Perfit Liner Tri-Fold Hard Folding Tonneau Cover Installation Guide

Perfit Liner Tri-Fold Hard Folding Tonneau Cover

USER MANUAL

GENERAL INFORMATION

Thank you for choosing!
Please read this user manual carefully to ensure correct installation and safe operation.
Our Tonneau hard folding cover uses aircraft-grade alloy aluminum material to provide a strong protection. It will prevent the truck bed from weather exposure and reduce the risk of theft. The Tri-Fold/Quad-Fold design allows easy installation and usage.

Key Features

• durable material
• easy, no drilling installation
• stylish design
• strong protection against weather exposure and theft simple operation with quick release latches
• can be easily folded or removed for oversize cargo

ITEMS LIST

Please open the package and check the quantity of accessories as follows pictures.

Please open the package and check the quantity of accessories as follows pictures.

IMPORTANT – Safety Notice

Please follow all instructions from user manual, failure to comply will VOID your warranty, and may cause severe property damage, injury and/or death.

WARNING: Failure to follow the instruction can result in fatal, serious injury and/or severe property damage.

WARNING: Failure to follow the instruction can lead to property damage and injury.

Before Installation

WARNING

• Please follow all installation guides provided with this user manual.
• Please wear gloves for package opening and cover installation.
• DO NOT install the product if any of the component is missing, damaged or broken.
• Keep this product away from children.

CAUTION

• Only install the product when vehicle is stationary and on level ground.
• Remove unnecessary items on truck bed and/or attached to side rail during installation.
• Before folding and unfolding the panels, make sure the components are secured and remove all other items including any packages, tape, etc.

After Installation

WARNING

• DO NOT drive with tailgate completely or partially open. Tonneau cover MUST be in either completely closed or opened position when vehicle is in movement.
• In closed position, shut the tailgate before rear panel is closed. All panels MUST be flat and all latches MUST be securely engaged to tonneau side rail.
• In opened position, all latching handles MUST be secured before folding the panel. Secure buckle clips by inserting them into the buckle ends located on panel header.
• Whenever the latches are not attached to truck bed side rail, they MUST be secured in the slots on the panel (see figure on the right for correct storage)

CAUTION

• Before folding the panels, remove all other items including ice, snow, leaves, branches, etc.

INSTALLATION GUIDE

These items will need to be installed manually.

1. There are 3 Factory Bolts under the truck rail of each side. Unscrew the Factory Bolts that exist on the truck bed.
(Need T30 head to remove the Factory Bolts)

2. Screw the lower clamp on the truck bed with Factory-Bolt(which is unscrewed in Step 1).

3. Please align the Buckle Mounts according to the holes position in the front bar of tonneau cover, Fasten the screws with the hex key.
Place the tonneau cover on top of the truck bulkhead.

5. Carefully refold the cover without moving position on the truck bed.

6. On the first panel, use these items to assemble two front clamps (insert Alu Buckles and Knob through pre-installed T Bolt)

Slide them towards the side trail and tighten on both ends

Before unfolding the second panel, insert the handles into the pre-installed T bolts

Slide the handles towards the truck bed rail Push down and secure the clamps on both ends

All clamps must contact with the METAL BED RAIL LIP tightly for securing the cover

(If Applicable) Before unfolding the last panel, insert the handles into the pre-installed T bolts

Fold down the last panel

Push down and secure the clamps on both ends

Optional Accessories:
For avoiding any wrong usage,we provide R security pin for dual security for last two handles, please read the pin manual.

(If Applicable) Fold down the last panel, then slide the handles towards the truck bed rail

ATTENTION

SPECIAL CONDITION

If your truck bed covered with long plastic protection on the metal bed rail, pls cut the plastic off, so the clamp can contact and lock on the metal bed rail lip. For the safety usage, please do the same way for the all lock positions if meet same condition. PIs noted that only Lock on the plastic may loosen the clamp handle, and cause the tonneau cover open during driving.

COMPLETION

MAINTENANCE

We uses durable material to build the Tonneau Hard Folding Cover, some simple maintenance is enough to keep the cover’s performance and extend its lifespan.
Check Bolts Engagement

We recommends the user to check the cover is securely attached to the truck bed from time to time. Look for any loose bolts due to road vibrations, cargo contact, etc. Make sure all mount points of the cover are properly attached.

Inspect the Handles

We recommends the user to periodically check the handles on each panel. Remove any dirt or dust from the handle and side rail to allow the component to work without unnecessary resistance. Lubricate the handles from time to time so the handles can move freely during engaging and disengaging.

Clean the Surface

Use a sponge or soft cloth with water and soap to gently remove any dust or dirt off the surface.

FAQ

Q: What should I do if I encounter difficulties during installation?

A: If you face challenges during installation, please refer to the user manual for detailed instructions. If problems persist, contact our customer support for assistance.

Q: Is it necessary to use all provided accessories during installation?

A: Yes, all provided accessories are essential for proper installation and secure operation of the tonneau cover. Do not skip any steps or components mentioned in the user manual.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>