i-PRO WV-CW7S Dome Cover ClearSight Coating Instruction Manual
- June 13, 2024
- i-PRO
Table of Contents
i-PRO WV-CW7S Dome Cover ClearSight Coating
Product Information
- Model No.: WV-CW7S / WV-CW7SN
- Features : Smoked dome cover with ClearSight coating (Rain wash coating)
Specifications
- Ambient operating temperature –45 °C to +60 °C {–49 °F to 140 °F}
- Mass Approx. 74 g {0.16 lbs}
- Dimensions Diameter: 115 mm {4-17/32 inches} Height: 60 mm {2-3/8 inches} Dome radius 42 mm {1-21/32 inches}
Standard Accessories
- Operating Instructions (1 set)
- Precautions (1 leaflet)
- Waterproof rubber (for replacement, 1 pc)
Product Usage Instructions
- Before attempting to connect or install this product, read the instructions carefully and save the manual for future use.
- Refer installation work to the dealer as it requires technique and experience to avoid fire, electric shock, injury, or product damage.
- To install the dome cover, follow these steps:
- Remove the enclosure from the camera body by loosening the 4 enclosure fixing screws using the provided bit, and then remove the enclosure.
- Remove the dome cover from the camera body.
- Replace the dome cover:
- Attach the waterproof rubber provided with the new dome cover to the enclosure without distortion or deformation. Do not reuse the waterproof rubber removed from the enclosure. Use the new waterproof rubber provided.
- Remove the protection film covering outside the new dome cover, but keep it for later use. Handle the new dome cover carefully to avoid scratching inside and outside. Attach the removed protection film back to the outside of the dome cover.
- Refer to the camera’s Installation Guide for subsequent procedures, including the installation of the camera body.
Precautions
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this
may cause fi re, electric shock, injury, or damage to the product.
Be sure to consult the dealer.
Installations
The following are installation instructions using WV-S2531LN as a
representative example. Refer to manuals of each model upon installation.
Note:
When the smoke type dome cover is used, the reach distance of IR will become
shorter and the ambient illuminance for the day & night switchover will become
lower compared to the standard clear type dome cover. Please reconfirm the
performance after reinstalling the enclo-sure to the camera.
-
Step 1
Remove the enclosure from the camera body
Loosen the 4 enclosure fixing screws using the bit provided with the camera, and then remove the enclosure from the camera body. -
Step 2
Remove the dome cover
Remove the 3 dome cover fixing screws (2 with-out washers, 1 with washer), and then remove the dome cover holding plate, the light-blocking sheet (WV- SFV631LT/ WV-SFV631L/
WV-SFV611L only), the dome cover and the waterproof rubber from the enclosure.
(The Dome cover holding plate and the camera body are connected with the installation auxiliary wire. Please pay attention that the installation auxiliary wire will be removed at the moment when the dome cover fixing screws are removed.)
Keep the removed dome cover holding plate, the light-blocking sheet (WV- SFV631LT/ WV-SFV631L/ WV-SFV611L only), 3 fixing screws until using them in step 3. -
Step 3
Replace the dome cover-
Attach the waterproof rubber provided with the new dome cover to the enclosure. Make sure that the waterproof rubber is attached without distortion or deformation. Do not use the waterproof rubber removed from the enclosure. Use the new waterproof rubber provided with the new dome cover.
-
Remove the protection film covering outside the new dome cover.
Keep the removed protection film until using it upon the installation.
(Handle the new dome cover with care not to scratch inside and outside.) -
Fit the new dome cover, the light-blocking sheet (WV-SFV631LT/ WV-SFV631L/WV-SFV611L only) and the dome cover hol-ding plate together while aligning the holes on them to the 2 protrusions inside the enclosure, and then fix them using the 2 dome cover fixing screws (without washers).
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}) -
Attach the protection film removed in step3-2 back to the outside the dome cover.
-
When fixing the third dome cover fixing screw (with washer), fix the installation auxi-liary wire together.
When fixing with the screw, make sure that the flat face of the fixing terminal is the sur-face side of the dome cover holding plate. Make also sure that the fixing terminal is not on the projection of the dome cover holding plate. (Refer to the diagram below.) (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
-
-
Step 4
Fit the enclosure back to the camera body Fix the enclosure onto the camera body using the 4 enclosure fixing screws.
The recommended tightening torque for the enclosure fixing screws is 0.78 N·m {0.58lbf·ft}. -
Refer to the Installation Guide of the camera for the subsequent procedures including the installation of the camera body.
IMPORTANT:
- Defocus may be caused by the reinstalled enclosure. After installing the enclosure, activate the auto focus function from the setup menu.
- Remove the protection film covering the outside of the dome cover after completing the installation.
- Wipe out with a soft cloth when cleaning adhesion of dirt such as a fingerprint. (WV-CW7S only)
- Refer to “Precautions”(leaflet) and clean the dome cover. (WV-CW7SN only)
For U.S. and Canada:
i-PRO Americas Inc.
For Europe and other countries:
i-PRO EMEA B.V.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>