YiFeng F3 Wireless Charging Bracket User Manual

June 5, 2024
YiFeng

YiFeng F3 Wireless Charging Bracket

SPECIFICATION

Product Name : Wireless Charging Bracket
Product Name : F3
Output: 15W/ 10W/ 7.5W/ SW
Output: 9V-2A/ 12V-1 .5A
Charging Port : Type-C

LED INDICATOR

PATTERN INDICATOR
Power on Green light flashes once
Stand by Lights off
Charging Green light stays on for 20s then goes out
Fully charged Lights off
Suspend charging Green light flashes

COMPATIBILITY

Apple:
iPhone 13 / 13 Pro/ 13 Pro Max/ 13 mini/ 12 / 12 Pro/ 12 Pro Max/ 12 mini/ 11 / 11 Pro/ 11 Pro Max / XS / XS Max / XR / X / 8 / 8 Plus / SE 2
Samsung:
Samsung Galaxy S21/ S21+/ S21 Ultra/ S20/ S20+
I S20 Ultra/ S10/ S10+/ S10e/ S9/ S9+/ SB/ SB+/ SB Active/ S7/ S7 Edge/ S7 Active/ S6 Edge/ S6 Edge+ I S6 Active, Note 20/ Note 20+/ Note 20 Ultra/ Note 10 / Note 10+/ Note 9/ Note 8/ Note 7/ Note 5/ Note FE Other Qi-enabled phones

TROUBLESHOOTING

When your phone can not be charged properly (when the indicator light of the wireless charger is flashing), please remove the phone, wait until the charging logo of the phone disappears and the indicator light of the wireless charger stops flashing, and then put the phone on the wireless charger in the correct position.

To quickly charge the phone, a QC3.0/PD adapter is required.

CAUTION

  • Do not store device in high-temperature environment, including heat caused by intense sunlight or other forms of heat. Do not place device in fire or other excessively hot environments.
    Exposure to fire or temperature above 212F(100-C) may cause explosion.

  • Do not use the wireless charger in excess of its output rating. Overloading outputs above rating may result in a risk of fire or injury to persons.

  • Do not expose the wireless charger to rain or snow.

  • Do not modify, repair or disassemble the unity. If so, please contact the manufacturer.

  • Switch off the wireless charger when not in use.

  • The wireless charger will automatically switch off when disconnected from its wall charger.

  • Make sure to disconnect the device from power when cleaning.

INFLUENCE FACTORS|

SOLUTIONS

---|---
Device Model| Check if your phone is compatible, refer to the COMPATIBILITY list.
Position| Make sure the center of the back of the phone is aligned with the”+”.
Adapter and Charging Cable| Please use certified QC 3.0/PD adapter to charge the device. Do not plug into computer USS port or any other non-certified USB port.
The adapter and the charging cable must be firmly connected. Try to reconnect the adapter and charging cable.
If the problem persists, try a different adapter (9V-2A/ 12V-1.5A)and charging cab le.
Protective Case| The thickness of the protective case (non-metallic) should not exceed 0.2in (5mm). The size of the phone with the case should not exceed 6.45in (164mm).
Try to remove the case and check again.
Interference| Magnetic/ Metal Attachments (such as credit cards, keys, etc.) will interfere the charging.
INFLUENCE FACTORS|

SOLUTIONS

---|---
Temperature| Do not use this product in a high temperature environment or expose it to rain or snow.
It is normal and safe to hear a humming noise when very close to the charger. It means that this wireless charger is adjusting its temperature to achieve a more efficient charging speed.
If your device can not be fully charged, this may due to high environmental temperature, please recharge after the temperature is lowered.
Defective Product| Please contact us through Amazon for technical support following the steps below if the issue remains.

  1. Go to Your Orde rs.
  2. Find your order in the list. 3.Select Problem with order
  3. Choose your topic from list displayed. Select Contact seller.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two condilions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body.

This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the charger, including the antenna. Third-party belt- clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

The device is in compliance with the essential requirements and other relevant provisions of the UK Radio Equipment Regulations SI 2017:1206 (as amended).

  1. The device complies with RF specifications when the device used at 20cm form your body.

Declaration of Conformity:
Hereby, Shenzhen Yifeng Intelligent Technology Co., ltd. Declares that the product F3, TA 1 is in compliance with the following Directives: Radio Equipment Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electrical Equipment 2012. The Full test of the UK declaration of conformity is available at the following internet address:
https://www.YFZN.com

I Radiated H-Field: 17.5 dBµAlm(@10m)(only for EU and UK)
TX/RX frequency range 110-205KHz(only for EU and UK)

Shenzhen Yifeng Intelligent Technology Co., Ltd

10th Floor, Building 2, Chaxi, Zone B, Huafeng First Science Park, Hangcheng Street, Gushu, Baoan District, Shenzhen, China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

YiFeng User Manuals

Related Manuals