COOYES COSU001 Stand UP Paddle Board User Manual

COOYES COSU001 Stand UP Paddle Board

Important Safety Guidelines

• Check weather conditions, forecasts and tides for your start point, route and destination.
• Consult any locals for safety tips whenever you are at a new spot.
• Avoid paddling in offshore winds.Try and paddle upwind/stream first.
• Be aware of the effect tides and currents can have on your journey.
• Avoid paddling alone. If not possible, ensure someone knows where you are going, and when you plan to be back.
• Take a method of contacting someone should you need help – eg a mobile phone in a dry bag.
• Do not use if you are under the influence of alchohol, drugs or medications.
• Always wear a buoyancy aid, even if you are a strong swimmer. Swallow your pride and be honest with your abilities.
• Dress appropriately for the weather and the water conditions. Either a wetsuit or boardshorts/bikini depending on the water temperature.
• Always wear a leash. This prevents you and your board from becoming seperated should you fall in.
• Never exceed the weight capacity limitations of your board.
• These inflatable boards are not designed to be pulled behind a boat.
• Inflate and deflate only with a compatible pump and never overinflate your board.
• Be honest about your skills. Only paddle in conditions and locations that are suitable for your ability.
• Regularly inspect your kit and follow our maintenance guidelines.

Introdution

1. Stand Up Paddle Board
2. a. Secure Bungee Tie-Downs
3. b. Non-Slip Deck Pad
4. c. Comfort Grip Handle
5. d. Air Valve
6.  Adjustable Paddle.
7. Portable Backpack.
8. Manual Air Pump.
9. Ankle Leash.
10. Large Fin.
11. Waterproof Cell Phone Pock..

Get the Best From Your Pump

While your pump may appear very straightforward at a glance, there are a few common misconceptions here that can cause confusion and result in ineffective inflation of your board. Please read this section to understand how to use your pump properly.

Setting up the Pump

1. Combine the pump body with the hose and turn to lock.
2. To inflate your board, attach the hose to the pump by screwing the fitment clockwise onto the air outlet Labelled Out . Make sure the hose is screwed on tightly so no air can escape. To defalte, screw the hose onto the air inlet Labelled In.

Single Action / Double Action Settings

Choose between single and double action settings on your pump by safely pulling the knob out or inserting it. Single action only pumps air out when you push down on the handles. Double action pumps air out on, both the up- stroke and the down-stroke. This is effectively twice as fast, but also more difficult. Try both settings and choose the one that works for you.

Single Action

Double Action

Double Action setting is only suitable for inflation at low pressures. You can use the Double Action setting at first and switch back to single action when pumping becomes too difficult.

Inflating the sup board

Unfold your board and remove the cap  on your air valve by twisting it in an anticlockwise direction. This will expose the inner mechanism of your valve.

Check that the central valve button is in the ‘Up’ position to ensure the valve is closed. This allows air to be pumped in, but not to escape again.

Start pumping. Keep your back straight and bend your legs with each pump stroke to use your body weight. Find a slow and steady rhythm that you can maintain. As you inflate your board, keep an eye on the pressure gauge mounted on top of your pump. Stop pumping when you have achieved 12 – 15psi of pressure.

Remove the pump hose and reattach the valve cap in its place to keep the inside of the valve clean and dry. Your board is now inflated and ready to ride.

Tightening your air valve

Due to the design of your board, the two-way air valve can work its way loose during delivery. It is important to check that your valve is completely tightened before use.
This should also be done periodically to make sure that it remains tight over time. This will prevent minor losses in pressure and will ensure the optimum performance of your board. Your valve consists of 2 main parts – The internal (bottom) section and the external (top section). If when inflated the valve leaks air around the edges,
this is because there is not an airtight seal between the PVC fabric of your board and the two sections of the valve. To stop the air leaking, you will need to tighten your valve down solidly by screwing the top section into the bottom section to create an airtight seal. Your air valve can only be tightened when the board is deflated.

1. Remove the valve cap on the top of the board, and insert the wrench supplied with your repair kit into the valve so it fits tightly.
2. Use your free hand to apply pressure to the valve, pressing the bottom section against the floor to hold it firmly in place.
3. Maintaining downward pressure on the tool and valve, firmly twist the wrench clockwise until the valve is completely tightened.

Attaching fins and leash

Slide the base of the fin firmly into the finbox with the fin tip pointing back towards the tail end of the board. This slot can be quite tight as it is designed to hold the fin firmly. Make sure the small hole in the base of the fin lines up evenly with the groove in the fin box. Insert the fin clip into the slot and push it through until it locks in place. You should hear a little click when the locking clip is firmly secured in place. Your fin is now properly attached and will not come out of place until you remove the locking clip.

groove in the fin box. Insert the fin clip into the slot and push it through until it locks in place.  You should hear a little click when the locking clip is firmly secured in place. Your fin is now properly attached and will not come out of place until you remove the locking clip.

Assembling your paddle

Your 3 Paddle Components

Blade

Midshaft

Shaft Extension

Set 1

Connect your blade to your midshaft by pushing in the silver button and slotting the blade into the midshaft so it clicks into place.

Set 2

Open the clasp on your midshaft and insert the shaft extension. Close the clasp to secure the shaft extension in place.

Tightening Your Clasp

Your shaft extension should be held securely by the clasp on the midshaft so that you get the best performance from your paddle. You will need to adjust your buckle by rotating it to get a tight fit.

Unlock

Rotate

Lock

Setting the Length of Your Paddle

Your paddle is as important as your board; Helping transfer the power from your stroke into a forward motion. For long distance paddling, a longer paddle shaft length gives longer lighter strokes that can propel you further with minimal effort. For surfing and racing, a shorter paddle shaft length gives quicker, sharper strokes. Open the clasp to adjust the length of the paddle for your personal preference or riding style. If unsure, our guidelines are to extend your paddle so that it is 6 inches longer than your height. Be careful as over extending your paddle places greater forces on the clasp and can cause damage. Our paddles are marked ‘O’ to indicate the maximum length for the shaft extension.

Patch repairing your board

1. You will find patches in your repair kit. Use a sharp pair of scissors to cut out a patch that can overlap the tear by approximately 1 inch on all sides.
2. Tape off the area and apply a thin layer of glue to evenly cover the area that will be patched. Apply 2 coats, waiting approximately 3 minutes between each.
3. Apply 2 layers of glue in the same way to the back of the patch that will be stuck down. Tip: use a brush, squeegee, or your finger to spread the glue evenly.
4. Remove the masking tape and ensure that the placement of your patch is correct as the patch will stick straight away. Roll the patch down, starting from one corner to avoid air bubbles.
5. For the glue to bond the patch firmly to the board, weigh down the repair with at least 10kg of weight and leave it for 24 hours so the glue can cure fully.
6. When the patch has stuck fully, apply a thin bead of glue around the edges to ensure it is fully sealed. Leave this glue for a further 24 hours before you reinflate your board.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>