TAOTRONICS TT-BH118 True Wireless Earbuds User Manual

TAOTRONICS TT-BH118 True Wireless Earbuds

Specifications

Accessories

Note:
Remove the insulation cover from the earbuds before first use. Put the earbuds into the charging case, and take out for use.
All images in this user manual is for illustrative purpose only. Please refer to the actual product.

FAQ

The indicator is off when the charging case is being charged.
Make sure the charging port of the charging case is connected to power supply nomially.
Cannot hear anything from the earbuds

• Make sure the earbuds are on.
• Make sure the volume is set properly.
• Make sure the earbuds are connected to the phone.
• Make sure the earbuds are within the working range.

Phone call effect is not good
Make sure the phone is in a strong signal area.

The effective working range of the earbuds is 10 meters, please make sure the earbuds are within the working range, and there are no obstacles between the phone and the earbuds.
Cannot control with pause, resume and previous/next track while playing music
The device paired with the earbuds needs supporting AVRCP (AudioNideo Remote Control Profile) Protocol.

Using Your Earbuds

1. Charging
   Charging Earbuds
   When the earbuds prompt low battery, put the earbuds into the charging case, the earbuds will be in charging status automatically and the charging case lights up for 4 seconds before going off. The earbuds indicators stay solid blue while charging; the blue light goes off after the earbuds are fully charged.
   Charging the Case
   Connect the charging case to any 5V/1A power supply port with the included charging cable.
   While charging, the charging case is breathing white slowly.
   After fully charged, the charging case stays solid white.

2. On/Off
   Take out the earbuds from the charging case to turn on.  Put back the earbuds to the charging case and clo se the lid to turnoff.

3. Bluetooth Connection For the first connection, open the lid of the charging case, take out both earbuds, and they will enter Bluetooth pairing mode automatically.
   Earbuds pairing mode: primary earbud flashes blue and white, and secondary earbud has no lighting.
   Search for “TaoTronics NC BH1118”, select to connect, and the primary earbud lighting goes off after the connection is successful.
   When the earbuds are turned on again, they wilt connect to the last paired device. If re-connection fails or the Bluetooth is disconnected, they will enter Bluetooth pairing mode automatically.

4. Dual Earbuds TWS Connection
   Both earbuds were paired with each other when they were produced at the factory.

5. Clearing Pairing History
   Make sure the earbuds were not connected to any device.
   Tap the touch button of any earbud for FOUR times in any of the following status:

   • a. Single earbud pairing (alternatively flashes blue and white)
   • b. Dual earbuds pairing (left earbud flashes blue and white. right earbud has no lighting)
     Both earbuds light up blue for 1 second then go off. Turn off the earbuds by placing them into the case.
     Take out the earbuds to re-pair with your device.

Control & Functions ****

Music:

Pause/Play Double tap UR
Previous Track Triple tap L
Next Track Triple tap R
Volume- Tap L once
Volume+ Tap R once

Calling:

Answer Double tap UR
Hang Up Double tap UR
Reject Tap & Hold UR for 2s

Gaming/Bass/Pop Mode: Tap & Hold L for 2s
ANC/Pass Through/Normal: Tap & Hold R for 2s

(Mode switch is not available for single earbud)

Bluetooth” The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG.Inc. and any use of such marks by Sunvalleytek International Inc. is under license. Other trademarks and trade names are those of their respective owners.

FCC

FCC Compliance

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be detemiined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible ham, to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this

• Email:[email protected]
• Manufacturer: Shenzhen Aspiron Technology Company Limited
• Address: Room 2803B,Building C,Galaxy World Phase II ,Minle Community,Minzhi Street,Longhua Oistrict,Shenzhen,Guangdong,China
• www.taotronics.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>