Mossloo MSLM6044Q UV Sanitizer with Wireless Charger Instruction Manual

MSLM6044Q UV Sanitizer with Wireless Charger
Instruction Manual

|
---|---

Functions:

What’s included:

1 x UV Sanitizer with Wireless Charger
1 x USB-A to Type-C Cable
1 x instruction Manual

Tech Specifications:

• Type-C Input: DC 5V/2A
• Wireless Output: 5W

instructions:

1. Wireless Charging Function:
   • Connect the provided charging cable to a power source and to the Type-C port ④.
   • Once connected the LED Indicator will begin to GREEN.
   • Place wireless charging supported mobile device on the charging surface⑥, the LED Indicator doesn’t change.
   Note: When wireless charging, if the LED indicator flashes blue the device is either
   Note a wireless charging device or there is an object between the device and charging surface interfering with the charging process.

2. UV Sanitizing Function:
   • Press the Touch Button③ to turn on the UV lights. The LED indicator will flash RED when UV Sanitizing has started.
   • The UV lights will turn off themselves after 5mins, or press button③ to turn off UV lights. (There will be a ticking sound and the LED indicator turns GREEN once sanitizing is  done.)
   **DO NOT LIFT UP THE COVER⑤ ONCE THE SANITIZING PROCESS HAS STARTED: The UV LED will automatically shut off when you open the lid during sanitizing process.

SAFETY PRECAUTIONS:

WARNING- When using this product, basic precautions should always be followed:

1. Read all the instructions before use.
2. Never store or use this product in temperatures below 32°F(0°C) or above 115°F(45°C).
3. Do not overcharge your phone. The unit may become hot under excessive use Remove your phone once it is fully Never charge your phone for more than 7 hours at a time.
4. The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles.
5. To reduce the risk of injury, close supervision is required when the product is used near children.
6. Do not expose the device to moisture.
7. Do not use the device in excess of its output rating. Overload outputs above the rating may result in a risk of fire or injury
8. Do not use the device if damaged or
9. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
10. Do not disassemble the device. For repairs, seek a qualified service incorrect reassembly may result in a risk of fire or injury.
11. Do not expose the device to fire or excessive temperature. Exposure to fire or temperatures above 104°F may cause
12. Ensure that qualified service professionals use only identical replacement parts to ensure product safety.
13. Attachments on the back of your phone can impede the effectiveness of the wireless charger, and lead to overheating. Please remove any attachments from the phone before charging on this device.

FCC Information on
This device complies with Part 15 of the FCC Rules.
Caut on: Any changes or modifications not expressly approved could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
**EPA Est. NO.: 97922-CHN-1

MADE IN CHINA**

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>