Whirlpool AKC 950 Gas Hob 5 Burners Instruction Manual
- May 15, 2024
- Whirlpool
Table of Contents
AKC 950 Gas Hob 5 Burners
Instruction Manual
SAFETY INSTRUCTIONS
Download the complete instruction manual on http://docs.whirlpool.eu or call
the phone number shown on the warranty booklet.
Before using the appliance, read these safety instructions. Keep them nearby
for future reference.
These instructions and the appliance itself provide important safety warnings,
to be observed at all times. The manufacturer declines any liability for
failure to observe these safety instructions, for inappropriate use of the
appliance or incorrect setting of controls.
WARNING: If the hob surface is cracked, do not use the appliance – risk of
electric shock.
WARNING: Danger of fire: Do not store items on the cooking surfaces.
CAUTION: The cooking process has to be supervised. A short cooking process has
to be supervised continuously.
WARNING: Unattended cooking on a hob with fat or oil can be dangerous – risk
of fire. NEVER try to extinguish a fire with water: instead, switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
Do not use the hob as a work surface or support.
Keep clothes or other flammable materials away from the appliance, until all
the components have cooled down completely – risk of fire.
Very young children (0-3 years) should be kept away from the appliance. Young
children (3-8 years) should be kept away from the appliance unless
continuously supervised. Children from 8 years old and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge can use this appliance only if they are supervised or have been
given instructions on safe use and understand the hazards involved.
Children must not play with the appliance. Cleaning and user maintenance must
not be carried out by children without supervision.
WARNING: The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Children less than 8 years
of age shall be kept away unless continuously supervised.
PERMITTED USE
CAUTION: the appliance is not intended to be operated by means of an external
switching device, such as a timer, or separate remote controlled system.
This appliance is intended to be used in household and similar applications
such as: staff kitchen areas in shops, offices and other working environments;
farm houses; by clients in hotels, motels, bed & breakfast and other
residential environments.
No other use is permitted (e.g. heating rooms).
This appliance is not for professional use. Do not use the appliance outdoors.
INSTALLATION
The appliance must be handled and installed by two or more persons – risk of
injury. Use protective goves to unpack and install – risk of cuts.
Installation, including water supply (if any), electrical connections and
repairs must be carried out by a qualified technician. Do not repair or
replace any part of the appliance unless specifically stated in the user
manual. Keep children away from the installation site. After unpacking the
appliance, make sure that it has not been damaged during transport. In the
event of problems, contact the dealer or your nearest After-sales Service.
Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored
out of reach of children – risk of suffocation. The appliance must be
disconnected from the power supply before any installation operation – risk of
electric shock. During installation, make sure the appliance does not damage
the power cable – risk of fire or electric shock. Only activate the appliance
when the installation has been completed.
Carry out all cabinet cutting operations before fitting the appliance and
remove all wood chips and sawdust.
If the appliance is not installed above an oven, a separator panel (not
included) must be installed in the compartment under the appliance.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance from the power supply by
unplugging it if plug is accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the wiring rules and the appliance
must be earthed in conformity with national electrical safety standards.
Do not use extension leads, multiple sockets or adapters. The electrical
components must not be accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do not operate this appliance if
it has a damaged power cable or plug, if it is not working properly, or if it
has been damaged or dropped.
Installation using a power cable plug is not allowed unless the product is
already equipped with the one provided by the Manufacturer.
If the supply cord is damaged, it must be replaced with an identical one by
the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard – risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched off and disconnected from the
power supply before performing any maintenance operation; never use steam
cleaning equipment – risk of electric shock.
Do not use abrasive or corrosive products, chlorine-based cleaners or pan
scourers.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the recycle
symbol .
