h fats Spin 900 Mood Lantern Mood Lantern Instruction Manual

: June 29, 2024
: h fats

h fats Spin 900 Mood Lantern Mood Lantern

INTENDED USE

This product (hereinafter referred to as “SPIN”) is intended as a decorative table-top fire to be used in a well-ventilated room or outdoors and for private use only.

The torch version/conversion of the SPIN is only suitable for outdoor use.

Any use or modification of the product other than that described in these instructions is considered improper and may result in damage to property or even personal injury.

The manufacturer accepts no liability for damage caused by improper use.

WARNING SYMBOLS ON THE PRODUCT AND IN THE OPERATING INSTRUCTIONS

The following symbols and signal words are used in these operating instructions, on the product or on the packaging.

WARNING!

This symbol/signal word warns you of a hazard that can result in death or serious injury.

CAUTION!

This symbol/signal word warns you of a hazard that may result in minor or moderate injury.

NOTICE

Symbol This symbol/signal word draws your attention to possible damage to property.
Symbol This symbol gives you useful additional information on assembly or operation.

Symbol This symbol refers to further information on the supplied assembly & installation sheet.

WARNING!

Fire hazard!
This symbol warns you of hazard from open fire, which can ignite things in the vicinity and seriously injure or kill people by fire.

CAUTION!

Danger of burns from hot surfaces!
This symbol warns you of a hazard from hot parts/surfaces that may result in minor or moderate burn injury.

WARNING!

Explosion hazard due to highly flammable or explosive substances!
This symbol warns you of a danger from highly flammable or explosive substances that can result in death or serious injury.

WARNING!

Risk of fire and injury when handling liquid fuel!

Liquid fuel can ignite when poured into the still hot or burning Bio-Burner!
Symbol Never fill liquid fuel into the Bio-Burner while it is hot!
Symbol Never fill liquid fuel into the Bio-Burner while it is burning!
Symbol Be sure to also read the information on the safety data sheet for the liquid fuel tank!

WARNING!

Danger to life from installation and use indoors!
This symbol indicates that indoor use is prohibited!

SAFETY INSTRUCTIONS

Symbol Read the following instructions carefully and completely before using the SPIN!

Keep the instructions for further use. If you pass the SPIN on to third parties, be sure to include these operating instructions.

The instructions are based on the standards and rules applicable in the European Union. Observe regionally applicable restrictions and laws.
Keep children and pets away from the SPIN. Take special care when lighting, during operation and when cooling down.

WARNING!

Danger to life due to gas development and carbon monoxide poisoning!
Liquid fuel does not burn completely residue-free. The surrounding air also becomes more humid and is used up more quickly.

Operating the SPIN in poorly ventilated areas can result in poisoning or death from carbon monoxide poisoning!

Only use the SPIN in well-ventilated areas.
Apart from the SPIN, there must be no other fire in the same room!
Do not operate the SPIN in closed and very small spaces, e.g. B. tents, caravans, mobile homes, boats.
When used indoors, observe the specifications for room size, operating time and ventilation under “Notes on room size”!

WARNING!

Explosion hazard due to highly flammable or explosive substances!
Operating the SPIN near flammable or explosive materials can result in injury or death from flash fires or explosions!

Improper storage and handling of liquid fuel can lead to an explosion.

Never use the SPIN near deposits of highly flammable or even explosive substances such as gasoline, solvents, gases or fireworks.

WARNING!

Risk of fire due to improper use!
Improper handling of the SPIN can lead to a fire!

Never leave the SPIN unattended while in use.
Only use the SPIN at a distance of at least 60 cm from combustible and heat-sensitive materials such as paper, straw, wood, textiles, coal, car tires, electrical appliances (See Figures F, I, M).
Do not use the SPIN in strong winds or draughts.
Loose-fitting or flowing clothing can catch fire! Operate the SPIN only with well-fitting clothing.
Do not use the SPIN continuously or to heat rooms.

WARNING!

Fire hazard if objects are attached!
Items attached or hung on SPIN may catch fire during operation and cause a fire. Do not hang any other objects on SPIN and do not use any attachments other than the supplied or original höfats accessories.

WARNING!

Risk of fire and injury when handling combustibles!

This product uses bioethanol liquid fuel!
Bioethanol is a toxic and flammable liquid or gas and can cause irritation and health hazards.

