kogan CTJMPSTW16B 16000mAh Water Resistant Portable Jump Starter User Guide

CTJMPSTW16B 16000mAh Water Resistant Portable Jump Starter
User Guide

SAFETY & WARNINGS

• Use only the included battery clamp to start the car.
• Do not use this unit if any part of the cable, clamp or cord is damaged.
• Never connect both clamps together when the product is turned ON.
• Do not connect both cable clamps to the same piece of metal, or the jump starter will be damaged.

COMPONENTS LIST

• 1 x 16000mAh Jump Starter
• 1 x Smart Battery Clamp
• 1 x USB-C to USB-A Cable
• 1 x USB-C to USB-C Cable
• 1 x User Guide
• 1 x Carry Pouch

OVERVIEW

1| On/Off Button (Multifunctional)| Press the button to charge your devices. Press the button to see the remaining capacity. Long press the button to turn the flashlight on or off.
---|---|---
2| Charging Indicator Lights| Shows the charging progress: 25%, 50%, 75% and 100%.
3| LED Flashlight| Flashlight modes: Solid, SOS, Flash and Off
4| USB-A Output Port 1 (QC 3.0)| Charge QC 3.0 compatible devices.
5| USB-A Output Port 2 (QC 3.0)| Charge QC 3.0 compatible devices.
6| USB-C Input/Output (PD3OW)| Charge the jump starter via USB-A to USB-C cable. Charge PD3OW compatible devices via USB-C to USB-C cable.
7| Micro USB Input Port| Charge the jump starter via the Micro USB cable.
8| Jump-Starting Port| Insert the plug into the jump-starting port.
9| Black Clamp| Connect the black clamp to the negative terminal of the car battery.
10| Red Clamp| Connect the red clamp to the positive terminal of the car battery.
11| Plug| To be inserted into the jump-starting port for use.
12| Battery Clamp Indicator Lights| Show the status of the smart battery clamp.
13| Force Start Button| Press this button if the car battery voltage is too low.

OPERATION

Charging the product

1. Connect the jump starter and the power source via the USB-C cable or Micro USB cable.
2. Short press the on/off button to turn on the product. While charging the jump starter, the battery level indicator light will flash. Once it is fully charged, all 4 battery level indicator lights will be on.
3. Unplug the cable when no charge is required.

Note:

• When using the product for the first time, make sure that the jump starter is fully charged.
• A wall adapter is not included in the package.

Power bank

1. Connect the product and the device to be charged via a USB cable.
2. Press the on/off button to turn on the product.
3. Unplug the cable when no charge is required.

LED flashlight
Long press the on/off button for 3 seconds to turn on the light. Short press the on/off button to switch modes among Solid, SOS and Flash. Long press the on/off button for 3 seconds to turn off the light.
Jumpstart your car
Note: 

• This product is for 12V car (all petrol or up to 6.0L diesel engines) only.
  ‘Ensure that 3 to 4 indicator lights are illuminated (battery level is above 50%) before you use it to jump-start your car.

Step 1 : Insert the plug of the smart battery clamp completely into the jump starter. If the green and red-light indicators on the battery clamp are flashing alternately, you are safe to move on to the next step.

Step 2: Connect the red clamp to the positive terminal (+) of the car battery and connect the black clamp to the negative terminal (-) of the car battery. If the green and red-light indicators on the battery clamp are flashing alternately, you are safe to move on to the next step.
However, if the red indicator light is on:

• The battery clamp may be connected in reverse. If so, disconnect the battery clamp from the vehicle and the jump starter.
• Adjust the clamps for maximum contact with battery terminals.

Step 3-a: Start the car as normal.

• If the car fails to start, disconnect the battery clamp from the vehicle and the jump starter. Wait for at least 30 seconds before trying again.
• If the car still fails to start after 3 attempts, use the force start function as per step 3b.

Step 3-b (optional): Force starts function.

• Make sure that the clamps are connected to the correct polarity battery terminal.
• Hold the force start button for 3 seconds to enable the force start function.
• When the indicator light of the smart clamp is solid green, the vehicle will need to be started within 30s.

Step 4: Once your car is started, remove the battery clamp from the car battery and the jump starter within 30 seconds.

o Check the orientation of the clamps on the battery terminals
2. The clamp is short-circuited:
a Check whether the clamps are contacting one another or are connected to the same piece of metal.
3. Reverse charging protection: the voltage of the car the battery is higher than 12.6V:
o No jump-starting is needed to start the car.
Rapidly flashing red| The temperature of the clamp exceeds 65 (+/-5) degrees.
Remove the clamp until the lights flash red and green.
Slowly flashing green| The voltage of the jump starter is too low. Charge the jump starter

CARE & MAINTENANCE

• Never use the product to start a bulging or damaged car battery.
• Store the product in a shaded, well-ventilated area.
• Handle the product with care. Avoid dropping or striking the product heavily and repeatedly.
• Do not attempt to disassemble or modify the product.
• Do not use detergents to clean the product.
• Do not place or use the product in a high-temperature environment for an extended period. The operating temperature of this product is -20-60° C. The storage temperature of the product should not exceed 50°C.
• Check the battery level of the product at least once every three months and charge the product in time.
• Keep the product away from children and pets.

SPECIFICATIONS

QC18W: 5V/3A, 9V/2A, 12V/1.5A
USB-A outputs| 5V/3A, 9V/2A, 12V/1.5A
Note: When using x2 USB outputs (x2 USB-A, or x1 USB-A and x1 USB-C) at the same time, the unit outputs voltage will reset to 5V.
Jump-start current| 600A (last for 1 second)
Peak current| 1200A (last for 0.2 second)
Short circuit protection| Effective
Over-discharge protection| 13v±0.3v
Overheating protection| > 65°C ± 5°C
Reverse polarity protection| Effective
Reverse charging protection| (12.6v±0.3v)
Dimensions (L x W x H)| 185 x 100 x 45mm

FAQ

Q: How is the product turned off?
A: This product will power off automatically when no load is detected or when charging is complete.
Q: How long does it take to fully charge the jump starter?
A: Approximately 3-9 hours through the Micro USB input port or USB-C input port.
Q: How many times can this product start a vehicle at full capacity?
A: Approximately 20 times.
Q: How many times can this product fully charge a mobile phone?
A: This will depend largely on the battery capacity of the mobile phone being used. For example, an iPhone 8 can be fully charged ~4-5 times.

Need more information?
We hope that this user guide has given you the assistance needed for a simple setup.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>