ARDESTO CHB-2000MBD, CHB-2000MWPD Electric Convector Instruction Manual
- June 3, 2024
- ARDESTO
Table of Contents
- SAFETY REQUIREMENTS
- GENERAL INSTRUCTIONS
- IT IS NOT ALLOWED TO:
- TECHNICAL SPECIFICATIONS
- PACKAGE CONTENTS
- DESCRIPTION
- BEFORE THE FIRST USE
- SETTING
- USING THE CONVECTOR
- AUTO SWITCH FUNCTION
- CLEANING AND CARE
- TRANSPORTATION AND STORAGE
- Warranty conditions:
- WARRANTY CARD
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ELECTRIC CONVECTOR
Instruction manual CHB-2000MBD
CHB-2000MWPD
SAFETY REQUIREMENTS
Before connecting the convector to the power supply, be sure to visually check
the power cord and the convector for mechanical damage. If there are damages,
contact an authorized service center for repair. Before repairing damage, it
is not allowed to connect the convector to the power supply.
Disconnect the convector from the power supply during its maintenance, wet
cleaning of the room near the convector installed on the floor. Disconnect the
electric convector from the power supply by holding the plug of the power
cord.
Do not use this heater near bathtubs, showers or swimming pools.
Do not use the device in rooms with high humidity. Place the device at a
distance of not less than 1.5 meters from open flame. Provide that no water
gets on the device body. If any water gets on the device body, unplug the
device before touching it and only then wipe water drops. Always use the
supporting wheels when placing the device and place the device on a flat
steady surface. Before using the device make sure that the wheels are
installed properly.
Do not use the device in the rooms where inflammable substances are kept or
used. Do not use the device, if the room temperature is over +30°C. Do not
leave the switched on device when sleepingand do not place it near a sleeping
person. Do not allow paper or foreign objects inside the convector.
Do not use the convector for other purposes (the convector is not intended for
outdoor use). Do not operate the convector with damaged power cord. Make sure
that the power cord does not not touch sharp corners and heated surfaces of
the convector.
WARNING! If the power cord is damaged, it should be replaced by the
manufacturer, an authorized service center or similar qualified personnel in
order to avoid danger. This device can be used by children over 8 years of age
and persons with physical or sensory or mental disabilities or with
insufficient experience and knowledge, if they are under constant supervision
or instructed in the safe use of the device and they understand the possible
dangers. Children should be supervised to ensure they do not play with the
product. Cleaning and customer servise should not be performed by children
without supervision. Children under 3 years old should not be close to the
appliance, except when they are under constant supervision. In addition,
children should be provided with appropriate supervision or instructions for
the safe use of the appliance, and they should be aware of the risks that may
arise when using the appliance. Children aged 3 to 8 years may only switch the
appliance on/off and only if the appliance is placed/installed in its normal
working position. Children aged 3 to 8 years should not connect the appliance
to the power supply (power outlet), adjust and clean the appliance, or perform
maintenance.
ATTENTION! Parts of this product may be very hot and cause burns.
Particular attention should be paid to where children and vulnerable persons
are.
WARNING! To prevent overheating, do not cover the convector!
WARNING! This heater is not equipped with a room temperature control
device. This heater should not be used in small spaces with people who are
unable to leave the space on their own, unless they are constantly supervised.
WARNING! Before installing and operating this product, please read this
«User Manual» (hereinafter referred to as «the manual») carefully.
Due to the continuous umprovement of the product, there can be made changes in
the design of the product that are not reflected in this manual without
reducing its consumer properties.
GENERAL INSTRUCTIONS
The convector is intended only for additional heating of rooms, it is not
meant for operation as a main heating device.
The convector is installed on the floor on support plates with wheels.
Optionally, it can be installed on the wall using mounting brackets (not
included in the standard equipment).
When buying a convector, require a check of its operability, compliance of the
delivery set with the “Package contents” section of this manual, and the
absence of mechanical damage. Check the availability of warranty card,
completeness and correctness of its filling. The convector model should comply
with the data indicated in the warranty card. The warranty card is valid only
if there is correctly and legibly specified sales data, clear seals of the
seller.
After filling out the warranty card, it is not allowed to make any amendments,
additions, delete and rewrite the data added by the seller.
Keep the cashier’s check, this manual, warranty card and packaging during the
warranty period of the convector. Lost documentation attached to the convector
upon sale is not restored.
