Smoove® 1 & 4 RTS

The Smoove 1 RTS controls a single group of window coverings.
The Smoove 4 RTS controls up to four different groups of window coverings.

Part Numbers:
Smoove 1

1811533

Smoove 4

1811748

Introduction

Installation

A. Mounting frame
B. Smoove frame
C. Smoove 1 or 4 (4 is shown)

Install on a clean, flat interior wall within 35 feet of window coverings.

1. Install the mounting frame using provided, countersunk screws in the corners of the plate to the wall.
2. Snap the frame onto the mounting plate (notch facing downward).
3. Clip the Smoove RTS module onto the assembly.
4. The product can be mounted to the wall using double-sided tape (3M tape)

Note: Locating the module near a metal frame or surface may impede the product’s operation.

Operation for Smoove 1

Pairing a Smoove 1 to a window covering

• Press and hold the Programming (PROG) button on the window covering motor until the window covering moves up and down. Note: You have 2 minutes to successfully complete RTS programming or it will default back to the factory setting, and you will have to start the process over again.
• Press the Programming (PROG) button (E) on the back of the Smoove 1 until the window covering begins to move up and down.
• The Smoove 1 is now paired with the window covering the motor.

Daily Use

• On the Smoove 1, press the (A) or (C) to open or close the window covering.
• To stop the window covering at a specific position, press the “my” button (B).

Creating Preset Positions

To create a preset position:

• Adjust the window covering to the desired position.
• Press “my” on the Smoove 1 until the window covering moves up and down. The preset is now activated.

To delete a preset position

• Press the “my” button. The window covering moves to a preset position.
• Press the “my” button again until the window covering moves up and down. The preset position has been deleted.

Daily use of preset positions

• Briefly presses the “my” button. The window covering will move to the preset position.

Operation for Smoove 4

The Smoove 4 operates four different groups of window coverings.
As you pair your Smoove 4 to each window covering controller, you also build each grouping.

Pairing a Smoove 4 to a window covering and creating channels

• Press and hold the Programming (PROG) button on the window covering motor until the window covering moves up and down. Note: You have 2 minutes to successfully complete RTS programming or it will default back to the factory setting, and you will have to start the process over again.
• Assign the window covering to a channel by selecting that channel (D) on the Smoove 4.
• Press the Programming (PROG) button (E) on the Smoove 4.
• The window covering will move up and down, indicating a successful pairing.
• Repeat this procedure, assigning window coverings to channels until you have paired all the window coverings to the Smoove 4.
• To remove a window covering from Smoove 4 control or to change its channel:
  1. Press Programming (PROG) on the mounted window covering the motor.
  2. Press the channel button (D) on the Smoove 4 to which the window covering is assigned.
  3. Press the Programming (PROG) button (E). The window covering will move up and down, indicating it is now removed from the Smoove 4 and its assigned channel.

Daily Use

• On the Smoove 1, select a channel, then press the (A) or (C) to open or close the window covering.
• To stop the window covering at a specific position, press the “my” button (B).

Creating Preset Positions
To create a preset position:

• Press the channel number (E).
• Adjust the window coverings to the desired position.
• Press the “my” button (B) until the window coverings move up and down. The preset is now activated.

To delete a preset position

• Press the channel number (E).
• Press the “my” button (B). The window coverings move to a preset position.
• Press the “my” button (B) again until the window coverings move up and down.
  The preset position has been deleted.

Daily Use of Preset Positions – The “my” button on the Smoove 4 opens and closes your window coverings to your preferred preset conditions.

• Press the channel button (E
• Press the “my” button (B).
• The window covering will move to a preset position.

Battery Replacement

1. Unclip the frame by using a small flat head screwdriver to open (against the small groove is shown in image 1)
2. Remove old battery then insert a new CR 2430 3 V battery, (+) side up.
3. Replace the frame and Module onto the mounting frame by pressing back to the original position.

Troubleshooting

Replacing a lost or broken Smoove 1 or 4 Controller

To Replace a lost or broken remote, follow these steps with the NEW transmitter.

1. Press and hold the Programming (PROG) button on the window covering motor until the window covering moves up and down.
2. Press the Programming (PROG) button (E) on the back of the Smoove 1 until the window covering begins to move up and down.
3. The Smoove 1 is now paired with the window covering the motor.
4. Follow steps of the installed motor to set the upper and lower limits

Note: Visit https://store.somfysystems.com/ to purchase an additional or replacement product.

AS WITH ANY PRODUCT INVOLVING THE GENERATION OF ELECTRICAL POWER, CAUTION MUST BE USED AT ALL TIMES. PLEASE CAREFULLY READ AND FOLLOW ALL OF THE INSTRUCTIONS.

This device is FCC certified and complies with part 15 of the FCC rules.
RTS compatibility: RTS transmitters are capable of operating any RTS motor.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>