CONNECTS2 CT23AU13 Double DIN Fitting Kit User Guide
- June 6, 2024
- Connects2
Table of Contents
CT23AU13/L
Double DIN Fitting Kit for Audi (MMI) Vehicles
IN THE KIT
i. Double DIN Fascia Panel*
ii. Brackets
iii. MMI Button Panel
iv. MMI Button Bracket
v. Hex Screws (x8)
*Note the fascia panel showcased throughout this instruction manual is for Right-hand vehicles.The procedure is identical for Left-hand vehicles, although you will need to use the CT23AU13L fascia panel during installation.
APPLICATION
Note: Application data is subject to change at any time
A4 (8K) 2008 – 2015
A5 (8TF, 8F7, 8TA) 2008 – 2015
Note: the vehicle will need modification. Please familiarise yourself with the
instructions before undertaking the installation.
RECOMMENDED TOOLS
- Panel Removal Tool
- Pick Tool
- Screwdriver
- 8mm Socket Wrench
- Cutting Tool
FEATURES
- Allows for the installation of a double-DIN aftermarket stereo
- Includes mounting brackets and fitting accessories
- Finished in matt black to match the vehicle dashboard
DISCLAIMER
The information provided in this document is subject to change without notice
due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer
of this product cannot be held responsible for any changes made to the vehicle
by the manufacturer or damages that may occur through the installation of this
product in accordance with the steps outlined herein.
Need help? Visit
support.connects2.com/tickets/technical
V2 03/21
OVERVIEW DIAGRAM
- Double DIN Fascia Panel
- Left/Right Brackets
- Button Relocation Panel
- Button Relocation Bracket
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are used during the installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product.
INSTALLATION GUIDE
Audi MMI OEM dashboard. Ensure that the appropriate area of the dashboard is protected by a suitable material to avoid damage during installation.
DASH DISASSEMBLY
Begin by using a Bojo tool (or similar variant) to pry away and unclip the
trim that surrounds the top screen.
Once loose, disconnect the hazard switch connector and place to one side.
Using the Bojo tool again, pry away and unclip the bottom HVAC panel.
Once loose, disconnect the panel connectors and place to one side.
Using a pick tool, insert it in between the fan blades and release the spring
clips.
Once free, remove and place into storage.
DASH DISASSEMBLY
Using a pair of radio release keys (e.g. CT22AU01) remove the head unit. When
free, disconnect all the wiring.
You will then need to guide the MMI button connectors down toward the gear
stick opening (see step 5-6).
Pull the gear stick cover-up and then firmly pull on the center gear panel.
Disconnect both wires and put to one side.
Remove 2x 8mm screws located toward the bottom of the ashtray panel (see image
reference).
When free, carefully lift and pull the ashtray pocket up out of the dashboard.
Using a blade or Dremel tool, proceed to cut the portion of the interior dash highlighted. This allows the new head unit to sit higher and in alignment with the fascia plate.
KIT ASSEMBLY
Take the OEM head unit in hand and gently remove the buttons by means of
releasing the surrounding plastic.
In addition, remove the two rubber grommets from the back of the OEM ashtray
(see image reference).
Install the OEM head unit buttons into the new Button Relocation Bracket. Further proceed to install this button and bracket combination into the back of the new Button Relocation Panel (see image reference).
Attach the new Double DIN Brackets to the aftermarket head unit utilizing the screws within the kit.
With the brackets attached to the head unit, offer the whole unit to the back
of the new Double DIN Fascia.
Use the plastic inserts at the bottom of both the Brackets and the Fascia as a
guide.
KIT INSTALLATION
With the new Button Relocation Panel fully assembled, install it into the
opening where the ashtray originally sat.
Before fully placing, make sure to re-connect both MMI button connectors.
Once the Button Relocation Panel is seated properly, screw the panel down into place using the OEM screws.
With the Button Relocation Panel fully connected and in place, begin to re-
introduce the gear panel back into the dashboard.
Connect the relevant OEM wiring in the process.
After connecting all the necessary wiring, begin to install the new Double DIN
Fascia with the aftermarket head unit into the dashboard.
Firmly press down around the edges to ensure it clips into place – this will
complete the installation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>