PRINCESS AUTO 9001314 Low Profile Floor Jack Instruction Manual
- June 5, 2024
- PRINCESS AUTO
Table of Contents
PRINCESS AUTO 9001314 Low Profile Floor Jack
SPECIFICATIONS
Lift Capacity (ton) | 3 |
---|---|
Lift Capacity (lb) | 6,000 |
Min. Lift Height (in.) | 3-1/2 |
Max. Lift Height (in.) | 18 |
Saddle Size (in.) | 4-5/16 |
Handle Size (in.) | 39-3/8 |
Wheel Size (in.) | 2-3/8 |
Strokes to Full Height | 28 |
Material | Steel |
Finish | Powder coated |
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice is an alert that there is a possibility of property damage, injury or death if certain instructions are not followed.
DANGER!
- This notice indicates an immediate and specific hazard that will result in severe personal injury or death if the proper precautions are not taken.
- This notice indicates a specific hazard or unsafe practice that could result in severe personal injury or death if the proper precautions are not taken.
- This notice indicates a potentially hazardous situation that may result in minor or moderate injury if proper practices are not taken.
- This notice indicates that a specific hazard or unsafe practice will result in equipment or property damage, but not personal injury.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection,
and maintenance instructions.
WORK AREA
- Operate in a safe work environment. Keep your work area clean, well-lit and free of distractions. Place lights so you are not working in a shadow.
- Keep anyone not wearing the appropriate safety equipment away from the work area.
- Store unused tools properly in a safe and dry location to prevent rust or damage. Lock tools away and keep out of the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian Standards
Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
-
Always wear impact safety goggles that provide front and side protection for the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed. -
Wear gloves that provide protection based on the work materials or to reduce the effects of tool vibration.
-
Wear protective clothing designed for the work environment and tool.
-
Non-skid footwear is recommended to maintain footing and balance in the work environment.
-
Wear steel toe footwear or steel toe caps to prevent a foot injury from falling objects.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid personal injury or damage to tool.
- Do not operate any tool when tired or under the influence of drugs, alcohol or medications.
- Avoid wearing clothes or jewelry that can become entangled with the moving parts of a tool. Keep long hair covered or bound.
- Do not overreach when operating a tool. Proper footing and balance enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from repeated
use) replace strict adherence to the tool safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious personal injury.
-
Use the correct tool for the job. This tool was designed for a specific function. Do not modify or alter this tool or use it for an
unintended purpose. -
Do not use the tool if any parts are damage broken or misplaced. Repair or replace the parts.
-
Do not overload the jack beyond its rated load capacity (see Specifications).
-
Do not use a handle extension for the jack handle.
-
Rest the jack’s base on a firm, level surface capable of sustaining the load. The jack must be free to roll under the vehicle. Keep the surface clean and free from debris.
-
Make sure the saddle is fully positioned under the load
before operating. -
Make sure the load is stable, so it does not shift when lifting or lowering.
-
Make sure there is enough clearance around the jack and the load during lifting or lowering actions.
-
Before lifting a vehicle, apply the emergency brake and block all wheels.
-
Do not lift a vehicle while people are inside it.
-
Support the load with jack stands or a support structure of adequate capacity immediately after lifting. Never work under a load without additional support devices.
-
The jack must remain in a static position for lifting and lowering loads. Never move a load that is elevated on the jack. Ensure the load remains stable at all times.
-
Do not push a load off the jack; lower carefully.
-
Before lowering load, ensure that there are no obstructions underneath and that all people are standing clear.
-
Do not place your hands between the moving components.
-
Never allow load to tilt on the jack as the jack may kick out causing injury to the operator and/or cause the load to fall.
-
Inspect the tool before each use. DO NOT use if bent, broken, cracked, leaking or otherwise damaged, any suspect parts are noticed or it has been subjected to a shock load.
-
DO NOT use the jack if damaged or it was subjected to a dynamic shock load. This is a sudden and unexpected load or force applied to the jack. Have the jack inspected and repaired by a qualified service technician.
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic fluid under pressure
penetrates your skin. See Injection Injury precautions for instructions before
using a pressurized hydraulic system.
- Do not touch or handle hydraulic hoses or components while under pressure. Hydraulic fluid escaping under pressure has sufficient force to penetrate your clothing and skin. A pinpoint hole may inject hydraulic fluid into your body. Seek immediate medical attention if this occurs (see Injection Injury).
- Never exceed the hydraulic system’s load capacity (see Specifications).
- Do not adjust the hydraulic system’s relief setting. The settings are preset by the factory.
- Hydraulic oil under pressure is hot and can cause a burn injury if touched, sprayed or spilled. Allow the hydraulic system to cool before conducting maintenance.
- Hydraulic components require regular inspection. Release all pressure from the system before you inspect it. Replace damaged hydraulic parts with identical manufacturer’s components.
- Do not attempt makeshift repairs to a hydraulic system. Such repairs can fail suddenly and create a hazardous condition.
- Hydraulic fluid has a combustible flash point of 200°F (93°F). Do not expose the fluid to an ignition source.
