TAOTRONICS TT-BH046 Soundsurge 46 Active Noise Cancelling Wireless Stereo Headphones User Guide

TAOTRONICS TT-BH046 Soundsurge 46 Active Noise Cancelling Wireless Stereo

Headphones

Product Diagram

1. Power Button
2. Volume + / Next Track
3. Volume – / Previous Track
4. 3.5mm Audio Port
5.  Power / Bluetooth Indicator
6.  Microphone
7.  ANC Button (built-in green indicator)
8.  Micro USB Charging Port
9.  Charging Indicator

Package Contents

• 1 x TaoTronics Wireless ANC Headphones
• 1 x USB Charging Cable
• 1 x 3.5mm Audio Cable
• 1 x User Guide
• 1 x Airline Headphone Adapter
• 1 x Carrying Case

How to Use

1. Charging
2. Connect the charging port with any USB charging adapter.
3. Charging will start automatically with the charging indicator turning red.
4. The headphones are fully charged when the charging indicator turns off.

Note:

• For quick charging, you need to use a DC 5V charger with more than 1A.

Pairing

1. Make sure the headphones and your Bluetooth® device are next to each other (within 3ft / 1m).
2. Press and hold the Power Button for 5 seconds to bring the headphones into pairing mode with the power / Bluetooth indicator flashing blue and red alternately.
3. Activate Bluetooth® on your device and search for nearby Bluetooth® connections.
4. Find“TAOTRONICS SoundSurge 46”in the search results. Tap on the name to connect. Once connected, the LED indicator will flash blue once every 3 seconds.

Note:

• The Bluetooth® headphones can remember devices paired previously. You may simply turn on the headphones and the device (with Bluetooth activated), and they will connect to the last connected device automatically without going into the pairing mode.
• To clear the pairing history, Disconnect on your device, and then press and hold the Power and Volume – Buttons simultaneously when the headphones are on until the Bluetooth indicator flashes purple.

Button Functions

indicator flashes / turns off.

Play / Pause /

Answer / Hang up Phone Calls

| Press the Power Button once.
Reject Phone Calls| Press and hold the Power Button for 3 seconds.
Mute the Call / Music| Press Volume + and Volume – Buttons at the same time
Redial| Press the Power Button twice.
Volume + / –| Press the Volume + / – Button
Previous / Next Track| Press and hold the Volume – / + Button
Bluetooth Pairing| Press and hold Power Button for 5s when off

Note:

• The headphones will prompt low battery with the charging indicator light flashing red once every 5s and shut off automatically if battery gets too low.
• The headphones shut off automatically after 10 minutes when no device is connected.
• Switch the ANC Button to turn on / off the active noise cancellation (ANC) function and the built-in indicator will light up green / go out.
• Connect the headphones to a 3.5mm audio port with the audio cable provided and you may apply it with wire.

FCC Rules

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.

References

• TaoTronics Official Site - Technology Enhances Life
• User Manual - TaoTronics – TaoTronics US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>