Ignition can occur when SPIN is ignited, by other sources of ignition, or by exposure to sufficient heat

Keep liquid fuel away from heat, sparks and open flames when not in use.
Liquid fuel may only be used outdoors and indoors only with adequate ventilation.
Avoid spilling liquid fuel by handling carefully. Thoroughly clean up and dispose of spilled liquid fuel.
Keep liquid fuel in the original bottles only.
Never extinguish liquid fuel fires with water! Have a Class B fire extinguisher or fire blanket on hand in case of an accident.
Always store liquid fuel tightly closed in rooms where there are no open flames. Bioethanol is a fuel that evaporates when left open. At temperatures above 21 degrees Celsius, it forms a highly flammable, even explosive mixture with air.
Do not store more than 6 litres of highly flammable liquids in your home. Observe national and regional regulations, ordinances, laws and other legally binding requirements of your place of residence for the storage and handling of highly flammable liquids. The requirements may vary depending on where you live.
Always follow the instructions on the fuel container.
Check the SPIN for leaks or spills of liquid fuel before each use.
Never fill liquid fuel directly into the SPIN’s body; otherwise liquid fuel may leak out of the housing and cause an uncontrolled fire.
Avoid tipping hazards by following the SPIN’s setup instructions.
Do not leave unused liquid fuel out in the open or store it in the Bio-Burner.

WARNING!

Risk of fire and injury through the use of non-approved fuels or the use of damaged Y- Burners!
The use of non-approved fuels or damaged Bio-Burners can lead to unpredictable combustion behaviour and fires.

Only use liquid fuels from höfats with the SPIN, as specified in the technical data.
Do not use other flammable liquids such as spirit or petroleum.
Only use Bio-Burners from höfats.
If you notice damage such as rust or deformation on the Bio-Burner, stop using it and dispose of it immediately.

WARNING!

Danger of poisoning for children!
Children can drink or swallow the liquid fuel. Due to the lack of colour, there is a risk of confusion with water.

Keep liquid fuel out of the reach of children!
Be sure to also read the instructions on the fuel container!

CAUTION!

Danger of burns from hot surfaces!
During operation, parts of the SPIN become very hot and can cause burns!

Never transport the SPIN during operation or when the glass cylinder is still hot. Wait for the SPIN to cool down before transporting.
Allow the SPIN to cool completely before disassembling, converting or storing.
Wear grill gloves when handling the hot SPIN to avoid burns.

Danger of stumbling when setting up
The SPIN can present a tripping hazard when placed in areas where people are standing or walking. Personal injury or damage to the SPIN may result.

Only place the SPIN in areas where it is easily visible and out of the way of people. Particular care should be taken when setting up in the dark.
Do not place the SPIN in doorways, corridors, or other pathways where people walk.

NOTES ON ROOM SIZE

Permitted room sizes when operating 1 SPIN 900:

Room area (ceiling height approx. 2.30 m)| Windows/ doors closed| Window tilted| Window open
---|---|---|---
15 m²| ✔| ✔| ✔
10 m²| ✖| ✔| ✔
4 m²| ✖| ✖| ✔

Permitted room sizes when operating 1 SPIN 1200:

Room area (ceiling height approx. 2.30 m)| Windows/ doors closed| Window tilted| Window open
---|---|---|---
19 m²| ✔| ✔| ✔
13 m²| ✖| ✔| ✔
6 m²| ✖| ✖| ✔

PUTTING THE SPIN INTO OPERATION

Unpack and check the scope of delivery

Remove all packaging material from the SPIN.
After unpacking, as before each use, check whether the SPIN components show signs of damage. If this is the case, do not use the SPIN, and notify your retailer or contact höfats directly.
Assemble your SPIN as shown in the quick start guide and described in the following chapters.

WARNING!

Danger of suffocation from packaging film and plastic parts!
Do not let children play with packaging materials! There is a risk of suffocation!

Assembling the SPIN

Symbol You can find an illustration of the assembly and the scope of delivery in the SPIN quick guide.

Choosing the set-up location

WARNING!

For all set-up variants, observe the safety distances to combustible materials (see Figures F, I, M).

With all set-up variants, make sure that it is an appropriate location, so you do not have to move the SPIN after lighting it.

WARNING!

When used indoors, observe the specifications for room size, operating time and ventilation under “Notes on room size”!

