ROBUS RS100LEDCCT3E-01 Golf Slim 10w-15w Led Cct Selectable 3000K Instruction Manual

ROBUS RS100LEDCCT3E-01 Golf Slim 10w-15w Led Cct Selectable 3000K

PLEASE READ THE INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN THEM FOR FUTURE REFERENCE. Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician

Note:
Product technical information and specification may change over time without prior notification. For the latest technical information please visit our website www.robus.com or robusdirect.com

• -5°C < Ta < +35°C, 220V – 240V ~ 50/60Hz, Class II, IP65, Battery Warranty: 2 Years Luminaire is non-dimmable Suitable for mounting on a normally flammable surface.

Installation

1.  Ensure the mains supply is switched off before commencing work.

2.  Ensure there is at least 100mm of free space around the luminaire location.

3.  Remove trim/ diffuser from the base of the fitting.

4.  Drill cable entry and mounting holes in the base.

5.  Mark fixing hole positions on the wall, check the location of buried cables, pipes or other building services before drilling.

6.  Feed supply cables through the cable entry hole and attach the base to the surface of the wall.

7.  Write installation date on battery and connect the battery.

8.  Connect wires from unswitched supply to terminals: brown to PL, Blue to N. For fitting always on, link terminal SL to terminal PL. For fitting controlled by switch, connect switched live wire to terminal SL and permanent live to PL.
   Note: if the SL terminal is not connected, the fitting works as non- maintained.

9.  There is an additional terminal, that can be used for earth connection.

10.  Move the switch on top of the driver to select color temperature: 3000K, 4000Kor 6500K.

11.  Refit trim/ diffuser to base.
    Attention: In order to protect the battery life, please disconnect the battery if the power supply shut off over 3 days.

WARNING: DO NOT CHANGE CCT WHEN THE FITTING IS ON.

Switch on supply:
The green led should come on indicating the correct battery charge status, all LEDs will come on. When supply to the switched live PL is lost, battery will operate fitting in emergency mode.

Market Surveillance:
These products contain light sources of energy efficiency as detailed below.
RS100LEDCCT3ES-LS: Class E; RS150LEDCCT3ES-LS: Class E Disconnect driver input and output connections. Remove LED plate

Testing
The emergency lighting must be inspected and tested regularly in accordance with local codes of practice. Note: for safety reasons tests should be carried out during daylight hours.
The minimum recommended test schedule is as follows:
After installation, allow 24 hours to ensure full battery charge and then interrupt the supply; the maximum duration time is 3 hours. Check that LEDs are still lighting.

1.  Daily check that the charge indicator LED is working.
2. Monthly, interrupt mains for a short period and check LED lights.
3.  Annual 12-month check, full-duration test. Interrupt mains supply, LEDs will light and should last for a minimum of 3 hours of operation: batteries must be replaced when they can no longer support 3-hour operation.
4.  Complete record sheet on installation and retain in maintenance file.
5.  Update file with ongoing test records for inspection by fire officer or another duly authorized person.

Information for the Product user:

1.  Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed-out wheelie bin symbol).
2.  Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3.  This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
4.  The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations

The Installation must be carried out by a qualified electrician

Documents / Resources

| ROBUS RS100LEDCCT3E-01 Golf Slim 10w-15w Led Cct Selectable 3000K [pdf] Instruction Manual
RS100LEDCCT3E-01, RS150LEDCCT3E-01, Golf Slim 10w-15w Led Cct Selectable 3000K
---|---

References

• robusdirect
• ROBUS: Home to Best-in-Class LED Lighting and Customisation - Robus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>