Neomounts DS75S-950WH2 Monitor Mount Stand Instruction Manual

Neomounts DS75S-950WH2 Monitor Mount Stand

Product Information

• Product Name: DS75S-950WH2
• Manufacturer: NEOMOUNTS
• Measuring Unit: mm
• Weight Capacity: 1-8 kg
• Compatible VESA Sizes: 75×75, 100×100 mm
• Desk Thickness Compatibility: 10-50 mm (clamp), 10-55 mm (grommet)

Parts Included:

• A. (x1)
• B. (x1)
• C. (x1)
• D. (x1)
• E. (x2)
• F. (x8)
• G. (x1)
• H. (x1)
• I. (x1)
• J. M8x150 (x1)
• K. 4mm-3mm (x1)
• L. 6mm (x1)
• M. D6 (x3) Steel Spacer
• N. D6 (x3) Plastic Spacer
• O. M6x12 (x3)
• M-A. M4x12 (x8)
• M-B. M5x12 (x8)
• M-C. D5 (x8)

Product Usage Instructions

• Step 1: Clamp Installation
  Install the clamp to the desk – for desktop thickness between 10-50 mm

• Step 1: Grommet Installation
  Install the grommet through the desk – for desktop thickness between 10-55 mm

• Step 2: Attaching Upper Arm to Lower Arm
  Attach the upper arm to the lower arm

• Step 3: Attaching Crossbar
  Attach the crossbar

• Step 4: Unscrewing
  Unscrew using one rotation. Do not unscrew too far

• Step 5: Monitor Installation
  Install the monitors

• Step 6: Cable Management
  Remove the cable cover and run the cable(s) through the cover

• Step 7: Tightening the Screw
  Note: If the display does not stop at your desired position, tighten the screw as shown.
  

• Step 8: Horizontal Alignment
  For correct horizontal alignment, position the screens in the exact middle of the crossbar and place the monitor arm to the left side

Dimension And Tools

PARTS

Installation

STEP 1

A Clamp
Install the clamp to the desk – for desktop thickness between 10-50 mm.

B Grommet
Install the grommet through the desk – for desktop thickness between 10-55 mm

STEP 2
Choose the desired rotation mode (full range or 180° lock) and attach the arm to the base.

STEP 3
Attach the upper arm to the lower arm

STEP 4
Attach the crossbar

STEP 5
Attach the handle

• Unscrew using one rotation.
• Do not unscrew too far

STEP 6
Attach the VESA plate to the screen

STEP 7
Place the decorative covers

STEP 8
Install the monitors

STEP 9
Adjust the gas spring

STEP 10
Remove the cable cover and run the cable(s) through the cover

STEP 11
Adjust the mount to the desired position

STEP 12
For correct horizontal alignment, position the screens in the exact middle of the crossbar and place the monitor arm to the left side

SAFETY CAUTION

1. To ensure safety, please read this manual carefully before installation and follow the instructions. Store this manual in a secure place for future reference.
2. The manufacturer shall not be legally responsible for any equipment damage or personal injury caused by incorrect installation or operation other than that covered in this manual.
3. The mount is designed for easy installation and removal. The manufacturer shall not be liable for damage to equipment or personal injuries arising out of human factors or acts of nature, such as earthquake or typhoon.
4. It is recommended that the mount be installed by qualified personnel only.
5. At least two persons are needed to install or remove the product to avoid hazard of falling objects.
6. Please carefully inspect the area where the mount is to be installed:
   • Avoid places that are subject to high temperatures, humidity or contact with water.
   • Do not install the product near air conditioning vents or areas with excess dust and fumes.
   • Only install on vertical walls and avoid slanted surfaces.
   • Do not install in places subject to any shock or vibration.
   • Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when viewing the display panel.
7. Maintain sufficient space around the display to ensure adequate ventilation.
8. To ensure safe installation, first check the structure of the wall, ceiling or floor and select a secure mounting location.
9. The wall, ceiling or floor should be strong enough to sustain a weight of at least four times of the display and mount combined. The mounting location must be able to withstand earhquake or other strong shock.
10. Do not modify any accessories or use broken parts. Contact your dealer with any questions.
11. Tighten all screws (do not exert excessive force to avoid breaking the screw or damaging its thread).
12. Drill holes and bolts will be left in the wall, ceiling or floor once the display and bracket are removed. Stains may occur after extended use.
13. Since the manufacturer has no way to control the wall, ceiling or floor type and installation of the mount, the warranty of the product shall only cover the body of the mount. The warranty period of the product is 5 years.
14. Please consult the English language manual for any dispute on conditions.

WWW.NEOMOUNTS.COM.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>