Fodsports FX8 Air 2 Ways Helmet Intercom User Manual
- June 6, 2024
- Fodsports
Table of Contents
- FX8 Air 2 Ways Helmet Intercom
- FAQs:
- Technical Specifications
- Downloads:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
FX8 Air 2 Ways Helmet Intercom
User Manual
FOCUS ON OUTDOOR SPORTS
1. PACKAGE INCLUDE
2. Charging
2.1 When charging, the LED indicator will light up in red, and the indicator light goes out after the charging is completed(As shown below). Please charge it before using it for the first time.
2.2 Please use 5V/1A*0.5Aqualifled changer to charge the device. Unstable current may damage the equipment. 2.3 Please keep charging at least once every 2 months If the product Is not used for a long time.
3. Installation & Disassembly
3.1 Speaker Installation
Remark: the microphone should be closed to and aim at the mouth as possible. The speakers are as close to ears as possible. If installation position of the speaker is too deep so that the speaker is too far away from the ear, the sponge in accessory may be used to jack up.
3.2 Fixed by clamp
3.3. Disassembly of the Device
4. Button and basic function operation
Power on: Press and hold the intercom button and multi-function button at the same time for about 3 seconds, until the voice prompt “Welcome to FODSPORTS Bluetooth communication system”.
Power off: Press and hold the intercom button and multi-function button at the same time for about 3 seconds, until the voice prompt “Power off’.
Battery detection & low battery automatic reminder function
FX8 AIR has the power detection function. When the device is turned on, short
press the “Previous” button and the “Next” button at the same time.
Power over 90%, the voice will prompt: “beep…beep…beep”.
Power over 50%, the voice will prompt: “beep…beep “.
Power lower than 50%, the voice will prompt:”beep…”.
Low Battery Reminder
When the battery level is less than 20%, you will hear a tone: Power less than
20%, Please Charge.
When the battery level is lower than 10%, the red light of the multi-function button will flash and you will hear a tone: power lower than 10%, it will shut down, please charge it immediately.
Cellphone
Answering Call: Short press multi-Function button.
Hangup Call: Call ended,short press multi-Function button.
Refuse Call: Long press multi-Function button button for 2 seconds.
Redial: Short press multi-Function button twice.
Volume Up: Rotate the multi-Function button forward.
Volume Down: Rotate the multi-Function button Backward.
Switch manual/automatic answering calls: While in standby, press and hold the °Intercom ” button and “Previous” “Next” button and at the same time for 5 seconds. (Default: answer incoming calls automatically)
- Automatic answering calls :the voice prompt “beep…beep”
- Manual answering calls :the voice prompt “beep…”
The headset is connected to 2 mobile phones at the same time
Answer an incoming call: When talking with the first mobile phone, if there is an incoming call from the second mobile phone, quickly press the multi-function button once to end the first mobile phone, and press the multi- function button again to answer the second mobile phone.
Hangup call: To end the call, short press the multi-function button.
Reject incoming call: When there is an incoming call from the second mobile phone during a call, press and hold the multi-function button for 2 seconds to reject the second call.
Voice Command
After FX8 AIR is connected to the cellphone, short press the “Mode” button to activate the voice control function. Requires cellphone with voice control function.
Cellphone must have voice commend function.
Music Function
Play: Short press the multi-function button.
Pause: Short press the multi-function button.
Volume Up: Rotate the multi-Function button forward.
Volume Down: Rotate the multi-Function button Backward.
Play Previous: Short press Previous button.
Play Next: Short press Next button.
EQ Sound Selection
Under the music playing state, short press the Mode button EQ sound effect selection button, you can switch the sound effect when listening to different types of songs.
• Hifi bass -> Corresponding voice: Bass boost
• Popular Golden Classic -> Corresponding voice: Midrange boost
• Pure human voice -> Corresponding voice: Treble boost
APTX HD Audio
In the cellphone song playback format settings, select the APTX format, and you can enjoy real Hi Fi sound effects when the song is played (the mobile phone must supportAPTX format playback)
Intercom Function
Switch Intercom On: short press Intercom button.