SET UP THE SPIN AS A TABLE-TOP FIRE (FIGURES E, F, G)

Set Up The Spin As A Table-top Fire

Legend:

Extinguishing cover
Glass cylinder
Body
Stand
Eco-Ring
Bio-Burner

Screw the body onto the stand.
Place the SPIN on a flat and stable surface.
Insert the Bio-Burner into the body.
Place the glass cylinder on the body.
Follow the instructions under “Lighting the fire”!

SETTING UP THE SPIN AS A TORCH (FIGURES H, I, J, K)

Setting Up The Spin As A Torch

Either you have already purchased the SPIN as a SPIN torch or you can convert your SPIN to a SPIN torch with the ground spike.

Legend:

Extinguishing cover
Glass cylinder
Body
Eco-Ring
Bio-Burner
Rod 17 cm
. Rod 34 cm
Rod 48 cm
Nail

Use the SPIN body for the conversion without the base and without an additional riser.

WARNING!

Symbol The SPIN may not be used indoors when set up as a torch!

Depending on the desired height, assemble the parts of the ground stake as indicated on the assembly sheet (Figure J1).
Screw the nail to the ground spike.

NOTICE

Symbol By combining the different rod lengths of 48 cm, 34 cm and 17 cm, the following total lengths can be achieved:
99 cm, 82 cm, 65 cm, 48 cm, 34 cm, 17 cm.

Screw the body into the ground stake threads (Figure J2).
Insert the spike into the ground with the nail pointing downwards until the spike is completely in the ground (approx. 25 cm).
Make sure the ground spike has a secure footing.
Insert the Bio-Burner into the body (Figure J3).
Place the glass cylinder on the body (Figure K).
Follow the instructions under “Lighting the fire”!

NOTICE

Symbol Depending on the soil conditions, the insertion depth of the nail can vary. If the soil is very soft and loose, it is possible that the ground spike cannot be set up securely. If safe placement cannot be ensured, the SPIN torch must not be used.

WARNING!

If the ground spike is left in the ground without the SPIN, serious accidents can occur due to tripping. There is a risk of puncture injuries and bruises.
Do not leave the ground spike in the ground without the SPIN!

Use additional stand

Alternatively, the SPIN can also be set up in combination with a ground spike and the separately available stand (Ø 230 mm). When using the stand, make sure that it is placed on a firm and level surface, such as a table a patio floor or pavement.

CAUTION!

The base of the the SPIN 900 table-top fire (Ø 190 mm) is not suitable for use with the ground spike/torch.

HANGING THE SPIN AS A HANGING FIRE (FIGURE L, M, N, O)

Hanging The Spin As A Hanging Fire

Either you have already purchased the SPIN as a SPIN hanging fire or you can convert your SPIN to a SPIN hanging fire with the hanger.

Legend:

Extinguishing cover
Glass cylinder
Body
Stainless steel cable with hook and clamp element
Hanger
Mounting material (eye bolt 6X45, expansion dowel)
Allen key for clamping element
Eco-Ring
Bio-Burner

Use the the SPIN body for the conversion without the base and without additional riser.

NOTICE

Symbol The SPIN should be hung in a cantilevered manner from a ceiling or truss. It may only be installed on solid concrete ceilings or solid wood, as this is the only way to ensure that the eye bolt is sufficiently strong.

Installing on concrete

For secure attachment to concrete, a pre-drilled hole with Ø 10 x 60 mm must be made at the intended location.
For secure attachment, use the eye bolt with dowel included in the scope of delivery.
The screw must withstand a tensile force of at least 60 kg. Consult an appropriate specialist for the installation.

Installing on wood

For secure attachment on solid wood, a pre-drilled hole with Ø 4 x 60 mm must be made at the intended location.
Use the eye bolt included in the scope of delivery for secure attachment.

How to install the SPIN as a hanging fire

Screw the body into the thread of the hanger (Figure N1).
Connect the hook on the loop of the stainless steel cable to the hanger.
Adjust your SPIN hanging fire to the desired height with the help of the infinitely adjustable stainless steel cable (Figure O). To do this, open the Allen screw on the clamping element.
When tightening the screw again, ensure that there is sufficient clamping force. The easiest way to check this is by pulling the lower end of the frame.
Make sure that the stainless steel cable is not kinked; otherwise permanent deformation may occur.
Insert the Bio-Burner into the body (Figure N2).
Place the glass cylinder on the body (Figure N3).
Follow the instructions under “Lighting the fire”.