The various parts of the packaging must therefore be disposed of responsibly
and in full compliance with local authority regulations governing waste
disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations. For further
information on the treatment, recovery and recycling of household electrical
appliances, contact your local authority, the collection service for household
waste or the store where you purchased the appliance. This appliance is
marked in compliance with European Directive 2012/19/EU, Waste Electrical and
Electronic Equipment (WEEE) and with the Waste Electrical and Electronic
Equipment regulations 2013 (as amended).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation indicates that
it should not be treated as domestic waste but must be taken to an appropriate
collection center for the recycling of electrical and electronic equipment.
ENERGY SAVING TIPS
Make the most of your hot plate’s residual heat by switching it off a few
minutes before you finish cooking.
The base of your pot or pan should cover the hot plate completely; a container
that is smaller than the hot plate will cause energy to be wasted.
Cover your pots and pans with tight-fitting lids while cooking and use as
little water as possible. Cooking with the lid off will greatly increase
energy consumption.
Use only flat-bottomed pots and pans.
DECLARATION OF CONFORMITY
This appliance meets Ecodesign requirements of European Regulation 66/2014 and
The Ecodesign for Energy-Related Products and Energy Information (Amendment)
(EU Exit) Regulations 2019 in compliance with the European standard EN
60350-2.
INSTALLATION
- The cooktop must be set into a worktop at least 20 mm deep.
- There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).
- Make sure the power cord is long enough to allow convenient installation.
- The distance between the lower face of the glass ceramic hob and the cupboard or separating panel must be at least 20 mm.
- For built-in dimensions and installation see the picture in this paragraph.
- A minimum distance must be maintained between the hob and the hood above it. Please refer to the user manual of the hood for more informations.
- Apply the supplied gasket to the cooktop (unless it has already been fitted), after having cleaned its surface.
- Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam or moisture, which could damage them.
- If an oven is installed beneath the cooktop, make sure that it is equipped with a cooling system. If the temperature of the electronic circuits exceeds the maximum permitted temperature, the cooktop will switch off automatically; in this case, wait for a few minutes until the internal temperature of the electronic circuits reaches a tolerable level, at which point it will be possible to switch the hob on again.
PLACING THE HOB
Important: remove any protective fllm before installing the hob.
Make sure that the opening in the worktop for the hob is cut according to the
dimensions given in the drawing, paying attention to the tolerance range. The
hob should not be forced into the worktop. Forcing the glass-ceramic top may
cause it to crack (even at a later date)!
DIMENSIONS AND DISTANCES TO BE MAINTAINED
REMOVING THE HOB:
To remove the hob, first, disconnect it from the electric supply. It is
strongly recommended to free the underneath part from the oven, drawer,
separator, or other. It allows the technician to access the lower part of the
hob to unfasten the four clips with a screwdriver, lift the hob and remove
it, avoiding any worktop damage.
ELECTRICAL CONNECTION
Electrical connection must be made before connecting the appliance to the
electricity supply.
The power cord is not included in the package – remember to prepare your own
power cord.
Installation must be carried out by qualified personnel who know the current
safety and installation regulations. Specifically, installation must be
carried out in compliance with the regulations of the local electricity supply
company.
Make sure the voltage specified on the data plate located on the bottom of the
appliance is the same as that of the home.
Regulations require that the appliance be earthed: use conductors (including
the earth conductor) of the appropriate size only.
CONNECTION TO THE TERMINAL BLOCK
For the electrical connection, use an H05RR-F or H05V2V2-F cable as specified
in the table below.
| SUPPLY VOLTAGE | CONDUCTORS AMOUNT x SIZE |
|---|---|
| 220-240V ~ + | 3 x 1,5 mm2 |
The appliance must be connected to the electricity supply by means of an all-
pole disconnect switch with minimum contact gap of 3 mm.
ATTENTION: the power supply cable must be long enough to allow the
cooktop to be removed from the worktop and must be positioned so as to avoid
damage or overheating caused by contact with the base.
NOTE: the yellow/green earth wire must be connected to the terminal with
the symbol and must be longer than the other wires.
- Remove approx. 70 mm of the cable sheath from the power supply cable.
- Strip approx. 10 mm of sheath from the wires.