Switch Intercom Off: short press Intercom button.
Volume Up: Rotate the multi-Function button forward.
Volume Down: Rotate the multi-Function button Backward.
FM Function
FM ON: Long press Next button for 3 seconds.
FM OFF: Long press Next button for 3 seconds.
Volume Up: Rotate the multi-Function button forward.
Volume Down: Rotate the multi-Function button Backward.
Search channels: short press Previous / Next button .
Memory Clear
Clear patting records: FX8 AIR can manually clear pairing records with other devices. In the standby state of the device, press the “multi-function” button and the Previous song” button at the same time for about 5 seconds, the red and blue indicator lights flash at the same time, and the clearing of the pairing record is completed. (The voice prompt “beep…beep…beep”)
5. Device pairing and connection
5.1 Pairing Mode
5.1.1 Passive search mode
When device is on, press and hold the multi-function button for about 6 seconds, the red and blue indicator lights flash alternately quickly, enter the pairing search mode, and the voice prompt “beep…beep”. The passive pairing mode is used to connect to Bluetooth devices such as mobile phones and GPS.
5.1.2 Active Search mode
When device is on, press and hold the intercom button for about 6 seconds, the red and blue indicator lights flash alternately slowly, enter the active search mode, and the voice prompt “beep…”. Active search mode is used for the intercom function connection between
5.2 (A) FX8 AIR Connect with (B) FX8 AIR
A FX8 AIR is on positive search mode(refer to 5.1.2), B M 1 S-PLUS is on passive search mode(refer to 5.1.1 ),A and B FX8 AIR change from flashing red and blue lights alternately to multi-Function and intercom buttons flashing blue lights at the same time,connect successfully.
5.3 Pairing With Cellphone
STEP-1: When device is on,long press multi-Function button.red and blue light flash quickly, entering passive pairing mode.(refer to 5.1.1)
STEP-2 : Turn on cellphone Bluetooth, select FODSPORTS FX8 AIR, the pairing is complete. Voice message will also say “Device Connected”.
5.4 Connect with two phones
Step-1: Connect to the first phone(refer to 5.3)
Step-2: Long press the multi-function button, FXB AIR enters the passive
search mode again and connects with the second mobile phone (refer to 5.3).
Notice: FXB AIR can connect to 2 phones, but only support one phone for audio input.
5.5 Wire Connecting
FX8 AIR can be connected to audio output devices such as radio, GPS navigator, speedometer, music player, etc. through the standard 2.5 to 3.5mm AUX audio cable.
You need to purchase a cable if you need a wired connection for Walkie-talkie equipment. Note: The wired audio cable function can only be used in standby mode.
6. Pairing connection
6.1 Occasions: Rider A connect with Passenger B for intercom. Then A connect with two Bluetooth devices and one wired equipment and B connect with one Bluetooth device(as shown below).
Step 1: AFXBAIR connect with B FXBAIR{refer to 5.2)
Step 2: Short press one time A or B intercom button to disconnect
intercom
Step 3: A connect with 2 phones(refer to 5.4)
Step 4: A use 2.5 mm to 3.5 mm AUX audio line to connect with one audio
device
Step 5: B connect with one phone(Bluetooth device)Paired connection(refer
to 5.3)
Step 6: Short press intercom button of A or B for connection.
Notice: If A or B need to use the audio function of phone(Bluetooth device), you need to disconnect the intercom.
Remark 2: Intercom is interrupted and reconnected:
In the 2 people intercom state, if there is a mobile phone call, the intercom
will be automatically disconnected, and the intercom state will be
automatically connected after the call is over. If it is interrupted due to
distance or poor signal, please click the intercom button to return to the
intercom state.
6.2 Memory Connection Function
FX8 AIR will remember the paired device, when you use it again, please follow
the steps below:
STEP-1. Switch off all 2 units(A,B) and all Bluetooth devices connected to the headset such as cellphone and GPS. It will affect the pairing)
STEP-2. Switch on Unit A and B, press Unit A intercom button, A and B are connected successfully..