- Change your clothing immediately if sprayed with hydraulic fluid. Store clothing or rags contaminated with hydraulic fluid in an approved metal safety can with a spring-closing lid and venting designed to contain a fire.
- Only use hydraulic fluid in the pump. Do not substitute or mix brake fluid, or any other fluid, with the hydraulic fluid. This can result in a pump failure and injure the user or bystander. It may also damage the pump.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment if fluid penetrates
your skin. It may feel like a pricking or sting. Do not wait for the
appearance of symptoms. A toxic reaction can occur from the exposure. Delay in
treatment can lead to amputation or death.
Inform the medical staff that you have a fluid penetration injury as soon as
you arrive at the medical facility. The severity of the symptoms will depend
on the type of fluid injected. Bring the Safety Data Sheet for the fluid with
you to the medical facility if possible.
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under
pressure from the tool has sufficient force to penetrate your clothing and
skin. Follow the precautions below to avoid an injection injury.
- Always check for leaks wearing a face shield, safety goggles, rubberized gloves and protective clothes.
- Release all pressure from the system before you inspect it.
- Do not use your hands to detect a fluid leak. Use a large piece of wood, cardboard or paper and watch for discolouration.
- Replace damaged parts with identical manufacturer’s components to ensure it is rated to handle the pressure.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the missing part before operating. Failure to do so could result in a malfunction and personal injury. Remove the parts and accessories from the packaging and inspect for damage. Make sure that all items in the parts list are included.
OPERATION
Numbered references in parenthesis (#1) refer to the included Parts List.
RAISING A LOAD
WARNING! Do not place any part of your body under the load without jack stands
in place. The floor jack is not designed to maintain heavy loads for long
periods of time
- Place the jack on a hard level surface capable of handling the load.
- Connect the front handle bar (#30) to the rear handle bar (#32) and secure using a hex head screw (#31). Insert the assembled handle into the fork’s (#24) socket and secure using the handle locking screw (#25)
- Twist the handle to the right to close the release valve.
- Pump to raise the ram. Stop just before the ram contacts the load’s lift point. Inspect the ram’s position and adjust if necessary.
- Pump slowly until the ram is supporting the load. Continue to pump as normal to lift the load to the desired height.
- Position supports like jack stands if the load will remain off the ground for an extended period. Consult the support device’s manual for proper placement.
LOWERING A LOAD
WARNING! Dynamic shock loads are created by quick opening and closing of the
release valve when lowering the load. The resulting overload may cause the
hydraulic system to failure, which could result in severe personal injury
and/or property damage. Before lowering the load or vehicle, ensure that there
are no obstructions underneath and that all people are standing clear.
- Open the valve by gradually twisting to the left.
- The load will begin to lower.
- Twist right to slow and left to increase the rate of descent.
- Remove the jack once the load is on the ground or a support mechanism like jack stands.
- The ram should fully retract. If it does not, push down on it until it is seated.
RAISING AND LOWERING A VEHICLE
Take these additional steps before following instructions in Raising a Load
and Lowering a Load.
- Set the vehicle in parking gear and engage the parking brake.
- For vehicles with a manual transmission, engage the parking brake and leave the car in reverse or 1st gear. Consult your vehicle owner’s manual for the correct gear.
- Place wheel chocks that fit the wheel curve on either side of the vehicle’s remaining wheels.
- Place the jack only on support points or areas specified by the vehicle manufacturer (consult owner’s manual).
- Lift the vehicle to a height that leaves enough room to place the jack stands.
- When the work is done, raise the load enough with the jack to carefully remove the jack stands.
- Slowly and carefully lower the load.
CARE & MAINTENANCE
WARNING! Do not loosen or remove the Safety Valve Cover Screws (I). The safety valve setting is preset. Changing the valve setting can cause a jack to fail, resulting a serious injury if the load falls.
-
Maintain the tool with care. A tool in good condition is efficient, easier to control and will have fewer problems.
-
Inspect the tool components periodically. Repair or replace damaged or worn components. Only use identical replacement parts
when servicing. -
Follow instructions for lubricating and changing accessories.
-
Keep the tool handles clean, dry and free from oil/grease at all times.
-
Maintain the tool’s labels and name plates. These carry important information. If unreadable or missing, contact Princess Auto Ltd. for replacements.
-
Have a qualified technician inspect the jack:
- Once a year.
- After receiving a shock load. Take the jack out of service until the technician certifies that it is safe to use.
WARNING! Only qualified service personnel should repair the tool. An improperly repaired tool may present a hazard to the user and/or others.
HYDRAULIC RAM MAINTENANCE
Monthly maintenance is recommended for the hydraulic ram. Any restrictions due
to dirt, rust, etc. can cause the either slow movement or extremely rapid
jerks, damaging the internal components. The following steps are designed to
keep the pump maintained and operational.
- Lubricate the cylinder and the pumping mechanism with light oil.
- Visually inspect for cracked welds, bent, loose, missing parts or hydraulic oil leaks.
- Check and maintain the ram oil level.
- Always store the hydraulic ram in the fully retracted position. This will help protect critical areas from corrosion.