- Open the terminal board by pushing the side clips in with the help of a tool.
- Insert the cable in the cable clamp and connect the wires to the terminal board.
- Close the cover of the terminal board.
- After the electrical connection, fit the hob from the top and hook it to the fixing springs.
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT
In order to receive a more complete assistance, please register your product
on www.whirlpool.eu/register.
Before using the appliance carefully read the Safety Instruction.
PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION
PRODUCT DESCRIPTION
- Radiant cooking zone Ø 145
- Radiant cooking zone Ø 180
- Control knob for rear cooking zone
- Control knob for front cooking zone
FIRST TIME USE
Before use:
- remove adhesives stuck on the hob;
- remove cardboard guards and protective plastic fllm;
- check whether the hob has been damaged during transport. If in doubt, contact the After Sales Service.
DAILY USE
SWITCHING THE HOB ON/OFF
To use the hob turn the knob(s) clockwise and position it (them) on the
required power setting.
To turn the hob off, turn the knob(s) back to position “0”.
IMPORTANT: To avoid a permanent damage the hob:
- do not use pots with bottoms that are not flat;
- do not use metal pots with enamelled bottom;
- do not place hot pots/pans over the control panel.
COOKING TABLE
| KNOB (1-12) | TYPE OF COOKING |
|---|---|
| 1 − 2 | Melting butter, chocolate, etc. |
| 2 − 3 − 4 | Keeping food warm and reheating small quantities of liquid. |
| 4 − 5 − 6 | Heating larger quantities, making custards and sauces. |
| 6 − 7 | Gentle simmering, for example: boiled vegetables, spaghetti, soups, pot |
roasts, stews.
7 − 8| For all fried food, cutlets, steaks, cooking without use of lid, for
example: risotto.
8 − 9 − 10| Browning meats, roast potatoes, fried fish and to boil large
quantities of water.
11 − 12| Brisk frying, griddling steaks, etc.
CLEANING AND MAINTENANCE
Disconnect the appliance from the power supply.
- Do not use steam cleaning equipment.
- Do not use abrasive sponges or scouring pads as they may damage the glass.
- After each use, clean the hob (when it is cool) to remove any deposits and stains from food residue.
- Sugar or foods with a high sugar content can damage the hob and must be immediately removed.
- Salt, sugar and sand could scratch the glass surface.
- Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions).
- Spills of liquid in the cooking zones can cause the pots to move or vibrate.
- After cleaning the hob, dry thoroughly.
TROUBLESHOOTING
If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem.
-
Read and follow the instructions given in the section “Daily use”.
-
Check that the electricity supply has not been shut off.
-
Turn the hob off and on again, to make sure that the problem has been solved.
-
Make sure that the knob is not turned to “0”.
Turn the multi-pole switch to “Off” for a few minutes and then turn it back to “On”. -
The hob will not switch off: disconnect the hob immediately from the power supply.
If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.
AFTER SALES SERVICE
In order to receive a more complete assistance, please register your product
on www.whirlpool.eu/register.
BEFORE CALLING THE AFTER-SALES SERVICE:
- See if you can solve the problem by yourself with the help of the suggestions given in the TROUBLESHOOTING.
- Switch the appliance off and back on again to see if the fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN TOUCH WITH THE
NEAREST AFTER-SALES SERVICE.
To receive assistance, call the number shown on the warranty booklet or follow
the instructions on the website www.whirlpool.eu.
When contacting our Client After sales service, always specify:
- a brief description of the fault;
- the type and exact model of the appliance;
- the serial number (number after the word SN on the rating plate located under the appliance). The serial number is also indicated in the documentation;
- your full address;
- your telephone number.
If any repairs are required, please contact an authorized after-sales service (to guarantee that original spare parts will be used and repairs carried out correctly).
Policies, standard documentation and additional product information can be found by:
- Using QR code in your appliance;
- Visiting our website docs. whirlpool. eu;
- Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales Service, please state the codes provided on your product’s identification plate.