NOTICE

Symbol Adjusting the height of the SPIN hanging fire and hanging it must always be done without the glass cylinder.

Only hang the SPIN hanging fire in places sheltered from the wind to prevent uncontrolled swinging of the SPIN.
If the SPIN hanging fire begins to swing, it must be brought back to its resting position as quickly as possible. Always use heat resistant gloves to avoid burns.

SETTING UP THE SPIN WITH THE RISER (FIGURE P)

Setting Up The Spin With The Riser

You can use SPIN with a riser. The SPIN can be elevated from the ground using the riser.

Screw the riser between the base and the body of the SPIN.
Insert the Bio-Burner into the body.
Place the glass cylinder on the body.
Follow the instructions under “Lighting the fire”.

WARNING!

Symbol The SPIN must not be used indoors when set up using the SPIN riser! Never use more than one riser with the SPIN!

FILL BIO-BURNER (FIGURE A)

Fill Bio-burner

NOTICE

Symbol The use of fuels other than those recommended in the technical data can lead to unwanted soot formation and less flame formation or excessively high flames. In addition, the Bio-Burner can be destroyed.

Only fill the Bio-Burner with liquid fuels from höfats. This is the only way to ensure that it operates properly.

Before filling with liquid fuel, check the Bio-Burner for dirt or damage.
Insert the Bio-Burner into the body of the SPIN (Figure A1).
Fill the Bio-Burner with the liquid fuel suitable for your Bio-Burner up to the “max” mark (Figure A2).

LIGHTING THE FIRE (FIGURE B)

Lighting The Fire

Optional: Use Bio-Burner with Eco-Ring (Figure B1)

If you put the Eco-Ring on the Bio-Burner after filling, the flame is reduced a little and you save liquid fuel! This also means your SPIN will burn for longer.
CAUTION! – Risk of burns from hot surfaces! Only touch the Eco-Ring when it has cooled down and not directly after a burning process.
Light the Bio-Burner at the mesh with a stick lighter (Figure B2).

CAUTION!

Risk of burns from using unsuitable fire-starters!
Improper use of fire-starters poses a risk of burns.
Use a stick lighter to light.

CAUTION!

Risk of burns!
The flame may be difficult to see after lighting. You may burn yourself or come into contact with burning liquid fuel while attempting to check for a flame.

After lighting, always put the glass cylinder on the SPIN first.
Do not look into the glass cylinder from above!
Wear grill gloves when handling the SPIN after lighting it.

WARNING!

Risk of fire from improper ignition of the Bio-Burner!
If you light the Bio-Burner without first inserting it into the SPIN, you can burn yourself on the hot can when inserting it into the wing body. In addition, burning liquid fuel may leak and cause a fire.

Only light the Bio-Burner after you have inserted it into the body

EXTINGUISHING THE FIRE (FIGURE D)

Extinguishing The Fire

Extinguishing the Bio-Burner

To extinguish the Bio-Burner, grasp the extinguishing cover by the wire (Figure D1).
Then lower the cover into the glass cylinder until it rests on the Bio-Burner (Figure D2).
Wait for the flame to go out and the SPIN to cool before lighting or moving the SPIN again.

CAUTION!

Never use extinguishing covers from other höfats products to extinguish the Bio-Burner! Do not use any other covers than the extinguishing cover to extinguish the SPIN! Do not leave the SPIN unattended after extinguishing without checking to ensure it the flame is really out.

After extinguishing

After you have extinguished the Bio-Burner and all parts have cooled down, you can do the following:

Refill the Bio-Burner with fuel and ignite.
Insert a new Bio-Burner into the SPIN, fill it up and ignite.
Empty and discard any remaining fuel in the Bio-Burner. Observe the local/national regulations for the disposal of liquid fuel

WARNING!

Danger of fire and deflagration due to fuel residues in the Bio-Burner.
Fuel residues in the Bio-Burner will also evaporate after extinguishing and can form a flammable mixture with air in the glass cylinder of the SPIN
Do not leave any residual fuel in the BioBurner when you are no longer using the SPIN.
If possible, use up all the fuel in the BioBurner in one burn.

CLEANING AND MAINTENANCE

To protect the surfaces and avoid contamination of the flame, you should clean SPIN regularly and before each use.