STEP-3. After all 2 units reconnected switch on original connected Bluetooth devices such as cellphone and GPS.
6.3 FX8 AIR can connect up to 2 devices.
FX8 AIR can not pair with three devices at same time.
7. Technical Specifications
- Bluetooth Support: HSP, HFP, A2DP, AVRCP, AGHSP
- Battery: lithium battery, 900mA , 3.7V
- Dimensions: 8.9cm 4.5cm 2.8cm
- Weight: 50G,100G(Include Headphone & Mic Kits)
- Frequency Range: 2.4G-2.485G
- Operating temperature: -20 C-50 C
- Certification: CE FCC ROHS BQB TELEC USB
- Adapter standard charge voltage: DC 5V±0.2V USB
- Adapter standard charge circuit: DC 1A±0.5A
- Charging time: 2-3 hours
8. Q&A / Warning
Q-1. No sounds from one or two side speaker.
Al: Check device plug, needs to firmly connected.
Q-2. Can it be recharged from bike USB charger while riding ?
A2: 1. Not recommended, unstable power source will cause damage on intemal
circuit,may cause unable to recharge/can’t fully charged/can’t switch on.
2.Power bank will be good.
Q-3: When using radio, not transmission or continuous transmission.
A3: Check 2.5mm pin, has to insert firmly. The pin equipped with waterproof
aprons. user might think its already plugged.
Q4: New device can’t switch on.
A4: Recharged at least 30 minutes before switch use.
*Warning
Sound Volume Warning Long period or too loud may hurt hearing ability.
Disassemble or Modification
The FX8 AIR is precisely made in factory.Any disassemble or modification may
damage the device,please do not tear any of the safety regulation and serial
sticker from the device ,that will void the warranty.Please contact us
directly if needed.
9. Statement I Warranty/ After-Sale Service
9.1 FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
9.2 Warranty
In normal use, one year warranty from the date of purchase, any disassemble,
modification will void warranty.
After-Sale Service
For any quality problem or missing accessories, especially pairing problem between 2 or more FX8 AIR headsets, please feel free to contact us at email: winzon.cs@outlook.com. We’re always here ready to help, will reply to you in 24 hours.
FAQs:
Why are my two speakers or one side speaker unavailable/no sound?
A: 1. Please check if the headphone cable is inserted in the correct direction, M1-S PLUS is a Type-C interface, with the microphone icon facing you, and then inserting the interface is the correct direction. 2. Please make sure the headphone cable is fully inserted into the interface.
Why is my microphone unavailable/no sound?
The microphone part is detachable and can replace the soft/boom microphone, so please check if this part is inserted tightly.
Why are my speakers volume low?
Different locations of speakers will cause differences in volume, please install the speaker as close to your ears as possible. If the distance is too far, the volume will be reduced. You can use the thickened pad in the package to achieve it.
Technical Specifications
Manufacturer | Fodsports |
---|---|
Brand | FODSPORTS |
Item Weight | 11.2 ounces |
Product Dimensions | 90mm 40mm 25mm |
Maximum Intercom Distance: | 1000m |
Item model number | FX8 Air |
Batteries | 900mAH |
Manufacturer Part Number | FX8 Air |
Connections | Bluetooth 5.0 |
Headphones Form Factor | 40MM High Impedance & High Fidelity Speaker |
Control Type | Big Button |
FM Support | YES |
Plug Type | Type C |
Downloads:
Fodsports FX8 Air 2 Ways Helmet Intercom Manual – [Optimized PDF ]
Fodsports FX8 Air 2 Ways Helmet Intercom Manual – [Original PDF ]
Fodsports FX8 Air 2 Ways Helmet Intercom Manual – [UK, France, Germany, Spain, Italy PDF ]
Fodsports FX8 Air 2 Ways Helmet Intercom Manual – [Russian PDF ]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>