REMEMBER: if you fail to comply with the above recommendations or if
there is mechanical damage to the convector, you lose the right to warranty
service.
IT IS NOT ALLOWED TO:
- Place the heater directly under the outlet.
- Partially or complety cover, clog holes in the intake and exhaust grids.
- Place flammable substances and objects near the convector.
- Use convectors in the immediate vicinity of the bathtub, shower or swimming pool.
- Touch the plug of the power cord and the convector with wet hands.
- Do not use the device outdoors or on wet surfaces.
- Do not use the heater surface for drying wet clothes, towels etc. You can dry only small items of clothes or furniture and only using the bracket for drying small things (3).
TECHNICAL SPECIFICATIONS
Power supply | 220-240 V~50-60Hz |
---|---|
Rated input power | 2000W |
Heating area | up to 25 sq.m. |
PACKAGE CONTENTS
Electric convector – 1 pc.
Support plates with wheels – 2 pcs.
Bracket for drying small things – 1 pc.
Water tank – 1 pc.
Instruction manual (warranty card included) – 1 pc.
DESCRIPTION
- Support plates with wheels
- Hot air outlet grid
- Bracket for drying small items
- Operation mode switch «I/0/11»
- Body
- Water tank (for natural air humidification)
BEFORE THE FIRST USE
After device transportation or storage at low temperature keep it for at least three hours at room temperature.
- Unpack the device.
- Check the device for damages, do not use it in case of damages.
- Make sure that the device operating voltage corresponds to the voltage of your mains.
- Make sure that the operation mode switch (4) is set to the position «0» (the device is switched off).
SETTING
Stand mode
- Turn the device over.
- Insert the supporting plates with wheels (1) into the openings on the convection fan heater body.
- Turn the device over and set it on the wheels.
USING THE CONVECTOR
- Before switching the device on, make sure that your home mains voltage corresponds to the device operating voltage, and the switch (4) is in theposition «0» (the device is switched off). Insert the power plug into the mains socket.
- Set the operation mode switch (4) into the necessary position:
– 0 – the fan heater is switched off,
– I – minimum heating power (1000 W),
– II – maximum heating power (2000 W).
To dry small items, install the bracket (3) on the convector body (5).
Note: do not hang wet clothes, large towels etc. on the bracket (3).
To use the natural humidification function, install the water tank (6) on the
convector body (5).
Notes:
- Do not install the water tank (6) if you do not plan to use this function.
- Pour water into the water tank (6) only when it is installed on the device body (5), the convector is switched off and the power cord is unplugged.
- Do not pour water up to the edges of the water container (6), make sure that the water level is no more than 1 cm from the edge of the container. After using the device, set the switch (4) to the «0» position, then unplug the device.
Notes:
While the first switching on the heating element burns, therefore occurrence
of a small amount of smoke or foreign smell is possible. It is normal, after
some time the smoke and smell will disappear. It is recommended to ventilate
the room.
Do not open windows and doors when the device is operating; otherwise you will
not get the desired results, due to cold air inflow.
AUTO SWITCH FUNCTION
The device is equipped with an automatic switch that switches the device off
when it is dropped or considerably tilted. When the device is back in the
vertical position, it will be switched on.
If the device is not switched on, it may mean that there are damages in the
convection fan heater. In this case contact an authorized service center to
repair the device.
CLEANING AND CARE
- Before cleaning, disconnect the device from the mains and let it cool down.
- At least once a month, clean the convector grids from dust with a brush and a vacuum cleaner with a corresponding attachment.
- Do not use abrasive or aggressive materials that can damage the convector coating.
- Wipe the outer surface of the device (5) with a damp cloth and then wipe the fan heater dry.
- Do not immerse the fan heater body, the power cord or the plug into water or any other liquids. Provide that water does not get into the fan heater body to avoid electric shock.
TRANSPORTATION AND STORAGE
Convectors in the manufacturer’s packaging can be transported by all types of
covered vehicles, which ensure their protection against atmospheric
precipitation and mechanical damage, in accordance with the rules for the
carriage of goods in force on this type of transport. Transportation is
allowed at temperatures from 50 °C to -50 °C nd relative humidity not more
than 80%, in accordance with the handling signs on the package, and with the
exception of shock and movement inside the vehicle. Convectors should be
stored in the manufacturer’s packaging in dry, heated rooms at temperatures
from 5 °C to 40 °C and relative humidity not exceeding 80 %.
