american lighting N7847-711 Brookcrest 8 Light Sand Coal and Gold Leaf Cage Pendant Light Instruction Manual

american lighting N7847-711 Brookcrest 8 Light Sand Coal and Gold Leaf

Cage Pendant Light

Product Information

The product is a light fixture with item number N7847-711. It comes with a mounting strap, all-thread rods, support cable, canopy, candle cover, and fixture screws. The fixture can accommodate up to eight candelabra base bulbs with a maximum wattage rating of 60 watts each or CFL or LED equivalent. The product also includes a wire restraint to adjust the length of the cable.

Product Usage Instructions

1. Unpack the fixture and lay out all the parts on a clear area, making sure not to lose any parts necessary for installation.

2. Shut off the power at the fuse box or circuit breaker and remove the old fixture, including the mounting hardware if necessary.

3. Determine the desired hanging height and thread rods (B & C) into the top all thread of fixture body. Press wire restraint to adjust length of cable (D).

4. Pass the fixture wires through each rod as you assemble. Pass the wires through canopy (E) and pull until tight. Then thread the canopy onto top of rods.

5. Attach the mounting strap to the outlet box using box screws
   (Size: #8-32*0.5L), making sure that the side of the mounting strap marked GND faces out.

6. Align the fixture to the mounting strap and attach hook on the end of support cable into a slot located on mounting strap. Carefully allow support cable to support the weight of the fixture while wiring.

7. Connect the electrical wires as shown in Fig. 3, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting strap using the green screw provided.

8. Tuck wire connectors neatly into outlet box.

9. Place fixture canopy (E) over two fixture screws (or all thread) and secure with decorative nuts.

10. Place candle cover (A) on socket.

11. Install eight candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
    DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

12. Turn on the power and test the fixture.

Note: Do not clean your light fixture or parts with water or cleanser.

INSTALLATION INSTRUCTIONS

Item #N7847-711 (07/18/2022)
READ AND SAVE THESE INSTRUCTIONS

WARNING: SHUT POWER OF F AT FUSE OR CIRCUIT BRE AKER.AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING THE FIXTURE (Fig.2)

1. Carefully unpack the new fixture and lay out all the parts on a clear area. Take care not to lose any parts necessary for installation.
2. Shut off the power at the fuse box or circuit breaker. If necessary, remove the old fixture, including the mounting hardware.
3. By measuring, determine desired hanging height and thread rods (B & C) into the top all thread of fixture body. Press wire restraint to adjust length of cable (D).
4. Carefully pass the fixture wires through each rod as you assemble.
5. Pass the wires through canopy (E) and pull until tight. Then thread the canopy onto top of rods.

MOUNTING THE FIXTURE **

**

1. The mounting strap contains several pairs of threaded holes, find the pair of holes that match holes spacing in your fixture canopy and thread two fixture screws into mounting strap and tighten with hex nut. Note: The length of fixture screw into mounting strap may be adjusted if necessary.
2. Attach mounting strap to the outlet box (not included) using box screws (Size: #8-32*0.5L). The side of mounting strap marked “GND” must face out.
3. The support cable is provided to support the weight of fixture while wiring. Align fixture to mounting strap and attach hook on the end of support cable into a slot located on mounting strap. Carefully allow support cable to support the weight of the fixture while wiring.

CONNECTING THE WIRES

1. At this point, connect the electrical wires as shown in Fig. 3, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting strap using the green screw provided.
2. Tuck wire connectors neatly into outlet box.

FINISHING THE INSTALLATION

1. Place fixture canopy (E) over two fixture screws (or all thread) and secure with decorative nuts.
2. Place candle cover (A) on socket.
3. Install (8) eight candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the outlet box and test the fixture.
Note: Illustration on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Do not clean your light fixture or parts with water or cleanser.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>