AUKEY EP-N6L Wireless Earbuds User Manual

AUKEY EP-N6L Wireless Earbuds

Package Contents

• True Wireless Earbuds
• Charging Case
• USB-A to C Cable
• Three Pairs of Ear-Tips (S/M/L)
• User Manual
• Quick Start Guide
• Warranty Card

Product Diagram

1. Noise Reduction
2. Microphone Pickup
3. Touch-Sensitive
4. Panel (Pinching)
5. Charging Contacts
6. Microphone
7. Charging Case LED Indicator
8. Earbuds LED
9. Indicator

Specifications

Earbuds

Charging Case

Getting Started

Charging

1. Fully charge earbud case before initial use. To charge, connect the case to a USB charger or a charging port with the included USB-A to C cable
2. The LED indicator will turn red whilst the case is charging. The case is fully charged when the indicator turns green
3. Charging takes around 2 hours. After being fully charged, it can recharge the earbuds up to 4 times
4. The earbuds should be stored in the case when not in use

Note: Remove the protective film from the earbuds before first-time usage

Turning On / Off

Turn On

| Open the lid of the charging case, or press and hold the touch-sensitive panels on both earbuds for 2 seconds whilst

they are turned off

---|---

Turn Off

| Return both earbuds to the charging case or touch and

hold on the touch-sensitive panels on both earbuds for 10 seconds when they are turned on

Pairing Earbuds

Begin with the earbuds in their case:

1. Open the charging case. They will turn on automatically and connect within  5 seconds
2. Turn on the pairing function on the device you want to pair with the earbuds From the list of available devices, find and select “AUKEY EP-N6”
3. If a code or PIN is required for pairing, enter “0000”

Use After Pairing

Once the earbuds have been successfully paired to your device, they can be switched on and off as follows:

1. Open the charging case – they will turn on and sync automatically
2. To power off – put the earbuds back into the charging case and close the lid, they will begin charging

Using the Left/Right Earbud Only

Starting with the earbuds in the case:

1. Take the left/right earbuds out
2. Turn on the pairing function on the device to pair with the earbuds
3. From the list of available devices, select “AUKEY EP-N6”

Notes

• Earbuds will automatically reconnect to the last-paired device once they have been switched on
• In pairing mode, the earbuds will automatically turn off after 5 minutes if no device is synced
• To clear the pairing list, take the earbuds out of the charging case and press both earbuds for 10 seconds to turn them off, then press the touch-sensitive panels on both earbuds for 10 seconds.
• If one of the earbuds has no sound, return earbuds to the charging case, leave them for a moment – then take them out again and reconnect
• The range on these wireless earbuds is 15m (50ft). If you exceed this range, the earbuds will disconnect from your paired device. The connection will be re-established if you re-enter the wireless range within 10 minutes. The earbuds will automatically reconnect to the last paired device. To connect with other devices, follow the previous pairing steps

Controls & LED Indicators

Streaming Audio Once paired, you can wirelessly stream audio from your device to the earbuds. Music will automatically pause when you receive an incoming phone call and resume once the call has ended.

earbud

Taking Calls

Answer or end a call| Double-tap the touch-sensitive panel on either earbud to answer or end a call
---|---
Reject an

incoming call

| Touch and hold the touch-sensitive panel on either earbud for 2 seconds
Use Siri or other voice assistants| While your device is connected, quadruple- tap the touch-sensitive panel on either| LED Status Indicator (Earbuds)| Status
---|---
Green| Earbuds are fully charged
Red| Earbuds are charging

earbud

Product Care & Use

• Keep away from liquids and sources of extreme heat
• Don’t use the earbuds at high volume for extended periods– this may cause permanent hearing damage or loss

Warranty & Customer Support

For questions, support, or warranty claims, contact us at the address below that corresponds with your region. Please include your Amazon order number and product model number.

• Amazon US orders: support.us@aukey.com
• Amazon EU orders: support.eu@aukey.com
• Amazon CA orders: support.ca@aukey.com

*Please note, AUKEY can only provide after-sales service for products purchased directly from AUKEY. If you have purchased from a different seller, please contact them directly for service or warranty issues.

CE Statement

• Max RF power level: BT classic (2402–2480MHz): 2.1dBm RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission above the reference level as specified in EC Council Recommendation (1999/519/EC).
• CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
• NOTE: Excessive sound pressure from earphones and headphones can cause hearing loss if used for extended periods.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>