheel speed
Lon Acc Longitudinal acceleration
Lat Acc Lateral acceleration
Roll Rate Roll rate
Pitch Rate Pitch rate
Yaw Rate Yaw rate
Engine Temp Engine coolant temperature
Intake Temp Intake air temperature
TPS Vert Vertical throttle position sensor
TPS Hor Horizontal throttle position sensor
Bike Angle Bike lean angle
Brake Front Front brake position
Twist grip Hand throttle position
Battery Volt Battery voltage
ShiftSw Shift switch
Trq Slow Torque slow
Trq Fast Torque fast
EBC ON Engine brake control ON
EBC Lv Engine brake level
DWC OFF Ducati wheelie control OFF
DWC Lv Ducati wheelie control level
DTC OFF Ducati traction control OFF
DTC Lv Ducati traction control level
DSC OFF Ducati slip control OFF
DSC Lv Ducati slip control level
EngineStatus Engine status
Eng St Engine status
Brake Switch Brake switch

Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals