Wuyi Zhifeng Arts Crafts 001 HD Smart Life Camera User Guide
- June 5, 2024
- Wuyi Zhifeng Arts Crafts
Table of Contents
Wuyi Zhifeng Arts Crafts 001 HD Smart Life Camera Mobile App Installation
Download and install 365Cam, 10S is downloaded from Apple Store, Android
system is searched in GooglePlay. To facilitate the installation, please scan
the QR code below to download 365Cam.
If your device cannot connect to GooglePlay, please scan the APK QR code below
to download and install.
Note: It is recommended to use the browser’s own or third-party QR code
scanning software to scan and download the App, WeChat sweep function does not
support the direct download and installation of App files.
(Note: All permissions must be opened when downloading the app)
Product button and indicator description
- ON/OFF: [ON key, press the button to tum on; press and hold to turn off after turning on)
- MODE: Press and hold for 5 seconds to restore the factory settings and disconnect the network connected to the monitor
- Charging indicator (blue) : Long light when charging, off when full
- Work indicator (red): BlinkingAong light is on state
Network indicator (red):
- slow flash, ap hotspot mode,
- long light, the device is successfully connected to wifi
- Fast flashing, device connection failed, wifi password input error
Note: When the camera working state is unknown, please reset the camera to restore factory settings (press and hold the camera reset button for more than 5 seconds), the camera reboot after opening the AP mode, wif indicator slow flash (3 seconds flash once).
- Click”+” to add a device. Click “Device AP Netvvork Configuration”
- Click “Go to WiFi Configuration” to jump to the WIFI connection page and select (“DGo•• .. x”, “DBG’ .. “‘, “HTM• .. •x•” ,”TUT …. “) WIFI hotspot and connect
- After the connection is successful, return to the App, and the device is added successfully. (If the APP does not automatically add the device, you can click Search to add the searched device)
The second connection method
- Click”+” to add a device. Click “Device AP Network Configuration”.
- Select Wi Fi and enter the password, click “Next” and th en click ” Go to WiFi Configuration”
- Jump to the WIFI connection page and select (“DGo•·••x”, 11DBG·•·•11, “HTM•·••x”‘, “TUT”'”‘ of the WIFI hotspot and connect. Return to the App after successful connection, the device is added successfully. (If the APP does not add the device automatically, you can click Searchto add the searched device)
Common problem
- When using this product for the first time, please fully cha
- Remote monitoring is not smooth. Please choose the suitable clarity according to the netvvork environment at that time.
- The memory card does not save video, and it must be formatted the first time the memory card is used.
- The default password of the camera is 6666. If you forget the user name or password, you can restore the camera to factory settings to get the default user name and password.
- The camera is restored to its factory settings. Press the reset button of the camera for about 5 seconds until the camera restarts.
- Why is the image blurry? Remove the protective film of the lens. If it is still not clear, please rotate the camera lens and focus. After focusing, a clear image can be obtained.
- APP can’t search to detect camera/can’t configure netvvork, please make sure the device is connected properly and check App Use permission is not restricted.
If the application always shows failure, try checking the following items:
- It supports ordinary routers, and public routes that require login page authentication are temporarily not supported.
- ‘\Mien configuring, note that the netvvork name, netvvork password and UID are not incorrect.
- Chinese V\lifi names and passwords and special symbols are not supported at the moment.
- Wfi signal that does not support 5G
- The device is not online and the red light is always on, indicating that the camera is connected to the network successfully, probably because the App permissions are not open. Please check whether to open.
- lfV\liFi is WEP encryption mode, please change it to WPA mode.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body.