GL-iNet XE300C6 4G LTE Wireless Router User Guide
- June 6, 2024
- GL iNet
Table of Contents
GL-iNet XE300C6 4G LTE Wireless Router
SETTING UP
Insert Cards & Power On
When powered up, your GL-XE300 router will broadcast Wi-Fi signal with the
SSID:
GL-XE300-xxx.
- Hot-plug for TF cards and Nano SIM cards are not supported for this router.
Connect via Wi-Fi
Connect to the Wi-Fi called GL-XE300-xxx, and input the default Wi-Fi password goodlife, which is also printed on the bottom of the router
Search the SSID and connect to it
Set up Router
Visit http://192.168.8.1 in your browser to set up your router; start by choosing your preferred language
Connect via LAN
Plug the cable connecting to your computer into LAN port
SUPPORT
Repair / Reset
If you cannot access the web-based setup page or cannot connect to the router,
you can press the Reset button:
Press and hold for 3 seconds, and then release to
repair your network.
Press and hold for 10 seconds, and then release to reset the router to factory
settings. All user data will ttps://docs.gl-inet.com/en/3/
Technical Supports
For more detailed and updated instructions, please visit our website docs.gl-
inet.com
For further questions, you can get help from the following ways:
- Email to [email protected]
- Message us on our Facebook: facebook.com/gl.inet.wifi/
- Post questions in our forum: forum.gl-inet.com
- Ask professionals in other forums e.g. OpenWrt, LEDE or other professional websites
WARRANTY
We provide one year limited warranty for routers and 3-month limited warranty
for accessories. Extra warranty may apply according to the local law in which
the product purchase took place. Highly recommend using the included 5V/2A
power adapter. Any damage to the router caused by not following the
instructions will render this warranty null and void. Any damage to the router
caused by modifying the PCBA, components or case will render this warranty
null and void. Issues caused by the use of third-party firmware may not get
official support from us. Any damage to the router caused by inappropriate
use, e.g. inappropriate voltage input, high temperature, dropping in
the water or on the ground will render this warranty null and void. Pictures
on the instructions are only for reference. We reserve the right to change or
modify these materials without further notice. Keep your device within the
recommended operating temperature (0°C to 40°C). Recommend storage temperature
for your device is between -20°C to +45°C. Please note lower or higher
temperatures may cause damage to the device. To avoid battery or device
failure, do not remove or replace the non-removable battery. The device should
shut down due to overheating (in the event the battery temperature exceeds
60°C).
FCC ID: 2AFIW-XE300C6 | 2AFIW-XE300C6
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment. -
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement.
Radiation Exposure Statement
This device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: GL- XE300C4 and GL-XE300C6 have also been tested against this SAR limit.
The Equipment named above is confirmed to comply with the requirements setout
in the European Council Directive on the Approximation of the Laws of the
Member States relating to RED (2014/53/EU). The equipment passed the test
which was performed according to the following European standards:
EN 301 489-1 V2.2.3；EN 301 489-17 V3.2.2; EN 301 489-52 V1.1.0
EN 300 328 V2.2.2; EN 301 511 V12.5.1;
EN 301 908-1 V11.1.1; EN 301 908-2 V11.1.2; EN 301 908-13 V11.1.2;
EN50566:2017& EN62209-2:2010; EN62368-1:2014+A11:2017
This product uses WiFi 2.4GHz Operating Frequency is 2400~2483.5MHz; The
Product comply with Directive 2011/65/EU and its amendment directive
2015/863/EU (Rohs2.0)