- Do not use brake or transmission fluids or regular motor oil as they can damage the seals. Always purchase and use products labeled hydraulic jack oil.
- Remove any hydraulic pump from service that is damaged, worn down or operates abnormally, until repaired by an authorized service technician.
REPLACING THE HYDRAULIC JACK OIL
Replace the jack oil annually.
- Lower the ram and remove the oil filler plug.
- Lay the jack on its side and drain the oil into a suitable container. Dispose of used hydraulic oil in accordance with local by-laws.
- Stand the jack on its wheels and casters and wipe off any excess oil.
- Fill the cylinder with a high quality hydraulic jack oil, up to 1/4 in. below the oil plug opening.
- Follow the steps in Bleeding the Hydraulic System.
BLEEDING THE HYDRAULIC SYSTEM
Bleed excess air from the hydraulic system as follows:
- Remove the oil filler plug and fill the pump with hydraulic fluid to 1/4 in. below the opening.
- Wait 5 minutes for trapped air to rise to the surface.
- Open the release valve by turning the handle counterclockwise.
- Pump the handle for several full strokes to eliminate any air in the system.
- Check the oil filler hole and if necessary, top off with more hydraulic oil.
- Reinstall the oil filler plug.
- Close the release valve by turning clockwise.
- Test the ram several times for proper operation before putting it into use. Do not use the ram if it still does not appear to be working properly. Have a qualified service technician service or repair the hydraulic system.
FLUSHING THE VALVE
Contaminants may block the release valve, causing issues when attempting to
lower a load. Clear the valve with the following steps.
- Lower the saddle and securely close the release valve.
- Manually lift the saddle several inches.
- Open the release valve and force the saddle down as quickly as possible.
LUBRICATION
Inspect and lubricate the tool when required. Only use light oil to lubricate
the tool. Other lubricants may not be suitable and could damage the tool or
cause a malfunction during use.
STORAGE
Lower the ram to its lowest position. Apply a thin coat of lubricant to the
steel parts to avoid rust. Remove the lubricant before using the tool again.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility. Contact your
local municipality for a list of disposal facilities or by-laws for electronic
devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
HYDRAULIC FLUID
Do not drain hydraulic oil into the sewer system or dispose of in an
uncontrolled location. Hydraulic fluid may take more than a year to break down
in the environment and the ingredients may still be toxic. Contact your local
municipality for proper disposal instructions or locations.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function properly or parts are missing. If unable to do so, have a qualified technician service the tool.
Problem(s) | Possible Cause(s) | Suggested Solution(s) |
---|---|---|
Jack will not lift load. | 1. The release valve is not closed tightly. |
2. Overloaded the jack.
3. Air is trapped in the hydraulic system.
| 1. Close the release valve firmly.
2. Reduceload or use a jack with a greater lift capacity.
3. Bleed air from thesystem.
Jack will lift, but will not maintain pressure.| 1. Release valveis not closed tightly.
2. Overloaded the jack.
3. Hydraulic unit is malfunctioning.
| 1. Close the release valve firmly.
2. Reduceload or use a jack with a greater lift capacity.
3. a. Replace theseals.
b. Have service technician repair the jack.
Will not lower after loading.| 1. Reservoir is overfilled.
2. Linkages arebinding.
3. Contaminated release valve.
| 1. Drain oil to the proper level.
2. Clean and lubricate all moving parts.
3. See Care & Maintenance – Flushing the Valve
Poor lift
performance.
| 1. Hydraulic oil level is low.
2. Air is trapped in the hydraulic system.
| 1. Add oil to the proper level.
2. Bleed air from thesystem.
Will not lift to the max. height.| 1. Air is trapped in the system.
2. Hydraulic oil levelis too low.
| 1. Bleed air from thesystem.
2. Add oil to the proper level.
PARTS BREAKDOWN
PARTS LIST
# | DESCRIPTION | QTY |
---|---|---|
1 | Ø19, C-Ring | 2 |
2 | Front Wheel | 2 |
3 | Side Plate Assembly | 1 |
4 | Lifting Arm Assembly | 1 |
5 | Saddle | 1 |
6 | Lifting Arm Assembly | 1 |
7 | Ø25, C-Ring | 4 |
8 | M6 Oil Nozzle | 1 |
18 | Rear Caster Assembly | 2 |
--- | --- | --- |
19 | M12, Thick Nut | 4 |
20 | Ø16, Spring Washer | 4 |
21 | M12x25, Hex Socket Head | 2 |
22 | Tie Rod | 1 |
23 | Handle Fork Fixing Bolt | 1 |
24 | Handle Fork | 1 |
25 | M12, Handle Locking Screw | 1 |
26 | Gear Shaft | 1 |
--- | --- | --- |
27 | Gear | 1 |
28 | Ø10, Spring Washer | 1 |
29 | M10, Nut | 1 |
30 | Front Handle Bar | 1 |
31 | M6x35, Hex Head Screw | 1 |
32 | Rear Handle Bar | 1 |
33 | Handle Grip | 1 |
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>