VIVO DESK-E144B Black Electric Desk Controller Instruction Manual
- June 6, 2024
- Vivo
Table of Contents
VIVO DESK-E144B Black Electric Desk Controller
SKU: DESK-E144B Controller
| Scan the QR code with your mobile
device or follow the link for helpful videos and specifications related to
this product.
---|---
https://vivo-us.com/products/desk-e144b
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
|
www.vivo-us.com
Chat live with an agent!
|
---|---|---
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED. · DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
OPERATING CONTROL PANEL
OPERATING INSTRUCTIONS: When the system is powered on, the existing desktop height will appear on the control panel.
Upward and Downward Movement
Press and hold the up or down arrow until the desk reaches the desired height.
Memory Mode
To store a certain height in the controller’s memory, first press “S”. The
controller display will begin flashing. Now press the sitting position or
standing position button within 6 seconds to store the current height in
memory. Once in memory, you can recall the sitting or standing height settings
by pressing the corresponding button. Touching any button will stop the
automatic adjustment.
Power-Saving Mode
When no actions are made for over 2 minutes, the system will enter power-
saving mode. Touch any button to enter operation mode.
Function Mode
Press and hold the “S” button for 3 seconds, or until “S – -” begins flashing
on the display. Press “S” again to enter Function mode. Within function mode,
use the up and down buttons to scroll through settings, and use the “S” button
to select options. If no action is taken for 20 seconds, the desk will return
to operating mode.
- Change Displayed Unit (Un): Press the up or down buttons until the display shows “Un”, and press “S” to select. Press up or down to select “SI” (metric) or “In” (imperial). Hold “S” for 2 seconds to save the setting.
- Change Brightness (br): Press the up or down buttons until the display shows “br”, and press “S” to select. Press up or down to select Low (L), Normal (n) or High (H) brightness. Hold “S” for 2 seconds to save the setting
- Collision Force Detection (CF): Press the up or down buttons until the display shows “CF”, and press “S” to select. Press up or down to select “OFF”, Low (L), Normal (n) or Heavy (H) collision force detection. Hold “S” for 2 seconds to save the setting.
Reset Mode
While the unit is powered on, press the down arrow until the desk moves to the
fully lowered position. Press and hold the down arrow for 5 seconds or until
“rES” is displayed to enter reset mode. Continue holding the down arrow, and
the desk will move down to the lowest possible height and then move back up
slightly. The desk will then return to operating mode.
- E20 – Desk Overload: If overloaded while moving up, error will clear after 3 seconds. If overloaded moving down, unplug desk for 10 seconds then reconnect power.
TROUBLESHOOTING
Error Code Description/Resolution
| Error Code | Description/Resolution |
|---|---|
| HOT | Heat Warning: Allow desk to rest for 18 minutes |
| E10 | Motor connection fault: Disconnect desk power, disconnect the |
motor, reconnect the motor, then reconnect power.
E20| Desk overload: Unplug desk for 10 seconds then reconnect to power
E02| Obstacle protection. Desk will automatically move back 4cm after
collision.
E31| Under-voltage (power brown out). Will clear automatically when line
power is corrected.
E32| Over-voltage (power surge). Will clear automatically when line
power is corrected.
NOTES
- Circuit Protection: If motor or controller becomes disconnected, the desk will cease operation. Error will clear after all components are reconnected.
- Self-protection function: The unit will enter a protective mode should the system operate continuously in excess of 2 minutes with “HOT” on the controller display. The system will return to normal operation after approximately 18 minutes.
- Do NOT remove or reconnect power to reset the unit when in a protective or “HOT” state, as this may damage the electronics.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
help@vivo-us.com
www.vivo-us.com (Chat live with an agent!)
309-278-5303
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESOLUTION TIME (within office hrs): 5M 4S
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo- us.com
Documents / Resources
| VIVO
DESK-E144B Black Electric Desk
Controller
[pdf] Instruction Manual
DESK-E144B, Black Electric Desk Controller
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>