Aukey PB-MS01 Power Bank User Manual

USER MANUAL
MagLink 6.7K

PB-MS01 Power Bank

Charging Your Phone or Tablet Using Charging Cables Charging Your Phone Wirelessly Ready to wireless charge
Chargin Foreign object detected
Charging Your Smart Watch or Bluetooth Earphones

1. Enter low-current charging mode: Press and hold the power button for 3 seconds, and three white LED lights turn on and off alternatively every 6 seconds.
2. Charge your smart watch, Bluetooth earphones, or other low-power accessories.
3. Exit low current charging mode: Press and hold the power button for 3 seconds.

Charging Devices Wirelessly and Using Cables Simultaneously Recharging Your MagLink 6.7K Notes

• The USB-C port supports USB Power Delivery fast charging for iPhone 8 and later when used with a certified Apple USB-C to Lightning cable.
• This product can provide perfect magnetic alignment for iPhone 12 / 13 / 14 / 15.

Product care and precautions

• Do not impact or drop the product.

• Keep away from liquids and extreme heat.

• Recharge the power bank at least once every 3 months.

• Do not leave the product in the car for a long time.

• Do not leave the product in the car for a long time.

• Do not disassemble or modify.

• Please stop using the product immediately and contact the support center in the following cases.
  – The product has an abnormal smell such as burnt smell

• Batteries should be disposed of according to local environmental law.

** This product complies with the radio interference requirementsof the European Community.
Declaration of Conformity
This product is intended for use within Europe. This equipment compiles with the essential requirements for the Radio Equipment Directive 2014/53/EU. AUKEY Technology Co., Ltd. hereby declares that this product PB-MS01 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU, 2014/30/EU. The Declaration of Conformity for the PB-MS01 is available from www.aukey.com
** This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Warranty & Customer Support
For questions, support, or warranty claims, please contact your seller directly.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure statement.

The device can be used in portable exposure condition without restriction.

Specifications

Wireless: 15W (Max) / 10W / 7.5W / 5W
Total output| 20W
---|---
Operating temperature| 0-40 C
Storage temperature| -10-45C
Dimensions| 109 x 68 x 17mm / 4.29″ x 2.68″ x 0.67″
Weight| 172g / 6.07oz

Follow Us to Unlock More about AUKEY:
@AUKEYofficial
@aukeyofficial
@AUKEYofficial
AUKEYofficial
Model: PB-MS01
Aukey Technology Co., Ltd.
www.aukey.com | support@aukey.com
Room 116, Kangli Information Valley Building, Shanglilang Community,
Longgang District, Shenzhen, Guangdong, 518111, China
FCC ID：2ATIH-PB-MS01
Made in china

References

• AUKEY Official | Unlock More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>