SEGWAY P100SE KickScooter User Manual
- June 3, 2024
- Segway
Table of Contents
SEGWAY P100SE KickScooter
The manufacturer reserves the right to make changes to the product, release firmware updates, and update this manual at any time. Visit www.segway.com or check the Segway-Ninebot app to download the latest user materials. You must install the app, activate your KickScooter, and obtain the latest updates and safety instructions.
Diagram and Functions
Handlebar Functions
Name | Function | Operation method |
---|---|---|
Power Button | Power on/off | Press the Power Button to power on the scooter. |
Press and hold to power it off.
- Available only when the scooter is not in Anti-theft mode.
Wake up the dashboard| Press the Power Button to wake up the dashboard when
the dashboard automatically dims.
Mode Switching Button|
Switch between speed modes
| Press the Mode Switching Button twice to switch mode.
Multi-function Button| Turn on/off ASSIST mode| Enabling ASSIST mode via the
Segway-Ninebot app:
When the scooter is at a complete stop, press the Multi-function Button to turn on ASSIST mode.
Turn off ASSIST mode: Release the throttle and squeeze brake levers to stop, then press the Multi-function Button again.
Turn on/off the headlight| Rotate the Multi-function Button
clockwise/counterclockwise to turn off/on the headlight.
Turn on/off the adaptive headlight feature| Rotate the Multi-function Button
clockwise/counterclockwise and hold it for 3 seconds to turn off/on the
adaptive headlight feature.
- When the scooter is activated, this feature is turned on by default.
Confirm the password| Press the Multi-function Button to confirm the password
after entering the password with the Direction Indicator Button successively.
USB Port| Charging| Connect your device to the USB Port for charging.
Throttle| Speed up| Press and hold the throttle to speed up.
NFC Area| Interact with the NFC card to power on/off|
Tap the NFC card on the NFC Area to power on/off the scooter.
Interact with the NFC card to unlock| Tap the NFC card on the NFC Area to
unlock the scooter.
Horn Button| Turn on the horn| Press the Horn Button, the scooter will beep.
Direction Indicator Button| Turn on the left/right direction indicator| Press
the left/right side of the Direction Indicator Button, the left/right
direction indicator will flash, and automatically turns off after 5 seconds.
Enter the password| Press the left/right side of the Direction Indicator
Button (left is minus, right is plus) to enter the password.
Dashboard
Symbol | Name | Meaning | Description |
---|
| POWER Progress Bar|
The symbol displays the motor output power of the scooter.
| Speedometer| The symbol displays the current speed of the scooter.
| |
When the icon flashes, it means the scooter enters Anti-theft mode.
|
When the scooter is powered off after 30 seconds:
If the scooter is moved or touched by someone, it will enter to Anti-theft mode. At this point, the scooter will start beeping and the front and rear direction indicators will flash, and the motor will be locked automatically.
| |
| |
| |
Lock| When the icon lights up, it means the scooter is locked.|
When locked via the Segway-Ninebot app or in the unlocking state via password,
the scooter will keep beeping and the tail light will flash.
Unlock the scooter with the following methods:
- Press the Power Button to wake up the dashboard, the dashboard will display
the digit “0” by default, then enter the four-digit password 1-2-3-4 with the
Direction Indicator Button and confirm the password with the Multi-function
Button successively.
Note: After activating your scooter, enable/disable the unlock with a password feature via the Segway-Ninebot app and set your password.
Otherwise, you cannot unlock your scooter with a password. - Tap the NFC card on the NFC Area.
- Unlock via the Segway-Ninebot app.
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| Temperature Warning| It indicates that the battery temperature has reached
60°C (140°F) or is below 0°C (32°F).
Symbol| Name| Meaning| Description
---|---|---|---
| USB Port Icon| When the USB port icon lights up, it means that the device
(not fully charged) is connected to the USB port.
| Bluetooth| It indicates that the scooter is connected to the Segway-Ninebot
app.
| Warning| The symbol indicates that the scooter has detected an error. The
error code will display on the dashboard. Please contact the after-sales
service for repair.
| Remaining battery
power| The symbol displays the remaining battery power in battery bar.
| Adaptive Headlight| When the icon flashes, it means the Adaptive headlight
feature is turned on.| When this feature is turned on, the headlight will work
automatically to adapt to a variety of situations and conditions and help
illuminate the way.
