SAVANT SSC-W02R SmartControl RS232 Wi-Fi Controller User Guide

: June 6, 2024
: SAVANT

Table of Contents

Box Contents
Specifications
Network Guidelines
Front Panel
Rear Panel
Connecting to a Wireless Network
RS-232 Wiring and Connections
Additional Documentation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SAVANT SSC-W02R SmartControl RS232 Wi-Fi Controller User Guide

Box Contents

SmartControl RS232 Controller (SSC-W02R)
Installation Kit (075-0174-xx)
Mounting Plate (074-0569-xx)
6-pin Screw Down Plug-in Connector (028-9352-xx)
5V DC 1.2A Power Supply (025-0207-xx)
Cable Tie (014-0071-xx)
Product and Regulatory Insert (009-1950-xx)

Specifications

Environmental

Temperature: 32° to 104° F (0° to 40°C)
Humidity: 10% to 90% (non-condensing)

Dimensions and Weights

	Height	Width	Depth	Weight
Device	0.64 in (1.62 cm)	2.70 in (6.85 cm)	2.67 in (6.78 cm)	0.50

lbs (0.22 kg)
Shipping| 3 in (7.62 cm)| 7 in (17.78 cm)| 10 in (25.40 cm)| 2.0 lbs (0.90 kg)

Power

Input: 5V DC 1.2A
Maximum: 6 watts

Standards

Wireless| Wi-Fi (802.11 b/g/n 2.4 GHz)

IMPORTANT! 802.11r (fast roaming) is not supported.

---|---
Security| WPA™, WPA2™, WPA/WPA2™, WEP

Regulatory

Safety and Emissions| FCC Part 15| CE
| C-Tick
| UKCA

---|---|---|---|---
Contains FCC ID:| TLZ-CU277| | |
Contains IC:| 6100A-CU277
RoHS| Compliant`
Minimum Supported Release
Savant OS| da Vinci 8.2

Network Guidelines

For more information, see the Savant Device Networking Guidelines on the Savant Customer Community.

Front Panel

Product Overview

A: Press and hold for five seconds while powered On to clear the network settings. The Status LED blinks rapidly when reset is complete.

Off: No Power

On Solid: Provisioned to the local network and communicating with the Savant System Host.

Blinks Once: In Provisioning Mode. Ready to be added to the local network
Connection

Blinks Twice: Establishing connection with the local network.

B :

Blinks Three Times: Connected to the local network. Is connecting to the Host.

Short Off Blink: Firmware is updating.

Rapid Blink: The reset button was held down for at least five seconds and the SSC-W02R is performing a factory reset. After reset, all network settings are cleared and the factory defaults are set.

Rear Panel

Product Overview

RS-232 Port 1 – 6-Pin Plug-In Connector (Left 3 Pins)

Connecting to a Wireless Network

Refer to the SmartControl RS232 – Wi-Fi Smart Controller with 2 RS232 Deployment Guide located on the Savant Customer Community to connect the SSC-W02R to the local network.

RS-232 Wiring and Connections

A 6-pin screw down type connector is included with each SSC-W02R controller. This connector plugs into the connection on the rear of the controller.

Wiring and Connections

Remove power if applied.
Pull to remove the terminal block from the rear of the controller.
With a small flat bladed screwdriver, turn the screws on top of the connector counterclockwise until the silver crimps in the rear of the connector open enough to slide the wire(s) into the square slots.
Strip back the insulation on each of the wires ¼ inch. Insert the stripped wires into their proper ports. Do not allow more than 1/8 inch of bare wire exposed.
Turn the screws on the top of the connector clockwise until the crimps tighten around each wire. Tug on each wire a bit to verify they are installed securely.
Plug terminal block back into the rear of the controller.
Reapply power.