BITMAIN AntMiner Asic Miner User Manual
- June 6, 2024
- BITMAIN
Table of Contents
The first glance
AntMiner S1 is a blade-style miner, which contains two blades. It has been assembled before Fab out. Bellow screen shows all AntMiner S1’s components:
One blade miner can work separately, it is shown in bellow:
Notice:
- You should prepare your own ATX Power Supply.
- To connect your Miner via WIFI, you should prepare your own WIFI antenna.
Power Supply
Connect the 12V Power line to the Power Supply socket. Note not to reverse positive (+12V) to negative (GND).
Connect to Miner
3.1 WAN setting
Step 1. Read the IP address labeled in the Fan Bracket (Front). Manually
set up your PC’s IP address in the network segment same as the miner’s IP
address.
Step 2. Connect miner and your PC via network cable.
Step 3. Enter miner’s IP address into your web browser, then login miner
management interface, both of username and password is ‘root’ by default.
Setp 4. Set LAN as DHCP client. Click “Network->Interface->LAN”, select
DHCP client like the following page, and then click “Switch Protocol“, and
then click ”Save & Apply”. The default LAN value of the first several
batches is fixed to 192.168.1.1, and the WAN address can’t be set as
192.168.1.x, otherwise, the AntMiner can’t be accessed. If your miner’s LAN
is set as DHCP by default, please ignore this step.
Step 5. Modify the IP address of the WAN interface. Click “Network->Interface->WAN” to modify the IP address of WAN on the following page.
Note:
-
WAN and LAN can’t be at the same network segment. Please set WAN to DHCP client or different network segment with WAN. The
LAN of a new version of the container will be set to DHCP by default. -
If you set fixed IP to WAN interface, please remember it, otherwise, you may not access the miner.
3.2 WIFI setting
There is WIFI built-in in the container, and it can be used to connect to the
Ethernet via another WIFI hot point. Note: Bad WIFI performance will reduce
the miner’s hash rate. You have to prepare the WIFI antenna by yourself.
Through “Network->Wifi“ you can click ”Scan“ and then add the existing WIFI
signals in your environment.
Pool Setting
Through ‘Status->Miner Configuration ‘, you will be able to configure your miner. Pool URL- you should enter the URL of your desired pool. Worker- this is your worker ID on the selected pool. Password- This is the password for your selected worker. In general, passwords can be set casually. Comment: AntMiner can set up three mine pools, the priority decreases from the first pool (pool 1) to the third pool (pool 3). The low priority pool will start to work, only when the high priority pool encounter fault.
Miner Status
Through ‘Status-> Miner Status‘, you will be able to check your miner running
status. ASIC#: ASIC number in the chain Fan: Fan speed
Temp: Temperature, centigrade Frequency: ASIC setting frequency ASIC status: o
stands for OK, x stands for error.
System Configuration
6.1 Password Modification
Through ‘System->Administration’, you will be able to modify the AntMiner
login password, and choose ‘Save’ and ‘Save and Apply’ after modifying it.
6.2 System Upgrading
Through ‘System->Backup / Flash Firmware’ you will be able to upgrade your
miner.
‘Keep setting’ is chosen by default, you should choose it if you hope to preserve the current settings. You should cancel this option if you hope to restore it to initial settings. Click the ‘Browse’ button to choose the upgrade file. After choosing the upgrade file, then click the flash image…’ button to start downloading this file to your system. After downloading, please click the ‘Proceed’ button, then upgrade the system. During the upgrade process, you need to wait patiently and must keep the power on, otherwise, AntMiner will restore to initial settings. AntMiner will be connected to the login interface after finishing the system upgrade.
AntMiner Manual
Last updated: 11/26/2013
Documents / Resources
|
BITMAIN AntMiner Asic
Miner
[pdf] User Manual
AntMiner, Asic Miner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>