Speed Modes Introduction
Mode/model | P100SE (Speed limit) | Switching methods |
---|---|---|
3–5 km/h |
(1.9–3.7 mph)
| Enable/Disable Walk mode via the Segway-Ninebot app.
Note: The headlight is always on and the tail light will keep flashing in Walk
mode.
| 3–5 km/h
(1.9–3.7 mph)
| Enabling ASSIST mode via the Segway-Ninebot app:
When the scooter is at a complete stop, press the Multi-function Button to
turn on ASSIST mode.
Note: When turned on, the scooter will beep once and the front and rear
direction indicators will flash once. Turn off ASSIST mode:
Release the throttle and squeeze brake levers to stop, then press the Multi-
function Button again.
ceo| 18 km/h (11.2 mph)| Press the Mode Switching Button twice.
drive| 20 km/h (12.4 mph)| Press the Mode Switching Button twice.
sport| 25 km/h (15.5 mph)| Press the Mode Switching Button twice.
Specifications
| Item| Parameter
---|---|---
Product| Name| Segway Kick Scooter
Model| P100SE
Length × Width × Height| Approx. 1184 × 634 × 1287 mm (46.6 × 25 × 50.7 in)
Folded: Length × Width × Height| Approx. 1184 × 634 × 640 mm (46.6 × 25 × 25.2
in)
Net Weight| Approx. 32.9 kg (72.5 lbs)
Rider| Max. Payload| 120 kg (265 lbs)
Recommended Age| 18–60 years old
Required Height| 160–200 cm (5’2”–6’6”)
Machine| Wheelbase| 900 mm (35.4 in)
Ground Clearance| 153 mm (6 in)
Max. Speed| Approx. 25 km/h (15.5 mph)
Typical Range[1]| Approx. 100 km (62.1 miles)
Max. Slope| Approx. 23%
Traversable Terrain| Bicycle lanes, parks, campuses and most of the flat road
conditions and typical Belgian roads
Operating Temperature| -10 to 40°C (14 to 104°F)
Storage Temperature| -10 to 50°C (14 to 122°F)
IP Rating| IPX5
Duration of Charging| Approx. 7 h
Battery| Model| NCDF4825B
Nominal Voltage| 47.2 V
Max. Charging Voltage| 54.6 V
Nominal Energy| 1086 Wh
Nominal Capacity| 23 Ah
Charging Ambient Temperature| 0–43°C (32–109°F )
Battery Management System| Over-heating, short circuit, over-current, over-
discharge and over-charge protection
Motor| Motor Type| Brushless DC (BLDC) motor
Nominal Power| 0.65 kW, 650 W
Charger| Type| Built-in
Input Voltage| 100–240 V~50–60 Hz, 2.0 A MAX.
Max. Output Voltage| 54.6 V
Rated Output| 53.5 V 3 A
| Item| Parameter
---|---|---
Charger| Output Power| 0.16 kW, 160 W
Model| NBW54D603D0D
Tire| Type| 10.5-inch Self-sealing tubeless tires
Tire Pressure| 30–45 psi
Material| Rubber
Others| Speed Modes| Walk mode, ASSIST mode, ECO mode, DRIVE mode and SPORT
mode
Suspension System| Front and rear torsion bar suspension
Brake System| Disc brake & Electric brake
- Typical Range: tested while riding with a full battery, 75 kg (165 lbs) load, 25°C (77°F), at the speed of 9.9 mph (16 km/h)
on average on pavement.
- Some of the factors that affect range include speed, number of starts and stops, ambient temperature, etc.
Common Failures
Error code | Possible causes |
---|---|
10 | BLE Bluetooth communication error |
11 | Motor 1A phrase current sampling failure |
12 | Motor 1B phrase current sampling failure |
13 | Motor 1C phrase current sampling failure |
14 | Throttle Hall sensor abnormality |
15 | Brake Hall sensor abnormality |
18 | Hall sensor abnormality |
21 | BMS communication error |
22 | BMS password error |
23 | BMS default serial number |
24 | System voltage detection abnormality |
26 | Flash storage error |
27 | Control board password error |
28 | Motor MOS driver upper bridge short circuit |
29 | Motor MOS driver lower bridge error |
31 | Program skip error |
35 | Vehicle default serial number |
39 | Battery temperature sensor error |
41 | Turn signal abnormality |
42 | Headlight abnormality |
45 | Abnormal bus current op-amp circuit |
Certifications
-
This product is certified to ANSI/CAN/UL-2272 by TUV Rheinland.
