Ningbo Cstar Imp Exp SL375 True Wireless Earbuds User Guide

June 6, 2024
Ningbo Cstar Imp Exp

Ningbo Cstar Imp Exp SL375 True Wireless Earbuds

GETTING STARTED

  1. Micro USB charging port
  2. Charging Case LED indicators
  3. Charging Case Power Button
  4. Left earbud LED indicator
  5. Left control button
  6. Right earbud LED indicator
  7. Right control button
  8. Wireless receive area

CHARGING YOUR CASE

  1. Charge on the go charging case, with the included micro USB cable for 2-3 hours. (LED (2A) will blink red) Do not charge longer than suggested time. Do not charge overnight
  2.  is illuminated solid red battery case is fully charged.— Charge the charging case with wireless, place the case on the  wireless charger for charging. The LED indicator will be lit red during charging and turned off after fully charged.

CHARGING YOUR EARBUDS

earbud LED indicators (4, 6) will illuminate Red, indicating that  the earbuds are charging properly. When Earbuds LEDs (4, 6) turn solid blue, earbud batteries are fully charged

MONO MODE

(SINGLE EARBUD USE)

  1. Remove earbud from charging cradle or power on by pressing the control button (7) or (5) for 3 seconds depending on which earbud your using.
  2. Once earbud is powered on, proceed to PAIRING
  3. Remove both earbuds from charging cradle and place them in your ears.
  4. Make sure Bluetooth Search Mode is turned
  5. Earbud LEDs will flash Red and Blue to indicate that they are in Link mode.
  6. Earbuds will automatically link together after a few seconds,and earbuds will have a tone (On e earbuds will flash red and blue, another earbuds will turn off LED indicator)
  7. Once Earbuds are linked together you may proceed to pairing with your mobile device.

PAIRING

  1.  Enable Bluetooth search mode on your mobile device and search for pairing name “Oros TWS Earbuds ” and select it on your mobile phone. Once the earbuds are successfully paired a notification will sound .
  2. Now you can enjoy your true wireless Bluetooth Earbuds.

OPERATING BLUETOOTH EARBUDS

Function Operation
Power On Press (5) or ( 7) for 3 seconds
Power Off Press (5) or ( 7) for 5 seconds
Play/Pause Single press (5) or (7)
Answer Single press (5) or (7)
Reject Press (5) or ( 7) for 2 seconds
Earbuds LED indications (4) & (6)
Power On Red and Blue LED will flash altemately
Link Mode Flashing Blue + Red
Two earbuds paired successfully each other One earbuds will flash red and

blue,another earbuds will turn off LED indicator
Paired Successfully| LED Off
Power Off| LED Off
Earbuds in Cradle|
Charging| Flash Red
Fully Charged| Solid Red

Earbuds LED indications (4) & (6)
Power On Red and Blue LED will flash altemately
Link Mode Flashing Blue + Red
Two earbuds paired successfully each other One earbuds will flash red and

blue,another earbuds will turn off LED indicator
Paired Successfully| LED Off
Power Off| LED Off
Earbuds in Cradle|
Charging| Flash Red
Fully Charged| Solid Red

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.
  5. To assure continued compliance, any changes or modifications not expressly approved by the party.Responsible for compliance could void the user’s authority to operate this equipment. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  6. This device may not cause harmful interference, and
  7.  This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can ben used inthe portable exposure condition with restiction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals