Shenzhen Yanshen Electronic EH301 125KHz RFID Desk Top USB Reader User Manual

: June 5, 2024
: Shenzhen Yanshen Electronic

Table of Contents

Feature:
How to use
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Yanshen Electronic EH301 125KHz RFID Desk Top USB Reader
User Manual

125KHz RFID DeskTop USB READER
Please read the user manual carefully before using the device

EH301 is an external input device that can read EM4100 and HID 125K proximity cards ID and output it to a computer or Android/iOS device via USB interface according to the specified format.

Feature:

a) Support Card list: HID 125KHz Proximity Card: ProxCardll(1326), ISOProx11(1386) , DuoProxll(1336), ProxKey111(1346) , ProxKey III (1346) , MicroProx Tag (1391) AWID Low-frequency Card: 26-50bits format card, Prox Wafer Disc, Clam Shell Card, Key Tag Casi /GE ProxLite 125KHz proximity (not all format) ; EM4100 or EM compatible
b) Output data at the cursor location, HID USB interface, Driver-free, Supports Android & iOS devices.
c) 44 output formats for both EM & HID, raw Wiegand data for HID 125K proximity cards only
d) Turn on/off buzzer sound, configurable as QWERTY (USA) / AZERTY (Europe) keyboard layout
e) Default setting: 10 digit format, With entering, buzzer sound, QWERTY keyboard, Disable HID Raw

How to use

Works with PC : Connect the reader to the USB port, Green LED light, then Green LED off and reader beeps & blue led light; Run text editable program (Word, Notepad. etc.), Read the card, the card number is shown on the window at the cursor location.
Works with Mac: same as work on PC, (Mac needs type C /Lighting to USB adapter)
Works with android device : an OTG adapter is required

Configuration of the reader
EH301 allows users to select the output format, (including “with or without Enter” “reverse data”), Turn-ON/OFF buzzer, enable/disable HID raw data, USA/Europe keyboard layout.
Config process is done through a 3-level menu system: Reader sends option text to screen, the user uses two different read config card methods to tell the reader to select or skip this option. if the choice “skip”, the reader will go to the next option at the same level, if choose “yes”, the reader will save it and then jump to a new option group. These 2 read config card methods are:
*Short read card:* read config card, reader sounds 1 beep (Bi), remove the card immediately
Long read card : read config card, reader sounds 1 beep (Bi), don’t remove the card, until reader sounds other 2 beeps (Bi-Bi), then remove the card
-3.1 Select reader output format 1 to 11
a) Run text editable program (suggest Excel); Plugin reader to PC till reader beeps (BLUE LED on)
b) Read the config card, the reader enters config mode (Green LED on) and start to send instruction menu on the screen, then the first format menu “18H- 10D” is shown, waiting for user choice
c) “Long read card” will let the reader save this format, and jump to the next group menu if want not this format, use “short read card”, then the next format will appear on screen
d) if skip all formats from 1 to 11, the reader will keep the previous output format setting
-3.2 Set reader parameters
** After formats 1-11, 5 parameters can be selected, menu as below:

12| with entering| Short read card= with entering| Long read card=without enter
---|---|---|---
13| buzzer sound| Short read card=buzzer sound| Long read card=disable buzzer
14| enable hid raw| Short read card=disable hid raw| Long read card=enable hid raw
15| reverse data| – Short read card=normal data| Long read card=reverse data
16| keyboard layout| Short read card=USA keyboard| Long read card=Europe keyboard

With entering -Send “Enter” after the card number ;
Without entering Only send card number Normal: card number in the normal sequence;
Reverse data: card number in the reverse sequence;
Buzzer sound: reader sounds “Bi” after reading card;
Disable buzzer: the reader is mute after reading the card
Disable HID raw : EM/HID/AWID card data are sent as format 1-11 which is selected before;
Enable HID raw: EM card follow format setting 1-11, but HID/AWID card data is sent as raw Wiegand data stream(See detail for hid raw data explanation in next page) -3.3 Quit Config mode: ( there are two ways to quit config mode) – power off the reader to quit at any time. This will not affect the already saved setting of each step – quit from the operation menu as below: (short read card can start config process again)
Repeat or quit config short read card = repeat long read card = quit
Notice::
a) After power on, if the other card is read before reading the config card, the reader will enter normal work mode. In normal work mode, blue LED is on. Config card will be read as normal card
b) HID raw data format is for user who has better knowledge on RFID card and Wiegand protocol, If it is enabled, Reader send 6 or 8 Byte HEX data when HID card is read according to below rule: The First 1 byte is card data bit length, others are card number data.
Example, reader sends “1A002468AC”, means:
Card is Wiegand 26 bit data : 1A (HEX) = 26 (DEC),
002468AC (HEX) =0000 00 00 0010 0100 0110 1000 1010 1100 (BIN)
Take 26 bits data from LSB to MSB(see above), according to Wiegand26 protocol, the finial data is 0 0001 0010 0011 0100 0101 0110 0”in Hex It is 123456, group as FC and ID, it is FC= 12 (HEX) or 18 (DEC)’ ID=3456 (HEX) or 13398 (DEC)
c) Normal formats 1-11 are listed as the table below:

Number/ Mark	Description	Data example
1 8h-10d	10 digits decimal	281845676
2 2h-3d 4h-5d	3 digits FC,5 digits ID	20440876 ( FC=204 ID=40876) /WG26

4. Advanced config (add prefix/suffix in output data or select client format for HID card ) If reader output data format “1-11” does not match with HID card number printing, the user may try HID card client definition format, EH301 has 22 client format options for choice. 4.1 Enter Advanced Config
4.1.1 Run text editable PC program (Excel, Note, etc. / Suggest Excel ); Plugin reader to PC;
4.1.2 Read config card and don’t move config card when reader sound the first “Br; till reader sound, 2nd “Bi”, remove the config card to start advanced config process.
4.2 Choice client format. The first menu display on the window is:

4.3 Set prefix and suffix
Prefix/Suffix can be any symbol/letter/number on the keyboard, They are divided into 6 groups. Users need to choose group first, then choose one character from this:rou Group list as:

! @ # $ % ^ & * ( )| _ + { } | | : ” ~ < > ?| – = [ ] \ \ ; ‘ ` , . /
---|---|---
A B C . . . . X Y Z| a b c . . . x y z| 1 2 3 4 5 6 7 8 9 0

Prefix and suffix can be enabled together or only one of the\
5. Other HID products online :
HID Card programmer ASIN:B07TMNZPXK ; HID Card/Fob ASIN:B07QXLH7L3 / B07QXLHKDP
Download operation video & documents & question-answer at www.said.cn/eh301
★Pls. send an email to check a solution for your problem before asking goods return, we will solve your Problems to reduce the unnecessary return ★
Support Email: Taylor@szjat.com.cn

Application picture

Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to rovide Reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by Shenzhen YanShen Electronic Co., Ltd may void the FCC authorization to operate this device. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
RF exposure statement: The device compliance RF exposure requirement and can be installed and used without restriction