PRINCESS AUTO 8829731 48-Inch Portable Lumber Mill User Manual
- June 6, 2024
- PRINCESS AUTO
Table of Contents
PRINCESS AUTO 8829731 48-Inch Portable Lumber Mill
SPECIFICATIONS
| Size | 48 in. |
|---|---|
| Fits | Chainsaw bars 24 to 48 in. |
| Thickness | Cuts planks from 0.20 to 11.81 in. thick |
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or
death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will result in severe personal injury or death if the proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that could result in severe personal injury or death if the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may result in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will result in equipment or property damage, but not personal injury.
WORK AREA
CAUTION! Do not assemble this Portable Lumber Mill until you have read this manual and have developed a thorough understanding of how the Portable Lumber Millworks.
WARNING! The warnings cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator.
- Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents.
- Keep children and bystanders away while assembling the Lumber Mill
- Be alert of your surroundings. Using the Lumber Mill in confined work areas may put you dangerously close to cutting tools and rotating parts.
ASSEMBLY
-
Insert two M8×75 bolts (#11) through the adjustment post (#12) and into the clamp bracket (#13). Ensure that the side of the adjustment post with measurements on it is facing away from you when assembling. Tighten the nuts at the bottom of the clamp bracket, but leave an adequate gap for the chainsaw bar.
-
Insert two M8×75 bolts (#11) through the adjustment post (#22). Slide the bolts through the nose guard (#14) and into the clamp bracket (#20). Tighten the nuts at the bottom of the clamp bracket, but leave an adequate gap for the chainsaw bar.
-
Attach the thrust end and post assembly to the end bracket using a U-clamp (#4) post clamp (#5) two flat washers (#7) and coupling nuts (#15).
-
Align the thrust end flush with the end bracket, and then secure the handle using M5x45 screws (#1) and lock nuts (#3).
-
Repeat steps 3 and 4 for the nose end but do not fully tighten the connections.
-
Attach the tie bar (#17) to the guide bar (# 19) using M8x25 bolts (#9) ,flat washers (#7), an M8 hex nut (#6) and a coupling nut (#15). Attach the tie and guide bar assembly to the thickness rails (#10) using 2 M8x25 bolts (#9), flat washers (#7) and coupling nuts (#15). Attach the shield (#25) to the thickness rails (#10) using 4 M8x25 bolts (#9), flat washers (#7) and coupling nuts (#15).
- Attach an end bracket (#8) to the thickness rails (#10) using 2 M8x25 bolts(#9), flat washers (#7) and M8 hex nuts (#6). Tighten the hex nuts using fingers only. Repeat the process for the second end bracket. Ensure the end brackets are flush with the thickness rails.
PARTS LIST
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>