VIVO DESK-V100EWY Controller Instruction Manual

VIVO DESK-V100EWY Controller

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.

Instruction Manual: https://vivo-us.com/products/desk-v100eby

WARNING

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

ELECTRICAL SAFETY INSTRUCTIONS

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.

OPERATING CONTROL PANEL

OPERATING INSTRUCTIONS

When the system is powered on, you will hear a beep and the existing desktop height will be displayed on the control panel.

Upward and Downward Movement: Press and hold the up or down arrow until the desk reaches the desired height.

Memory Mode

To store a certain height in the controller’s memory, first press “M”. The letter “S-” will be displayed. Now press “1”, “2” or “3” to store the current height in memory. Each number can store a different height. Once in memory, you can recall any of the three height settings by pressing the corresponding button.

Timed Reminder Mode

To set the timer, press “A”. The display will flash “00” representing 0 minutes, and the screen will begin flashing after 2 seconds. Now press the up or down arrows to adjust the time (the default setting is 45 minutes). Wait 5 seconds, and the set time will be saved and the countdown will begin. When the timer has reached the set time, the controller will beep for 10 seconds, reminding the user to adjust the working position. If no action is taken, the controller will beep again after 5 minutes. The timer will automatically turn off if no action is taken after the second reminder. To deactivate the timer, press and hold “A” for 3 seconds, and the display will show “OFF”.

Reset Mode

While the unit is powered on, press the down arrow until the desk moves to the fully lowered position. Restart the system by unplugging for at least 5 seconds and plug back in, then hold the down arrow until RST is displayed. Continue holding the down arrow and the desk will move to the lowest position, then raise slightly and stop to complete the reset process.

TROUBLESHOOTING

• If the displayed height no longer matches the actual height, reset the desk by following the “Reset Mode” directions.
• If the desk stops moving and the display shows “E01” or “E02”, allow the desk to rest for at least 18 minutes before attempting to operate again.
• If the desk is not operational, disconnect the power, motor and control panel from the control unit. After waiting for at least 10 seconds, reconnect the motor and panel to the control unit, then reconnect power.
• If RSR/RST appears, n error has occurred and entered reset mode for protection; complete reset process to clear error.

NOTES

• Self-protection function: The unit will enter a protective mode should the system operate in excess of 2 minutes. The system will return to normal operation after approximately 18 minutes.
• Over-current protection mode: While operating, should the load on the desk exceed rated specifications, the system will enter into over-current protection mode to protect the system from damage. When this happens, the desk will move downward slightly and come to a stop with the current height displayed.
• Do NOT remove or reconnect power to reset the unit when in a protective “E01” or “E02” state, as this may damage the electronics.

CAUTION

• Keep monitor and laptop base fully on the desktop.
• Follow the cable routing instructions to avoid the potential to pinch cables.
• Leave enough slack in cable to allow for full range of vertical motion (15” / 38 cm).
• Raise desktop slowly to keep items stable.

Failure to follow these instructions may result in property damage and/or personal injury.

Love your new VIVO setup and want to share?

• Tag us in your photo! @vivo_us
• Open Monday – Friday 7:00 am – 7:00 pm CST,
• 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
• www.vivo-us.com Chat live with an agent! AVG. RESOLUTION TIME (within office hrs): < 15 M
• help@vivo-us.com
• AVG. RESPONSE TIME (within office hrs): 1HR 8M
  • 23% within < 15m
  • 38% within < 30m
  • 61% within < 1hr
  • 83% within < 2hr
  • 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo- us.com

• GET IN TOUCH: Monday-Friday from 7:00 am-7:00 pm CST
• help@vivo-us.com
• www.vivo-us.com
• TEL: 309-278-5303
• Chat live with an agent!

our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>