WARNING!

Allow the SPIN to cool completely before cleaning.

Cleaning the Bio-Burner

Clean the Bio-Burner holder regularly with a damp cloth.

Cleaning the glass cylinder

The glass cylinder is made of high-quality borosilicate glass and is easy to clean with a soft cloth and soap.
After cleaning, rinse the glass cylinder thoroughly to remove all soap residue. Soap residue increases the risk of soot deposits on the glass and can burn into the glass.

Cleaning the body and base

Do not use any strong or abrasive solvents or scouring pads to clean the body and the base or any other parts, as these can corrode the surfaces and leave marks.

STORAGE

Do not expose the SPIN to the elements for long periods of time.
When not in use, store the SPIN in a dry, well-ventilated place away from dust.

CAUTION!

After a long period of storage, first remove dirt deposits and dust before using the SPIN again
Symbol We recommend using the cover hood, which is available as an accessory.

CAUTION!

Make sure all liquid fuel is burned before storing the SPIN!

Storage of liquid fuel

When storing liquid fuel, observe the following guidelines:

Do not store leftover liquid fuel in the Bio-Burner.
Do not store liquid fuel in combination with other flammable liquids totalling more than 20L.
Store liquid fuel only in the undamaged original bottle.
Keep the liquid fuel bottle tightly closed at all times.
Do not store liquid fuel near sources of ignition or heat.
Store liquid fuel only in well-ventilated and cool areas.

DISPOSAL

Disposing of packaging

All materials used are environmentally friendly and recycla ble. Dispose of the packaging in an environmentally friendly manner. You can find out about current disposal methods from your dealer or your local disposal facility.

Disposing of the SPIN

When the SPIN is no longer used, it can be disposed of as scrap metal.
Dispose of the glass cylinder separately at a waste glass collection point.

Ask your city or municipal administration about the options for environmentally friendly and proper disposal.

TROUBLESHOOTING & FAQ

The Bio-Burner cannot be ignited

You used a different liquid fuel in the Bio-Burner than that recommended by höfats.
- There are special ethanols that can only be ignited in certain products. These are not suitable for use in the SPIN. Empty the Bio-Burner and refill it with höfats liquid fuel. You can then ignite the SPIN again.
The wadding has become soaked with water.
- Remove the Bio-Burner from the SPIN. Then remove the remaining liquid and leave the Bio-Burner open to dry for at least 4 days. Then you can refill the Bio-Burner with liquid fuel.
- Once ignited, the SPIN will take a little longer than usual to develop a full flame. This should improve with the next burn runs.

Flame formation has changed

You used a different liquid fuel in the Bio-Burner than that recommended by höfats.
- Therefore only use the liquid fuel from höfats in your SPIN.
You are operating your SPIN when the wind is too strong.
- The SPIN is not intended for use in strong winds. We strongly advise against using it in wind or strong gusts.

The flame does not have a twisted shape.

You used a different liquid fuel in the Bio-Burner than that recommended by höfats.
- Therefore only use the liquid fuel from höfats in your SPIN.
Dirt on the Bio-Burner can affect the shape of the flame.
- Remove dirt from the cover of the Bio-Burner with a brush.

Can I use the extinguishing cover from the traditional SPIN gel burner?

No. The SPIN will not be completely extinguished when using the extinguishing cover from the gel burner.
- Only use the supplied extinguishing cover with stainless steel wire for extinguishing the Bio-Burner

Where can I dispose of leftover liquid fuel?

Check local/national regulations for disposal of liquid fuel. We recommend burning the liquid fuel completely in the SPIN.

My SPIN is dirty. What can I do?

White or black soot residues on the glass cylinder should be removed as soon as possible with a microfibre cloth and clear water. It is best not to use cleaning agents. If you use cleaning agents, make sure that no residue is left on the glass. Only use höfats liquid fuel in the SPIN to avoid heavy soot formation.
Soot residues that can no longer be removed from the glass cylinder may have baked into the glass. If so, replace the glass cylinder and remove future soot residue immediately. If possible, use liquid fuels from höfats to avoid heavy soot formation.
Minimal dirt on the cover of the Bio-Burner has no effect on the flame. Use a hair brush to remove dirt from the Bio-Burner cover. The Bio-Burner must not be put in the dishwasher.