SEGWAY JH0002 Bluetooth Fingerprint U-Lock User Manual
- June 6, 2024
- Segway
Table of Contents
Segway Bluetooth Fingerprint U-Lock
User Manual
Before using the product, please read the manual carefully and keep it for future reference.
Product Overview
Thank you for choosing Segway Bluetooth Fingerprint U-Lock (referred to as “the fingerprint lock” in this manual). This product is easy to use and energy-efficient. It has high sensitivity, and a high recognition rate, and can be unlocked in under a second.
Accessories:
- Please keep the spare keys in a safe place. Segway does not sell or provide replacement keys.
The pictures in this manual are for illustration purposes only. The actual product, app features, and interface may differ.
First Use
When using it for the first time, you can use any fingerprint to unlock it. Please follow the steps below:
-
Remove the protective cover from the fingerprint panel.
-
Press the fingerprint panel until you hear a long beep and the indicator light turns blue.
-
After unlocking, please follow the instructions to activate the lock and register your fingerprints.
App Activation
Scan the QR code above to install the Segway-Ninebot app (referred to as “the app” in this manual) . Follow the prompts to activate the fingerprint lock and complete owner authentication. Keep your phone close to the lock to ensure a Bluetooth signal.
-
After installing the app, please register or log in.
-
Tap “Search Device” to find and connect your fingerprint lock. After the connection is successful, the indicator light turns yellow, and you will hear one beep.
-
Follow the prompts to complete product activation and owner authentication.
Registering a Fingerprint
Open the app and go to the fingerprint lock main page. Go to “Fingerprint
Management” > “Add New Fingerprint” and follow the prompts.
After a fingerprint has been successfully registered 6 times, it can be used
to open the lock. The indicator light will turn blue and you will hear a long
beep.
-
When registering your fingerprint, make sure to fully cover the fingerprint sensor with your finger at different angles.
-
Make sure your fingers are clean and dry.
NOTE:- You can add, delete, and name the fingerprints, and view unlocking history in the app.
- If the fingerprint lock does not respond, check its battery level in the app. If the indicator light flashes red and beeps continuously, please charge the device soon.
- Before giving away or reselling the fingerprint lock, tap the “icon on the fingerprint lock interface, and then tap “Device Settings” > “Restore Factory Settings” to clear all records.
Unlocking
You can use any of the following methods to open the fingerprint lock:
a. Verify the fingerprint.
b. Open the app and tap the “Unlock” icon on the fingerprint lock interface.
c. Remove the rubber plug and use the spare key to unlock.
NOTE:
If the verification fails 10 consecutive times, the fingerprint lock will be
frozen for 60 seconds. During this time, you can open the lock via the app or
with a spare key.
Locking
Pass the lock shackle through the wheel or hub, and then align it with the
lock head. Press the shackle into the head to lock.
Ninebot KickScooter series
Ninebot eloped series
CAUTION: To prevent damage, keep the fingerprint lock off the ground, and avoid heavy rain and large puddles.
Charging
Use the USB cable to connect a USB charger to the charging port. Then, plug
the charger into a power outlet.
CAUTION：
The output voltage of the charging plug should not exceed 5 V, and the
charging current should not exceed 1 A.
The indicator light stays red during charging and turns off when charging is
complete.
WARNING
- Store the fingerprint lock in a dry place away from flammable and explosive materials.
- Keep the fingerprint lock dry and clean. You can clean it with a dry cloth or paper towel. Do not wipe with water, alcohol or other chemicals.
- Avoid exposure to liquids.
- Keep the charging port and keyhole free from dust and debris.
- Cover the fingerprint panel protective cover and keyhole when not in use.
Product Specifications
| Product name | Segway Bluetooth Fingerprint U-Lock |
|---|---|
| Model | PJ02ZWS |
| Applicable models | Ninebot eloped series Ninebot KickScooter series |
| Product dimensions (L x W x H) | 8.7 x 5.7 x 1.2 in (221 x 145 x 30 mm) |
| Lock shackle diameter | 0.5 in (12 mm) |
| Net weight | Approx. 2.9 lbs (1.3 kg) |
| Materials | Zinc alloy, TPU, stainless steel, ABS |
| Storage temperature | -4-185 °F (-20-85 °C) |
| Working temperature | 14-140 °F (-10-60 °C) |
| Charging time | Approx. 4 hours |
| Resolution | 508 DPI |
| Pixels | 96*96 |
| Fingerprint capacity | 10 fingerprints |
| IP rating | 1P65 |
| Battery pack parameters | Rated voltage: 3.7 V |
Charging temperature: -4-140°F (-20-60°C)
Rated capacity: 400 mAh
Rated energy:1.48 Wh
Charging port| Micro USB
Certifications
Federal Communications Commission (FCC) Compliance Statement for the USA This
device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment
NOTE This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
Industry Canada (IC) Compliance Statement for Canada This device complies with
Industry Canada license-exempt RSS standard (s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
Neither Segway Inc. nor Ninebot is responsible for any changes or
modifications not expressly approved by Segway Inc. or Ninebot. Such
modifications could void the user’s authority to operate the equipment.
FCC ID: 2AU2Y-JH0002
IC: 25633-JH0002
Trademark and Legal Statement
Ninebot is the registered trademark of Ninebot (Tianjin) Tech. Co., Ltd.; The Rider Design is the registered trademarks of Segway Inc.; The respective owners reserve the rights of their trademarks referred to in this manual. We have attempted to include description and instructions for all the functions of Segway Bluetooth Fingerprint U-Lock at the time of printing. However, due to constant improvement of product features and changes of design, your Segway Bluetooth Fingerprint U-Lock may differ slightly from the one shown in this document. Please visit www.segway.com to download the latest user materials. ©2020 Ninebot (Beijing) Tech Co., Ltd. All rights reserved.
After-sales Service
For after-sales service information, please visit our official website.
The Americas: Tel: 1-888-523-5583
Web:https://www.segway.com/consumertechsupport/
Others: www.segway.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>