Mossloo Industrial MSL-M1030Q Wireless Charger Instruction Manual
- June 5, 2024
- Mossloo Industrial
Table of Contents
Wireless Charger
Instruction Manual
MSL-M1030Q
Features:
- Charging Pad Surface
- LED Indicator
- Type-C Input Port
What’s included:
1 x Wireless Charging Pad
1 x USB to Type-C Cable
1 x Instruction Manual
Tech Specifications
- Input power: 5V/2A 9V/2A
- Output power: 5W/7.5W/10W/15W
INSTRUCTIONS:
- Charging Mobile Devices:
a. Ensure that your phone or tablet supports wireless charging. It will be listed in the manufacturer’s specifications. (See also the last page of this manual).
b. Connect the wireless charging pad to a USB adapter with the provided cable. Once connected LED Indicator will glow GREEN.
c. Place the enabled device on the surface of the wireless charging pad. The LED will turn RED to indicate that the phone is charging.
- Note: To charge devices, use only the accessory cable or the cable included with your own device by the manufacturer.
SAFETY PRECAUTIONS:
Read all the instructions before using the product.
- Do not use it on an aircraft or in a hospital.
- To reduce the risk of injury, close supervision is necessary when the product is used near children.
- Do not expose the device to any moisture.
- Do not use the device in excess of its output rating. Overloaded outputs above rating may result in a risk of fire or injury.
- Do not use the device if damaged or modified. The damaged or modified device may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
- Do not disassemble the device. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury.
- Do not expose the device to fire or excessive temperature. Exposure to extreme heat may cause an explosion.
- Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
- This device is not a toy.
- Do not overcharge your Phone. The unit may get hot with excessive use. Remove the Phone when it is fully charged. Never charge for more than 7 hours at a time.
- Attachments on the back of your phone can impede the effectiveness of the wireless charger, and lead to overheating. Please remove attachments from the phone before charging on this device.
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
KEEP OUT OF REACH OF CHILDREN
FC
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.