Keep the device out of reach of children and disabled persons. Storage of
convectors in rooms together with liquids and substances, the evaporation of
which can cause corrosion of structural elements is not allowed. Before using
the fan heater next time, it is recommended to check the device operability
and integrity of the power cord isolation and the power cord plug.
DISPOSAL
**** The product does not contain materials requiring special disposal
technologies. The product does not contain precious metals. Upon
decommissioning, the product should be disassembled, followed by sorting the
scrap into non-ferrous, ferrous metals and non-metals, and their disposal in
accordance with the norms, rules and methods applicable at the disposal sites.
Warranty conditions:
The plant guarantees normal operation of the product within 12 months from the
date of the sale, provided that the consumer complies with the rules of
operation and care provided by this Manual.
Service life of the product is 5 years.
In order to avoid any misunderstanding we kindly ask you to carefully study
the Owner’s Manual, the terms of warranty, and check the correctness of
filling the Warranty Card. The Warranty Card is valid only if the following
information is correctly and clearly stated: model, serial number of the
product, date of sale, clear seals of the company-
seller, signature of the buyer. The model and serial number of the product
must correspond to those specified in the Warranty Card.
If these terms are violated, and if the information specified in the Warranty
Card is changed, erased or rewritten, the Warranty Card is considered invalid.
Setup and installation (assembly, connection, etc.) of the appliance are
described in the attached documentation; they can be carried out both by the
user, and by specialists having the necessary qualification sent by USC or
selling companies (on a paid basis). In this case, the person (the
institution) installing the appliance shall be responsible for the correctness
and quality of installation (setup). Please pay attention to the importance of
the correct installation of the appliance, both for its reliable operation,
and for obtaining warranty and free service. Require the installation
specialist to enter all the necessary information about the installation in
the Warranty Card.
In case of failure of the appliance during the warranty period by the fault of
the manufacturer, the owner is entitled to free warranty repair upon
presentation of the correctly filled Warranty Card together with the appliance
in the factory configuration packed in the original packaging to the warranty
workshop or the place of its purchase. Satisfaction of the customer’s claim
due to the fault of the manufacturer shall be made in accordance with the law
«On Protection of Consumers’ Rights». In the case of warranty repair the
warranty period shall be extended for the period of repair and shipment.
WARRANTY CARD
Dear Buyer! Congratulations on your purchase of the ARDESTO brand appliance, which was designed and manufactured in accordance with the highest quality standards, and we thank you for choosing this particular instrument. We ask you to keep the coupon during the warranty period. When purchasing a product, require a full warranty card.
-
Warranty service is carried out only if there is a correctly and clearly filled original warranty card, which indicates: product model, date of sale, serial number, warranty service period, and the seller’s seal. *
-
The service life of household appliances is 5 years.
-
The product is intended for consumer use. When using the product in commercial activities, the seller / manufacturer does not bear warranty obligations, after-sales service
is performed on a paid basis. -
Warranty repair is carried out within the period specified in the warranty card for the product in an authorized service center on the conditions and terms determined by
applicable law. -
The product is withdrawn from the warranty in case of violation by the consumer of the operating rules set forth in the instruction manual.
-
The product is removed from warranty service in the following cases:
• misuse and non-consumer use;
• mechanical damage;
• damage caused by the ingress of foreign objects, substances, liquids, insects;
• damage caused by natural disasters (rain, wind, lightning, etc.), fire, domestic factors (excessive humidity, dust, aggressive environment, etc.)
• damage caused by non-compliance of power and cable network parameters with state standards and other similar factors;
• when operating equipment in the power supply network with a missing single ground loop;
• in case of violation of seals installed on the product;
• lack of serial number of the device, or inability to identify it. -
The warranty does not cover consumables and accessories, as well as filters, shelves, drawers, stands and other containers for storing products.
-
The warranty period is 12 months from the date of sale.
- Tear-off maintenance tickets are provided by an authorized service center.
The completeness of the product is checked. I have read the terms of the
warranty service, no complaints.
Customer Signature__
Warranty card
Product informatio——-
Product————
Model—————
Serial number————–
Seller Information————–
Trade organization name———–
The address————
Date of sale————-
Seller stamp————–
Coupon № 3
Seller stamp————-
Date of the application————
Cause of damage—————
Date of completion————-
Coupon № 2
Seller stamp————–
Date of the application—————–
Cause of damage————-
Date of completion————
Coupon № 1
Seller stamp————–
Date of the application———-
Cause of damage——-
Date of completion————
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>