-
The battery complies with UN/DOT 38.3.
-
The battery complies with ANSI/CAN/UL-2271.
-
European Union Compliance Statement
-
Information on Disposal for Users of Waste Electrical & Electronic Equipment
-
This symbol on the product or on its packaging indicates that used electrical and electronic products should not be mixed with unsorted municipal waste. For proper treatment, it is your responsibility to dispose of your waste equipment by arranging to return it to designated collection points.
-
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.
-
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.
-
Please contact your local authority for further details of your nearest designated collection point.
-
Battery recycling information for the European Union
-
This symbol means that batteries and accumulators, at their end-of-life, should not be mixed with unsorted municipal waste. Your participation is an important part of the effort to minimize the impact of batteries and accumulators on the environment and on human health. For proper recycling you can return this product or the batteries or accumulators it contains to your supplier or to a designated collection point.
-
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.
-
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation. There are separate collection systems for used batteries and accumulators.
-
Please, dispose of batteries and accumulators correctly at your local community waste collection/recycling center.
-
Radio Equipment Directive
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of the Radio Equipment Directive 2014/53/EU.
-
Restriction of the use of certain hazardous substances (RoHS) Directive
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares the whole product including parts (cables, cords, and so on) meets the requirements of RoHS Directive 2011/65/EU and amendment Commission Delegated Directive (EU) 2015/863 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2.0”).
-
Machinery Directive
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of the Machinery Directive 2006/42/EC.
-
EU Authorised Representative:
-
Segway-Ninebot Europe
-
Dynamostraat 7, 1014 BN Amsterdam, The Netherlands.
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product model: P100SE complies with the essential requirements and other relevant provisions of
-
the Radio Equipment Directive 2014/53/EU, the machinery directive 2006/42/EC, and the RoHS Directive 2011/65/EU and amendment Commission
-
Delegated Directive (EU) 2015/863.
-
The declaration of conformity can be viewed at the following address: http://eu-en.segway.com/support-instructions
-
UK Compliance Statement
-
Radio Equipment Regulations 2017
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
-
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares the whole product including parts (cables, cords, and so on) meets the requirements of The Restriction of
-
the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
-
Supply of Machinery (Safety) Regulations 2008
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of The Safety of Supply of Machinery (Safety) Regulations 2008.
-
UK Authorised Representative:
-
UKCA Experts Ltd.
-
Dept 302, 43 Ostin Road Carrot, Don caster, DN6 8DA, United Kingdom
-
Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product model: P100SE complies with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017,Supply of Machinery (Safety) Regulations 2008 and the Restriction of the Use of Certain Hazardous Substances in
-
Electrical and Electronic Equipment Regulations 2012.
-
The declaration of conformity can be viewed at the following address: www.segway.com
Bluetooth | Frequency Band(s) | 2.4000–2.4835GHz |
---|---|---|
Max. RF Power | 20 mW |
Trademark
Segway and the Rider Design are the trademarks of Segway Inc.; Android is the
trademark of Google Inc., App Store is a service mark of Apple Inc. The
respective owners reserve the rights of their trademarks and copyrights, etc.
referred to in this manual.
We have attempted to include descriptions and instructions for all the
functions of the KickScooter at the time of printing. However, due to constant
improvement of product features and changes of design, your KickScooter may
differ slightly from the one shown in this document. Visit the Apple app Store
(iOS) or the Google Play Store (Android) to download and install the Segway-
Ninebot App. Please note that there are multiple Segway and Ninebot models
with different functions, and some of the functions mentioned herein may not
be applicable to your unit. The manufacturer reserves the right to change the
design and functionality of the KickScooter product and documentation without
prior notice.
(※The Segway-Ninebot App can support Kick Scooter with built-in Bluetooth)
© 2022 Ninebot (Beijing) Tech Co. Ltd. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>