FE-D20SFV4-LP Fender Eliminator Kit Low Profile for 2020-2023 Ducati Streetfighter V4 Instructions
- June 1, 2024
- DUCATI
Table of Contents
FE-D20SFV4-LP Fender Eliminator Kit Low Profile for 2020-2023 Ducati
Streetfighter V4
Product Information
Specifications:
- Product Name: Fender Eliminator Kit Low Profile
- Compatibility: 2020-2023 Ducati Streetfighter V4/V4S
- Part Number: FE-D20SFV4-LP
- Includes: Plate Holder, Cover Plate, Wedge Bracket, License plate LED light, License light adapter harness, Bolts, Washers, Nylon lock nuts
Product Usage Instructions
Installation Steps:
- Locate the under tail area of your Ducati Streetfighter V4/V4S.
- Attach the Plate Holder using the provided bolts and washers.
- Secure the Cover Plate over the Plate Holder with the included fasteners.
- Mount the Wedge Bracket in the designated spot on the under tail area.
- Connect the License plate LED light and adapter harness to the appropriate connectors.
- Use the T20 Torx bit to tighten all bolts and nuts securely.
- Apply Loctite or thread sealer to the threads for added security.
Parts List
- x1 Plate Holder
- x1 Cover Plate
- x1 Wedge Bracket
- x1 License plate LED light
- x1 License light adapter harness
- x5 M5x12mm allen bolts
- x4 M6x16mm allen bolts
- x5 M5 washers
- x4 M6 large OD washers
- x4 M6 nylon lock nuts
Required
- T20 Torx bit
- Loctite or thread sealer
INSTALLATION INSTRUCTION
- Remove lower half of factory rear fender (4 T20 Torx bolts from underneath) and carefully lower down.
- Unplug left and right turn signals connectors as well as the license plate light connector, pop off and cut the wire harness holder cable tie to completely drop the lower half.
- Remove upper half of factory fender (2 bolts from underneath) then pull down and slide forward. Un-route the wire harness through to completely remove.
- Tuck the excess harness slack back into the undertail, leaving exposed the license plate light plugs. Note this kit does not come with brackets for mounting turn signals. An integrated tail light or other external signals required.
- Mount the Wedge Bracket to the under tail by inserting into the rearward rubber grommet and secure using two (2) M5x12mm bolts and M5 washers. Ensure the proper direction the welded nuts protrudes on the top side. Apply a drop of Loctite or thread sealer on these bolts. Ensure the license plate light plug is protruding forward of the Wedge Bracket.
- Mount the LED license plate light to the plate holder making sure the LEDs are facing downwards to the license plate. Feed the black/white wires through the Feed Hole on the Cover Plate and attach the adapter harness white> yellow and black>blue.
- Plug in the LED license plate light to the bike and mount the Plate Holder to the Cover Plate to the Wedge Bracket using three (3) M5x12mm bolt and M5 washers. Apply a drop of Loctite or thread sealer on these bolts. Make sure to align the corresponding holes on the Plate Holder to the Cover Plate/Wedge Bracket before tightening. See illustration below.
- Mount the license plate to the Plate Holder using four (4) M6x16mm bolts, M6 large OD washers and M6 lock nuts.
- Turn on the bike and verify light functionality.
FAQ
-
Q: Can this Fender Eliminator Kit be installed on other Ducati models?
A: This specific kit is designed for use with the 2020-2023 Ducati Streetfighter V4/V4S models. It may not be compatible with other Ducati models due to variations in design and dimensions. -
Q: Is any special tool required for the installation?
A: Yes, you will need a T20 Torx bit to tighten the bolts and nuts included in the kit. Additionally, using Loctite or thread sealer is recommended for added security during installation.
copyright © Motodynamic 2024 TM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>