VIVO DESK-E-200B Black 2 Tier 55 Inch x 17 Inch Electric Desk Frame Controller Instruction Manual
- June 3, 2024
- Vivo
Table of Contents
Black 2 Tier 55″ x 17″ Electric Desk Frame Controller
Instruction Manual
DESK-E-200B Black 2 Tier 55 Inch x 17 Inch Electric Desk Frame
Controller
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual and do not exceed
weight capacity. We cannot be liable for damage or injury caused by an
improper mounting, incorrect assembly, or inappropriate use.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE, AND
ELECTRIC SHOCK, PLEASE READ THE FOLLOWING
INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN THE PRODUCT WHILE THE POWER IS CONNECTED.
- DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE THE DAMAGED PARTS.
- NEVER OPERATE THE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
OPERATING CONTROL PANEL
OPERATING INSTRUCTIONS: When the system is powered on, the existing
desktop height will appear on the control panel. Press and hold the up or down
arrow until the desk reaches the desired height.
Memory Mode
To store a certain height in the controller’s memory, first press “S”. The
controller display will begin flashing. Now press the sitting position or
standing position button within 6 seconds to store the current height in
memory. Once in memory, you can recall the sitting or standing height settings
by pressing the corresponding button. Touching any button will stop the
automatic adjustment.
Power-Saving Mode
When no actions are made for over 2 minutes, the system will enter power-
saving mode. Touch any button to enter operation mode.
Function Mode
Press and hold the “S” button for 3 seconds, or until “S – -” begins flashing
on the display. Press “S” again to enter Function mode. Within function mode,
use the up and down buttons to scroll through settings, and use the “S” button
to select options. If no action is taken for 20 seconds, the desk will return
to operating mode.
- Change Displayed Unit (Un): Press the up or down buttons until the display shows “Un”, and press “S” to select. Press up or down to select “SI” (metric) or “In” (imperial). Hold “S” for 2 seconds to save the setting.
- Change Brightness (br): Press the up or down buttons until the display shows “br”, and press “S” to select. Press up or down to select Low (L), Normal (n) or High (H) brightness. Hold “S” for 2 seconds to save the setting.
- Collision Force Detection (CF): Press the up or down buttons until the display shows “CF”, and press “S” to select. Press up or down to select “OFF”, Low (L), Normal (n) or Heavy (H) collision force detection. Hold “S” for 2 seconds to save the setting.
Reset Mode
While the unit is powered on, press the down arrow until the desk moves to the
fully lowered position. Press and hold the down arrow for 5 seconds or until
“rES” is displayed to enter reset mode. Continue holding the down arrow, and
the desk will move down to the lowest possible height and then move back up
slightly. The desk will then return to operating mode.
TROUBLESHOOTING
Error Code Description/Resolution
HOT Heat Warning: Allow the desk to rest for 18 minutes.
E10 Motor connection fault: Disconnect desk power, disconnect the motor,
reconnect the motor, then reconnect power.
E20 Desk overload: If overloaded while moving up, an error will clear
after 3 seconds. If the overloaded move down, unplug the desk for 10 seconds
then reconnect the power.
E02 Obstacle protection. The desk will automatically move back 4cm after
the collision.
E31 Under-voltage (power brownout). Will clear automatically when line
power is corrected.
E32 Over-voltage (power surge). Will clear automatically when line power
is corrected.
NOTES
- Circuit Protection: If the motor or controller becomes disconnected, the desk will cease operation. The error will clear after all components are reconnected.
- Self-protection function: The unit will enter a protective mode should the system operate continuously in excess of 2 minutes with “HOT” on the controller display. The system will return to normal operation after approximately 18 minutes.
- Do NOT remove or reconnect power to reset the unit when in a protective or “HOT” state, as this may damage the electronics.
Love your new VIVO setup and want to share?
Tag us in your photo!@vivo_us
LAST UPDATED: 09/23/2021
REV1
Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can
offer immediate assistance with rapid response times. If any parts are
received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
AVG. RESOLUTION TIME (within office hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black 2 Tier 55" x 28" Electric Desk with Push Button Memory Controlle – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>