STERLING 7204 Neo Angle Shower Receptor Instruction Manual

June 4, 2024
STERLING

STERLING 7204 Neo Angle Shower Receptor

STERle-LING-7204-Neo-Ang-Shower-Receptor-

WHAT IN THE BOX

STERle-LING-7204-Neo-Ang-Shower-Receptor-
fig-1

Optional

  • Mortar cement
  • Shims
  • Furring Strips
  • Drop cloth

Installation Instructions

Record your model number below for future reference:
Observe all local building and plumbing codes Install on an adequately supported subfloor.
If the subfloor is not level and access to shim is difficult, install with a 1″ (25 mm) to 2″ (51 mm) bed of mortar cement

  1. Construct a plumb stud pocket according to the roughing-in information on the back page.
  2. Install the rough plumbing.
  3. Install the drain to the shower base.STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-4
  4. Staple the felt pad, if provided, to the subfloor so it will contact all support feet.
  5. Without a pad, we recommend the basin area be set in 1″ (25 mm) to 2″ (51 mm) of mortar cement
  6. Lift and position the shower base 6 Lift and position the shower baseSTERle-LING-7204-Neo-Ang-Shower-Receptor-fig-5
  7.  With the unit level, shim under the support feet as needed.
  8. Install plastic attachment clips at all stud locations.STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-6
  9. Connect the drain to the drain pipe. Position a protective liner in the basin.
  10. 10 Custom Walls: Install furring strips, wallboard, and the finished wall as shown.
  11. Install the back wall.STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-7
  12. Measure, mark, and drill the faucet holes in the drain end wall.
  13. Apply an L-shaped bead of silicone sealant at each outside corner. STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-8
  14. Install the end wall. Engage the end wall pin in the back wall slot.
  15. The front edges should be flush, with no more than a 1/32″ (1 mm) gap.
  16. Starting at the bottom, install screws through the dimples to secure the flanges to the studs.STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-9
  17. Secure the walls to the studs along the top. Use shims as needed.
  18. Cover the framing with water-resistant wallboard. Install the finished wall material STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-10
  19. Install the faucet trim and accessories and seal where they contact the wall panels.
  20. After painting, apply 100% silicone sealant where the unit contacts the finished wall. STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-11

Roughing-In, 7204, 7205 Series

STERle-LING-7204-Neo-Ang-Shower-Receptor-fig-12

Need help? Contact the Customer Care Center.
USA/Canada: 1-800-STERLING (1-800-783-7546), Mexico: 001-877-680-1310
For service parts information, visit
sterlingplumbing.com/parts.
For care and cleaning, visit
sterlingplumbing.com/care-and-cleaning.
Patents : kohlercompany.com/patents
This product is covered under the STERLING® Vikrell® or Acrylic Baths and Shower Bases Ten-Year Limited Warranty found at sterlingplumbing.com/warranty. For a hardcopy of warranty terms, contact the Customer Care Center.

USA/Canada: 1-800-STERLING (1-800-783-7546) Mexico: 001-877-680-1310
www.SterlingPlumbing.com 

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

STERLING User Manuals

Related Manuals